JAI GO-5000M-PGE-1 User manual

Thank you for purchasing this product.
Be sure to read this documentation before use.
This documentation includes important safety precautions and instructions on how to operate the unit. Be sure to read this documentation to ensure
proper operation.
The contents of this documentation are subject to change without notice for the purpose of improvement.
© 2023 JAI
User Manual
GO-5000M-PGE-1
GO-5000M-PGE-UV-1
CMOS Digital Progressive Scan
Monochrome and Monochrome UV Camera with GigE Interface
Document Version: 1.0
Date: 2023-09-15

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Table of Contents
- 2 -
Table of Contents
Table of Contents 2
About Technical Note 5
Notice/Warranty 6
Notice 6
Warranty 6
Certifications 6
CE Compliance 6
FCC 6
Warning 7
KC 7
China RoHS 8
Usage Precautions 9
Notes on Cable Configurations 9
Notes on LAN Cable Connection 9
Notes on Attaching the Lens 9
Phenomena Specific to CMOS Image Sensors 10
Notes on Exportation 10
Features 11
Parts Identification 12
①Lens Mount (C-Mount) 12
②RJ-45 Connector 13
③POWER/TRIG LED 13
④LINKLED 14
⑤ACTLED 14
⑥DC IN/TRIG Connector (6-Pin Round) 15
⑦Mounting Holes (M3, 3mm depth) 15
Preparation 16
Step 1: Install the Software (First Time Only) 17
Step 2: Connect Devices 17
①Lens 18

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Table of Contents
- 3 -
②Direct Mounting (or Use MP-43 Tripod AdapterPlate) 18
③LAN Cable 19
➃Network Card 19
⑤DC IN / Trigger IN Connection Cable 19
⑥AC Adapter (Power Supply) (If Necessary) 19
Step 3: Verify Camera Operation 20
Step 4: Verify the Connection between the Camera and PC 20
Step 5: Change the Camera Settings 23
Step 6: Adjust the Image Quality 24
Adjust the Gain 25
Adjust the Black Level 26
Step 7: Save the Settings 26
To Save User Settings 27
To Load User Settings 28
Main Functions 29
Digital IN/OUT Interface 29
GPIO IN/OUT Matrix 32
Optical Interface 33
Characteristics of Optical Interface 34
Opt In Filter Selector Function 35
Pulse Generator 35
Sensor Layout 41
Camera Output Format 42
Pixel Format 43
Output Timing (Horizontal) 44
Output Timing (Vertical) 45
ROI (Region of Interest) Settings 47
Digital Output Bit Allocation 47
Acquisition Control 48
Acquisition Mode 49
Acquisition Start 52
Acquisition Stop 52

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Table of Contents
- 4 -
Acquisition Frame Rate 52
Calculation of the Maximum Frame Rate 53
Exposure Mode 55
Trigger Control 57
Normal Continuous Operation 60
Timed Mode 61
Trigger Width Mode 62
RCT (Reset Continuous Trigger) Mode 63
Video Send Mode 64
Sequence Mode 65
Trigger Sequence Mode Basic Timing 66
Sequence Index Table (Default) 67
Descriptions of Index Table Parameters 68
Multi ROI Mode 69
Operation and Function Matrix 70
Black Level Control 71
Gain Control 72
LUT (Lookup Table) 74
Gamma 75
Blemish Compensation 76
ALC (Automatic Level Control) 76
HDR (High Dynamic Range) 77
Non-Volatile Flash Memory 78
Miscellaneous 79
External Appearance and Dimensions 79
Spectral Response 80
Specifications 81
User's Record 85
Revision History 86

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Table of Contents
- 5 -
About Technical Note
Some additional technical information is provided on the JAI website as Technical Notes. In this
manual, if a technical note is available for a particular topic, the above icon is shown. Please refer to
the following URL for Technical notes.
https://www.jai.com/support-software/technical-notes

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Notice/Warranty
- 6 -
Notice/Warranty
Notice
The material contained in this manual consists of information that is proprietary to JAI Ltd., Japan, and
may only be used by the purchasers of the product. JAI Ltd., Japan makes no warranty for the use of
its product and assumes no responsibility for any errors which may appear or for damages resulting
from the use of the information contained herein. JAI Ltd., Japan reserves the right to make changes
without notice.
Company and product names mentioned in this manual are trademarks or registered trademarks of
their respective owners.
Warranty
For information about the warranty, please contact your factory representative.
Certifications
CE Compliance
As defined by the Directive 2014/30/EU of the European Parliament and of the Council, EMC
(Electromagnetic compatibility), JAI Ltd., Japan declares that GO-5000M-PGE-1 and GO-5000M-
PGE-UV-1 comply with the following provisions applying to their standards.
EN55032:2015/A11:2020 Class A
EN55035:2017/A11:2020
FCC
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
lReorient or relocate the receiving antenna.
lIncrease the separation between the equipment and receiver.

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Notice/Warranty
- 7 -
lConnect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
lConsult the dealer or an experienced radio/TV technician for help.
Warning
Changes or modifications to this unit not expressly approved by the party responsible for FCC
compliance could void the user’s authority to operate the equipment.
KC
제조년월은 제품상자의 라벨을 참조하십시오.

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Notice/Warranty
- 8 -
China RoHS
The following statement is related to the regulation on “Measures for the Administration of the Control
of Pollution by Electronic Information Products “, known as “China RoHS“. The table shows contained
Hazardous Substances in this camera.
mark shows that the environment-friendly use period of contained Hazardous Substances is 15
years.
重 要 注 意 事 项
有毒有害物质或元素名称及含量表
根据中华人民共和国信息产业部『电器电子产品有害物质限制使用管理办法』， 本产品《有毒有害
物质或元素名称及含量表》如下．
部件名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
GO-5000M-PGE-1
GO-5000M-PGE-UV-1 × 〇 〇 〇 〇 〇
〇:表示该有毒有害物质在该部件所有均质材料中的含量均在 GB/T 26572-2011规定的限量要求以下。
×:表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572-2011规定的限量要求。
环保使用期限
电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外 泄或突变、
电子信息产品用户使用该电子信息产品不会对环境造成严重污染 或对其人身、财产造成
严重损害的期限。
数字「15」为期限15年。

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Usage Precautions
- 9 -
Usage Precautions
Notes on Cable Configurations
The presence of lighting equipment and television receivers nearby may result in video noise. In such
cases, change the cable configurations or placement.
Notes on LAN Cable Connection
Secure the locking screws on the connector manually, and do not use
a driver. Do not secure the screws too tightly. Doing so may wear
down the screw threads on the camera. (Tightening torque: 0.147 Nm
or less)
Caution: Secure manually. Do not secure too tightly.
Notes on Attaching the Lens
How to Clean a Sensor
Avoiding Dust Particles
When attaching the lens to the camera, stray dust and other particles may adhere to the sensor
surface and rear surface of the lens. Be careful of the following when attaching the lens.
lWork in a clean environment.
lDo not remove the caps from the camera and lens until immediately before you attach the lens.
lTo prevent dust from adhering to surfaces, point the camera and lens downward and do not
allow the lens surface to come into contact with your hands or other objects.
lAlways use a blower brush to remove any dust that adheres.
lNever use your hands or cloth, blow with your mouth, or use other methods to remove dust.

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Usage Precautions
- 10 -
Phenomena Specific to CMOS Image Sensors
The following phenomena are known to occur on cameras equipped with CMOS image sensors.
These do not indicate malfunctions.
lAliasing: When shooting straight lines, stripes, and similar patterns, vertical aliasing (zigzag
distortion) may appear on the monitor.
lBlooming: When strong light enters the camera, some pixels on the CMOS image sensor may
receive much more light than they are designed to hold, causing the accumulated signal charge
to overflow into surrounding pixels. This “blooming” phenomenon can be seen in the image but
does not affect the operation of the camera.
lFixed pattern noise: When shooting dark objects in high-temperature conditions, fixed pattern
noise may occur throughout the entire video monitor screen.
lDefective pixels: Defective pixels (white and black pixels) of the CMOS image sensor are
minimized at the factory according to shipping standards. However, as this phenomenon can be
affected by the ambient temperature, camera settings (e.g., high sensitivity and long exposure),
and other factors, be sure to operate within the camera’s specified operating environment.
Notes on Exportation
When exporting this product, please follow the export regulations of your country or region.

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Features
- 11 -
Features
This camera is an industrial progressive scan camera equipped with a Type 1 global shutter CMOS
image sensor with 5.2 effective megapixels (2560 × 2048). The GO-5000M-PGE-UV-1 model has
sensitivity in the UV region.
The unit is compact and lightweight in design and is equipped with GigE Vision Ver 1.1 interface.
Compact and lightweight
The unit’s compact size (approx. 29mm × 29mm × 41.5mm, excluding lens mount) and lightweight
design) allows for easy assembly and installation.
Feature Overview
lNew compact and rugged housing series, 1” progressive scan camera
lIntelligent body design for easy and flexible installation
lUtilizes new GigE Vision ver.1.1 and IEEE802.3af PoE
lAspect ratio 5:4, 2560 (H) x 2048 (V) - 5 million effective pixels
l5 μm square pixels
lS/N 55 dB with Dark Compression ON
l8-bit, 10-bit or 12-bit output
l22.3 frames/second with full resolution in continuous operation (8-bit)
lVarious readout modes, including horizontal and vertical binning and ROI (Region Of Interest)
for faster frame rates
l0dB to +24dB gain control
l10 μs (1/100,000) to 8 seconds exposure control in 1 μs step
lAuto exposure control
lTimed and trigger width exposure control
lRCT trigger mode for specific applications
lALC control with combined function of AGC and Auto Shutter
lHDR (High Dynamic Range) function is available
lVarious pre-processing circuits are provided

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Parts Identification
- 12 -
Parts Identification
①Lens Mount (C-Mount) ②RJ-45 Connector
③POWER/TRIG LED ④LINKLED
⑤ACTLED ⑥DC IN/TRIG Connector (6-Pin Round)
⑦Mounting Holes (M3, 3mm depth)
①Lens Mount (C-Mount)
Mount a C-mount lens, microscope adapter, etc. here.
Note: Before mounting a lens, be sure to refer to ①Lens and confirm the precautions for
attaching a lens and the supported lens types.

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Parts Identification
- 13 -
②RJ-45 Connector
Connect a Gigabit Ethernet compatible LAN cable (Category 5e or higher, Category 6 recommended)
here.
RJ45
GigE Vision Interface
Pin No. IO Signal
1In/Out MX1+ (DA+)
2In/Out MX1– (DA–)
3In/Out MX2+ (DB+)
4In/Out MX3+ (DC+)
5In/Out MX3– (DC–)
6In/Out MX2– (DB–)
7In/Out MX4+ (DD+)
8In/Out MX4– (DD–)
③POWER/TRIG LED
Indicates the power or trigger input status.
LED Status
Lit amber Camera initializing
Lit green Camera in operation
Blinking
green
During operation in trigger mode, trigger signals are being input.
Note: The blinking interval is not related to the actual input interval of the external
trigger.

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Parts Identification
- 14 -
④LINKLED
Indicates whether the GigE network connection is established or not.
LED Status
Off The network link is not established (or in progress).
Lit green 1000Base-T link is established.
⑤ACTLED
Indicates the GigE network status.
LED Status
Off Communication is not active.
Blinking amber Communication is active.

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Parts Identification
- 15 -
⑥DC IN/TRIG Connector (6-Pin Round)
Connect the cable for a power supply (optional) or for DC IN / trigger IN here.
Camera Side: HR10A-7R-6PB (73) (Hirose Electric or equivalent)
Cable Side: HR10A-7P-6S (Plug) (Hirose Electric or equivalent)
Pin No. Input/Output Signal Description
1 Power In DC In DC +12V ~ +24V
2 In Opto In1 GPIO 5
3 Out Opto Out 1 GPIO 1
4 Out Opto Out 2 GPIO 2
5 Opto Common
6 GND GND
Note: Refer to the Digital IN/OUT Interface topic as well.
⑦Mounting Holes (M3, 3mm depth)
Use these holes when attaching an MP-43 tripod adapter plate (optional) or mounting the camera
directly to a wall or other structural system.

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Preparation
- 16 -
Preparation
Read this section to learn how the camera connects to devices and accessories. The preparation
process is described below.
1
Step 1: Install the Software (First Time Only)
lInstall the software for configuring and controlling the camera (eBUS SDK for JAI) on the
computer.
2Step 2: Connect Devices
lConnect the lens, LAN cable, AC adapter, computer, and other devices.
3Step 3: Verify Camera Operation
lVerify whether the camera is turned on and ready for use.
4Step 4: Verify the Connection between the Camera and PC
lVerify whether the camera is properly recognized via Control Tool.
5
Step 5: Change the Camera Settings
lRefer to the procedure for changing the output format setting as an example and change various
settings as necessary.
6
Step 6: Adjust the Image Quality
lRefer to the procedures for adjusting the gain and black level as examples and adjust the image
quality.
7Step 7: Save the Settings
lSave the current setting configurations in user memory.

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Preparation
- 17 -
Step 1: Install the Software (First Time Only)
When using the camera for the first time, install the software for configuring and controlling the camera
(eBUS SDK for JAI) on the computer.
Note: When you install eBUS SDK for JAI, eBUS Player for JAI will also be installed.
1. Download the eBUS SDK for JAI from the JAI website (https://www.jai.com/support-software/jai-
software).
2. Install eBUS SDK for JAI on the computer.
Step 2: Connect Devices
①Lens
②Direct Mounting (or Use MP-43 Tripod AdapterPlate)
③LAN Cable
➃Network Card
⑤DC IN / Trigger IN Connection Cable
⑥AC Adapter (Power Supply) (If Necessary)

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Preparation
- 18 -
①Lens
C-mount lenses with lens mount protrusions of 10 mm or less can be attached.
To prevent vignetting and to obtain the optimal resolution, use a lens that will cover the image sensor
size.
Image Sensor
Mono Type 1 12.8mm x 10.24mm (16.392mm diagonal)
Cautions:
lThe maximum performance of the camera may not be realized depending on the lens.
lAttaching a lens with a mount protrusion of 10 mm or longer may damage the lens or
camera.
Notes:
The following formula can be used to estimate the focal length.
Focal length = WD / (1 + W/w)
WD: Working distance (distance between lens and object)
W: Width of object
w: Width of sensor
②Direct Mounting (or Use MP-43 Tripod AdapterPlate)
When mounting the camera directly to a wall or other device, use screws that match the camera
locking screw holes on the camera (M3: depth 3mm).
Use the supplied screws to attach the tripod adapter plate (lower mounting holes).
Caution: For heavy lenses, be sure to support the lens itself. Do not use configurations in which
its weight is supported by the camera.

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Preparation
- 19 -
③LAN Cable
Connect a LAN cable to the RJ-45 connector.
lUse a LAN cable that is Category 5e or higher (Category 6 recommended).
lUse a LAN cable that is an STP cable.
lWhen supplying power via PoE, connect to a PoE-compatible switching hub or a PoE-
compatible network card.
lRefer to the specifications of the cable for details on its bend radius.
Caution: See the Notes on LAN Cable Connection topic as well.
➃Network Card
Install this in the computer that will be used to configure and operate the camera. As the camera
supports PoE, you can also use PoE-compatible network cards. Refer to the instruction manual of the
network card and configure settings on the computer as necessary.
⑤DC IN / Trigger IN Connection Cable
Performs external I/O such as power supply and trigger input.
⑥AC Adapter (Power Supply) (If Necessary)
Connect the AC adapter and the round connector of the connection cable to the DC IN / Trigger IN
connector on the camera.

GO-5000M-PGE-1 | GO-5000M-PGE-UV-1 | User Manual (Ver. 1.0) Preparation
- 20 -
Step 3: Verify Camera Operation
When power is supplied to the camera while the necessary equipment is connected, the
POWER/TRIG LED at the rear of the camera lights amber, and initialization of the camera starts.
When initialization is complete, the POWER/TRIG LED lights green.
Verify whether power is being supplied to the camera by checking the rear LED. When properly turned
on, the power LED is lit green.
For details on how to read the LEDs, see the ③POWER/TRIG LED section.
Step 4: Verify the Connection between the Camera and PC
Verify whether the camera is properly recognized via Control Tool.
1. Launch eBUS Player for JAI
eBUS Player for JAI startup screen appears.