Baso BAS-6026 User manual

BAS - 6026
(MINI PRINTER)
Operating Manual
BASO ENGINEERING CO.,LTD
<All right reserved in BASO Engineering Co., Ltd.>

THERMAL PRINTER SPEC
BAS - 6026
1. Basic Features
1.) Type : PANEL Mounting or DESK top type
2.) Printing Type : THERMAL PRINT
3.) Printing Speed : 25mm / SEC
4.) Printing Column : 24 COLUMNS
5.) FONT : 24 X 24 DOT MATRIX
6.) Character : English, Numeric & Others
7.) Paper width : 57.5mm ± 0.5mm
8.) Character Size : 5times enlarge possible
9.) INTERFACE : CENTRONICS PARALLEL I/F
SERIAL I/F
10.) DIMENSION : 122(W) X 90(D) X 129(H)
11.) Operating Temperature range : 0℃ - 50℃
12.) Storage Temperature range : -20℃ - 70℃
13.) Outlet Power : DC 12V ( 1.6 A )/ DC 5V ( 2.5 A)
14.) Application : Indicator, Scale, Factory automation equipments
and any other data recording, etc.,,
- 1 -

1) SERIAL INTERFACE SPECIFICATION
* CONNECTOR : 25 P FEMALE PRINTER : 4 P CONNECTOR
3 ( TXD ) ----------------------- 2 ( RXD ) 2
2 ( RXD ) ----------------------- 1 ( TXD ) 3
7 ( GND ) ----------------------- 4 ( GND ) 5
2) BAUD RATE SELECTION
* PROTOCOL : XON / XOFF Type
DIP SWITCH (4) ON : Combination type * DATA BIT : 8 BIT
STOP BIT : 1 STOP BIT
OFF: Complete type PARITY CHECK : NO PARITY
* DEFAULT VALUE : BAUD RATE
(9600 BPS)
- 2 -
DIP SWITCH
1 2 3
BUAD RATE
ON ON ON 150
OFF ON ON 300
ON OFF ON 600
OFF OFF ON 1200
ON ON OFF 2400
OFF ON OFF 4800
ON OFF OFF 9600
OFF OFF OFF 19200

PRINTING COMMAND
* Explanation
Command is composed of One Byte Control code and ESC code.
This arrangement is started with ESC code which is connected by character & numeric code
The control code in Printer does not be still in standardization (ESC Control Code).
All printers have a code structure by themselves.
The control code of Mini - Printer series is designed by popularally IBM & EPSON Printer.
So, it can be comfortable with almost printers.
Print command +- One Byte Control : Form Feed, Carriage Return, Line Feed
|2 times width enlarge cancel (14H)
+- ESC Control code : ESC Hexadecimal n
1. Command List
- One Byte Control
- ESCControlcode
- 3 -
One Byte Control Contents
LF ( OH )
FF ( OCH )
CR ( ODH )
DC4 ( 14H )
1 Line Feed
Form Feed
Carrige return
2 times width cancel
ESC Control code Contents
ESC R n
ESC U n
ESC I n
Reverse print(n=1 : Reverse print), (n=0 : Normal print)
2 times vahre enlarge (n=2 : 2times enlarge)
2 times width enlarge cancel (One Byte control code14H)
Reverse print (n=1 : Reverse print), (n=0 : Normal print)

2. Command Explanation
Code control
1) One Byte Code
The Paper is fed by 1 line.
BASIC Program :
10 FOR i=1 TO 11 STEP 2
20 LPRINT " Line feed test " ; CHR$ (10);
40 NEXTi
Print Ex) Line feed test 1 Line feed
Line feed test
Line feed test
Line feed test
It is printed at the starting position at next page
-4-
Code arrange Function
Format
ASCII : ASCII mechanical arrangement
Decimal : Decimal arrangement
Hexadecimal : Hexadecimal arrangement
LF Line Feed
Format : ASCII : LF
Decimal : 10
Hexadecimal : 0AH
FF Form Feed
Format : ASCII : FF
Decimal : 12
Hexadecimal : 0C
CR Carriage return
Format : ASCII : CR
Decimal : 13
Hexadecimal : 0D

The data in buffer is printed when carriage return is executed, and the paper is
Supplied at one column.
This command is resized to normal from 2 times sized character by ESC U
2) ESC control code
<Notice> Command : If n=1, it is "Reverse print status. (n=0 : Normal print)
Default Value is n=0 in factory set.
The command of reverse & 2 times enlarge can be used together.
It can be effected before input of ESC R 0 code
BASIC Program :
10 LPRINT " REVERS print test " ; CHR$(10) ;
20 LPRINT CHR$(27) ; " R " ; CHR$(1) ; → Reverse print N
30 LPRINT " REVERS print test " ; CHR$(10) ;
40 LPRINT CHR$(27) ; " u " ; CHR$(2) ; → 2 times width enlarge print
50 LPRINT " REVERS print test " ; CHR$(10) ;
Print Ex)
- 5 -
DC4 2 times width cancel
Format : ASCII :
Decimal :
Hexadecimal
DC4
20
14
ESC R Reverse Print
Format : ASCII :
Decimal :
Hexadecimal :
ESC R n
27 82 n
1BH 52H n
← Reverse
← Reverse + 2 times enlarge
REVERS print test

The graph or character according to this command is printed by n times with
normal width.
n is within 1-5 range. Default value is "n=1".
This means normal width.
BASIC Program:
10 FOR I=1 TO 5 'from 1 to 5 times
20 LPRINTER CHR$(27) ; ″ U ″ ; CHR$(I) ; 'ESC U command
30 LPRINTER ″TEST″; 'print string
40 NEXT I
50 LPRINTER CHR$(13) ; 'CR command
Print Ex :
TEST
The graph or character according to this command is printed by n times with normal width.
n is within 1-5 range. Default value is "n=1". This command is set only at the
starting of line, and this line is enlarged by n times.
BASIC Program:
10 FOR I=1 TO 5 'from 1 to 5 times
20 LPRINTER CHR$(27) ; ″ V ″ ; CHR$(I) ; 'ESC V command
30 LPRINTER ″TEST″;
'print string
40 NEXT I
50 LPRINTER CHR$(13) ; 'CR command
- 6 -
ESC V Height enlarge
Format : ASCII : ESC V n
Decimal : 27 86 n
Hexadecimal : 1B 56 n
ESC V Height enlarge
Format : ASCII : ESC V n
Decimal : 27 86 n
Hexadecimal : 1B 56 n

This command can be printed for the graphic.
ESC + K : Command header
n1 : This is lower byte of dot quantity to be able to print.
n2 : This is upper byte of dot quantity to be able to print
0x0D : This command is for the finishing of BIT IMAGE PRINT command.
<Caution> The combination value of n1 and n2 can not be beyond of 576 DOT.
Ex) If 240 X 320 of graphic LCD want to print ;
After ESC,K is transferred, transfer n1 ( = 240 ) & n2 ( = 0 ) consecutively.
And, 240BYTE of BIT DATA is also transferred.
In order to remaining BIT DATA after transferred of 240BYTE data,
Please transfer ESC,K,240,0, then transfer repeatedly transfer 240BYTE data.
If IMAGE DATA is transferred perfectly, BIT IMAGE PRINT Command can be finished by
transferred of 13 (decimal, = or OD (hexadecimal)).
Repeating count : It is 240 x 320 LCD. Therefore, the count is 320/8 = 40.
PRINTER(25PFEMALE) COMPUTER(9P)
2TXD 2TXD
3RXD 3RXD
7 GND 7 GND
- 7 -
ESC K Print bit image
Format : ASCII : ESC K n1 n2 ... data ...
Decimal : 27 75 n1 n2 ... data ...
HEXADEcimal : 1B 4B n1 n2 ... data ...

- 8 -
Fr
o
n
t
Vi
e
w
Rear View
S
i
de
Vi
e
w