Baumr-AG STRBRKBMRAW28 User manual

Wall Mount 44-Piece Tool and
Parts Bin Rack
User Guide
Safety
•This unit is not a toy and should be kept out of the reach of children.
•Small parts are included that may pose a choking hazard to children and animals. Keep parts away from children
and pets.
•Before assembly, ensure there are no missing or defective parts. Contact the retailer if any parts are missing or
defective.
•Assemble only as instructed in this guide. Any deviation or shortcut may lead to incorrect assembly or be
considered customer misuse. Improper assembly may cause damage or serious injury.
•Do not mount the unit to a vehicle.
•Do not over-tighten mounting screws or parts during assembly as this may damage the unit.
WARNING
•The unit should only be mounted on a flat, perpendicular and stable surface.
•Do not exceed the maximum load capacity as this may result in damage or serious injury. Load capacity
depends on the mounting surface and number of fasteners used.
•For stability, heavier items should always be placed lower on the racks.
•Do not rest or support items against or on the unit.
CAUTION
•To ensure continued safety, regularly check that the unit is secure and safe to use (every 3 months). Take
appropriate action to rectify any unstable or unsafe units.
•If you do not understand this guide, or have any doubts regarding safety of the assembly, seek advice and
guidance from a qualified person.
•Appropriate protective equipment, such as safety glasses, must be worn and precautions taken when installing this
product.
•It is recommend that two persons install the unit.
•Before installation, ensure the supporting surface will safely support the combined weight of the unit and all stored
items. If unsure, contact a qualified contractor for guidance.
Cleaning and Care
Clean the unit using a damp cloth. Avoid using harsh or abrasive chemicals as this can damage surface finishes.
Included Items
1. Peg Board x2
2. 40mm Hook x6
3. 30mm Hook x4
4. Drill Holder x1
5. Wrench Holder x2
6. Universal Tool Holder x1
7. Small Bin x16
8. Medium Bin x8
9. Large Bin x4
10. Mounting Screw / Wall Plug x16
Note: Tools and accessories not included.

Disposal
Warranty
Please recycle where facilities exist. Check with your local authority for recycling advice.
Retain your purchase receipt or statement as proof of purchase and date.
The warranty applies only if the product is assembled and used solely in the manner indicated in this guide, and all other instructions have
been followed accurately. Any abuse of the product, incorrect assembly or the manner in which it is used will void any warranty.
No rights are given under this warranty to a person acquiring the product second-hand or when used for commercial use.
Assembly
1. Hold a peg board (1) in position on the wall/mounting
surface (A). Ensure that the peg board is level.
2. Using a pencil or other device, mark out the mounting
holes on the wall / mounting surface. Alternatively,
measure the peg board mounting hole centres and mark
out accordingly. It is recommended to use 8 mounting
points per peg board.
3. Create the necessary holes in the wall/mounting
surface. If the surface is masonry or brick, drill suitable
holes and use the supplied wall plugs or other suitable
anchors. For wood, drill pilot holes, or screw directly into
the wood. If mounting to plasterboard or drywall
surfaces, use appropriate fasteners.
4. Fasten the peg board to the wall/mounting surface
using the supplied screws (2) or other suitable fasteners.
5. Arrange the tool holders, hooks and storage bins as
required (larger bins and heavier items on the lower
rails). Hook each item to the mounting rails and holes on
the peg board and ensure it is secure before using it.

Some experts believe that the incorrect or prolonged use of almost any product may
cause serious injury or death. To help reduce your risk of serious injury or death, refer
to the information below. For more information, see www.datastreamserver.com/safety
Consult all documentation, packaging and product
labelling before use. Note that some products feature
documentation available online. It is recommended to
print and retain the documentation.
Before each use, check the product for loose/broken/
damaged/missing parts, wear or leaks (if applicable).
Never use a product with
loose/broken/damaged/missing parts, wear or leaks.
Products must be inspected and serviced (if
applicable) by a qualified technician every 6 months.
This is based on average residential use by persons of
average size and strength, and on a property of
average metropolitan size. Use beyond these
recommendations may require more frequent
inspections/servicing.
Ensure that all users of the product have completed a
suitable industry recognised training course before
being allowed access to the product.
If this product has been purchased in error when
considering the information presented here, contact
the retailer directly for details of their returns policy, if
required.
The product has been supplied by a general
merchandise retailer that may not be familiar with your
specific application or description of application. Be
sure to attain third-party approval from a qualified
specialist for your application before use, regardless of
any assurances from the retailer or its representatives.
This product is not intended for use where fail-safe
operation is required. As with any product (for
example, automobile, computer, toaster), there is the
possibility of technical issues that may require the
repair or replacement of parts, or the product itself. If
the possibility of such failure and the associated time it
may take to rectify could in any way inconvenience the
user, business or employee, or financially affect the
user, business or employee, then the product is not
suitable for your requirements. This product is not
intended for use where incorrect operation or a failure
of any kind, including but not limited to, a condition
requiring product return, replacement, parts
replacement or service by a technician may cause
financial loss, loss of employee time or an
inconvenience requiring compensation.