Bayco SL-1522 User manual

SL-1522
•Dual light fixtures mounted on a 6’ tripod stand
producing 4,400 Lumens
•Each light fixture can be pointed in different
directions for maximum lighting
•Light fixture base unit can be removed from
tripod stand for low angle illumination
•The tripod stand will extend the lights up to 6
feet high
LED Convertible
Dual Fixture
Work Light on
Tripod Stand

FLY-SL-1522-15
LED Single Fixture Work Light
SL-1522 Features:
•Dual light fixtures mounted on a 6’ tripod stand producing a combined
illumination of 4,400 lumens
•Each light fixture can be pointed in different directions for maximum
lighting
•Light fixture base unit can be removed from tripod stand for low angle
illumination
•The tripod stand will extend the lights up to 6 feet high
•Multi-angle tilt and swivel fixture design
•Multi-fin heat sink keeps lights cool to the touch
•Each LED is rated at 50,000 hours of life
•Comfort-grip padded handle
•Each fixture has its own sealed push button switch for independent
operation
•Tempered glass lens
•6 ft. SVT 18/3 cord with grounded plug
•Powder coated for long wear
•Impact, chemical and water resistant design
•1 Year Limited warranty
SL-1522 Specifications:
•Floodlight Lumens: 2,200/4,400
•Floodlight Color: White
•Type of Floodlight: Solid
•Switch Function: 2 Sealed Push Button
•Light Source: LED
•Case Material: Aluminum
•Cord Length: 6 Ft.
•Cord Gauge: 18/3
•Cord Jacket: SVT
•Cord Color: Black
•Body Color: Black/Red
•Power Source: AC
•Package Contents: Product
•Warranty: 1 Year Limited
•UPC: 0 17398 80447 9
Limited 1 Year Warranty • Product is warranted to be free from defects in workmanship and materials to the original purchaser for one (1) year from the date of purchase, and includes the LEDs, housing, lenses,
electronics, switches, rechargeable batteries and chargers. Disposable non-rechargeable batteries are excluded from this warranty. Normal wear and failures which are caused by accidents, misuse, abuse, faulty
installation and lightning damage are also excluded.

WARNINGS
IMPORTANT SAFETY INSTRUCTIONS
WARNING: READ ALL INSTRUCTIONS CAREFULLY
SAVE THESE INSTRUCTIONS
WARNING: When using outdoor lights, basic safety precautions should always be
followed to reduce the risk of fire, electrical shock, and personal injury, including
the following:
Not intended for use in wet areas.
DO NOT use with extension cord near water or where water may accumulate.
Keep plugs and receptacles dry.
For use only on GFCI protected circuits.
Use only three-wire outdoor extension cords 16 AWG or larger that have three-prong
grounding plug and receptacles that accept the appliance’s plug.
DO NOT use this work light with a 2 wire extension cord
Use only three-wire extension cords rated for outdoor use, such as an extension
cord of cord type SEW, SEOW, SEEOW, SEOOW, SOW, SOOW, STW, STW, STOW,
STOW, STOOW, SJEW, SJEOW, SJW, SJW, SJOW, SJOOW, SJTW, SJTOW, OR
SJTOOW.
SAVE THESE INSTRUCTIONS
Instruction Manual
SL-1522
THANK YOU FOR PURCHASING THE SL-1522 LED WORK LIGHT.
SAVE THESE INSTRUCTIONS.
PLEASE READ THESE INSTRUCTIONS BEFORE USING YOUR WORK LIGHT.
SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK,
(EXPOSURE TO EXCESSIVE UV RADIATION,) OR INJURY TO PERSONS
WARNING: To reduce the risk of FIRE, ELECTRIC SHOCK OR INJURY TO
PERSONS:
Lighted lamp may become hot!
Light can be used indoor and outdoor.
Check that the sealed push button switch is in the off position before plugging in the
work light
Connect light to 120Volt, 60 Hz power source only.
Do not touch hot lens, or enclosure.
Do not remain in light if skin feels warm.
Do not look directly at lighted lamp, or direct the light at other persons.
Keep lamp away from flammable materials.
ASSEMBLY - PLEASE REFER TO THE ILLUSTRATIONS
SETTING UP THE WORK LIGHT
OPENING THE TRIPOD LEG SET
Fully unfold the Tripod Leg Set and slide the Center Collar down until it locks into
place.
WARNING: Do NOT attempt to use the Tripod Leg Set unless the legs are fully
extended and locked into place. This is the ONLY position that the leg set can
be used in.
CLOSING THE TRIPOD LEG SET
Press the RED Release Button on the side of the Center Collar and then raise the
Center Collar up until the Tripod Let Set is fully retracted.
ADJUSTING THE COLUMN SECTIONS
The tripod has two adjustable sections of the column that can be used to customize
the working height of the Work Light. Each section is locked into place by means of a
Cam Lock Lever. To adjust the height of either section, release the Cam Lock Lever
for that section, extend the column to the desired length and the re-lock the Cam Lock
Lever.
REMOVING THE CONVERTIBLE LIGHT HEAD FROM THE TRIPOD
The SL-1522 is designed so that the entire Light Head can be removed from the
tripod. To remove the Light Head, grasp the Padded Light Handle with one hand,
squeeze together the Light Head Release Clip Tabs and pull up on the Padded Light
Handle.
INSTALLING THE CONVERTIBLE LIGHT HEAD ON TO THE TRIPOD
CAUTION: Before installing the Light Head on to the Tripod, be certain that the
INSTALLING THE CARRY HANDLE
Using a #2 Phillips Screwdriver and the 2
included short screws, attach the Carry Handle to
the Light Stand.
CAUTION: Hand-tighten only. Do not overtighten
or use an electric or battery-powered Drill Driver.
Doing so may cause damage to the unit or the
screws.
INSTALLING THE LIGHT HEADS
Align the center hole in the bracket of each of
the Light Heads with the corresponding hole in the
Light Stand.
Using the included thumb screws, tighten until
finger tight. Do this for both Light Heads.
CAUTION: Do not use any tools to tighten the
thumb screw. Finger tight is all that is required.
Overtightening may cause damage to the unit.
INSTALLING THE “Y” SPLITTER
Using a #2 Phillips Screwdriver and the included
long screw, attach the “Y” Splitter on the Power
Cord to the back of the Carry Handle.
CAUTION: Hand-tighten only. Do not overtighten
or use an electric or battery-powered Drill Driver.
Doing so may cause damage to the unit or the
screw.

Leg Set is fully extended and locked in place and that both of the two column
Cam Lock Levers are securely locked.
To install the Light Head on to the Tripod, simply line up the Locking Alignment Pin
on the bottom of the Light Head Stand with the hole in the top of the Tripod Column.
Then simply press down until the Light Head locks into place. Be certain that the
Light Head is locked into the Tripod Column before letting go of the Light Head.
OPERATION
The SL-1522 has a two sealed push button switches. One located on the back of
each of the two light heads. This provides for independent use of each of the lights.
TURNING THE LIGHT ON:
Press and release one or both of the push button switches.
TURNING THE LIGHT OFF:
Press and release the push button switch for the light that is to be turned off.
WARRANTY
1 YEAR LIMITED WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship
and materials to the original purchaser for one (1) year from the date of purchase, and
includes the LEDs, housing, lenses, electronics, switches, rechargeable batteries and
chargers. Bulbs (other than LEDs) are covered for ninety (90) days from the date of
purchase. Disposable non-rechargeable batteries are excluded from this warranty.
Normal wear and failures which are caused by accidents, misuse, abuse, faulty
installation and lightning damage are also excluded.
Consequential damages, incidental damages or incidental expenses, including
damage to property are also not covered under this warranty. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal
rights, which may vary from state to state.
IN NO EVENT WILL BAYCO PRODUCTS, INC. OR ITS AFFILIATES OR
SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND REGARDLESS OF THE FORM OF
ACTION, WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT
LIABILITY OR OTHERWISE. THE TOTAL CUMULATIVE LIABILITY TO CUSTOMER,
FROM ALL CAUSES OF ACTION AND ALL THEORIES OF LIABILITY, WILL BE
LIMITED TO AND WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT
PAID BY CUSTOMER.
If this product is used for rental purposes, the warranty term is reduced to 90 days
from the date of purchase.
WARRANTY CLAIMS – USA
Return the product to the place of purchase for all warranty related issues. If this
is not possible, contact Bayco Customer Service for a Return Goods Authorization
(RGA). Do not return this product to Bayco without fi rst receiving an RGA Number
from Bayco Customer Service. When returning the product, the RGA Number must
be written on the outside of the shipping box.
WARRANTY CLAIMS – OUTSIDE OF USA
Return the product to the place where purchased for all warranty related issues.
EXTENT OF COVERED WARRANTY WORK
Bayco will repair or replace this product at our option. If it is determined that the
warranty is no longer in effect, Bayco will contact you with a repair estimate before
beginning any work.
WARRANTY QUESTIONS
If you have any questions about this warranty or any other Bayco product
inquiries, please contact Bayco Customer Service.

BAYCO PRODUCTS LIMITED 1-YEAR WARRANTY
WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship and materials to
the original purchaser for one (1) year from the date of purchase, and includes the LEDs, housing, lenses,
electronics, switches, rechargeable batteries and chargers. Bulbs (other than LEDs) are covered for ninety
(90) days from the date of purchase. Disposable non-rechargeable batteries are excluded from this warranty.
Normal wear and failures which are caused by accidents, misuse, abuse, faulty installation and lightning
damage are also excluded.
Consequential damages, incidental damages or incidental expenses, including damage to property are
also not covered under this warranty. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you
specific legal rights, which may vary from state to state.
IN NO EVENT WILL BAYCO PRODUCTS, INC. OR ITS AFFILIATES OR SUPPLIERS BE LIABLE FOR
ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND REGARDLESS
OF THE FORM OF ACTION, WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT
LIABILITY OR OTHERWISE. THE TOTAL CUMULATIVE LIABILITY TO CUSTOMER, FROM ALL CAUSES
OF ACTION AND ALL THEORIES OF LIABILITY, WILL BE LIMITED TO AND WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT PAID BY CUSTOMER.
If this product is used for rental purposes, the warranty term is reduced to 90 days from the date of
purchase.
WARRANTY CLAIMS – USA
Return the product to the place of purchase for all warranty related issues. If this is not possible, contact
Bayco Customer Service for a Return Goods Authorization (RGA). Do not return this product to Bayco without
first receiving an RGA Number from Bayco Customer Service. When returning the product, the RGA Number
must be written on the outside of the shipping box.
WARRANTY CLAIMS – OUTSIDE OF USA
Return the product to the place where purchased for all warranty related issues.
EXTENT OF COVERED WARRANTY WORK
Bayco will repair or replace this product at our option. If it is determined that the warranty is no longer in
effect, Bayco will contact you with a repair estimate before beginning any work.
WARRANTY QUESTIONS
If you have any questions about this warranty or any other Bayco product inquiries, please contact
Bayco Customer Service.