Fluke Y5537A User manual

PN 104478 January 1995 Rev. 5, 11/18
1995-2018 Fluke Corporation. All rights reserved. Product names are trademarks of their respective companies.
Instruction Sheet
Y5537A
Rack Mount Kit
Introduction
The Y5537A Rack Mount Kit Instruction Sheet provides instructions for mounting the 5500A Multi-Product
Calibrator, 268XA Data Acquisition/Data Logging System, and 6100A Electrical power standard in a standard
19.12-inch, panel opening, E.I.A. universal spacing equipment rack.
Preparation
Before installing the rack mount kit, remove the top and bottom screws from the sides of the handles on the front of
the device. Leave the center screws installed. Remove the plastic filler strips from the sides of the device by prying
one end of each strip free using a screw driver.
Installation
To install the Rack Mount Kit, proceed as follows:
1. Attach the rack ears to the device using two M4 x 16 mm or #8-32 x 1/2-inch pan-head screws for each ear
(Figure 1).
2. Install the filler bars on the sides of the device using two #8-32 x 1/4-inch truss-head screws per bar (Figure 1).
Make sure that the hole closest to the end of the filler bar is toward the front of the device.
3. Attach the slide rails to the filler bars using three #8-32 x 1/4-inch truss-head machine screws per rail (Figure 1).
Mount the slide rail to the center row of holes on the filler bar.
4. Install the front slide brackets (shorter pair) to the rack mounting rails (Figure 2). Refer to Figure 3 for typical
mounting locations. If your rack has threaded mounting rails, use two #10-32 x 1/2-inch truss-head screws
(Figure 2, Detail A). If your rack has unthreaded mounting holes, use two #10-24 x 1/2-inch truss-head screws
and two #10-24 U-nuts (Figure 2, Detail B).
5. Install the rear slide brackets (longer pair) to the equipment rack mounting brackets as described in step 4.
6. Attach the slides to the front brackets using two #8-32 x 1/2-inch pan-head screws, two #8 flat washers, two #8
lock washers, and two #8 hex nuts (Figure 2). Align the access hole in the slide by moving the slide in and out as
necessary to access the screw heads.
7. Fully extend the slides to access the screw-heads and attach the slides to the rear brackets as described in step 6.
8. Plug the device onto the slide, unlock the slides and push the device into the rack.
9. Secure the device to the rack by fastening the rack ears to the mounting rails with two #10-32 x 3/4-inch
decorative-head screws per ear. If your rack has unthreaded mounting rails, install two #10-32 U-nuts in
appropriate places on the rail holes.

Y5537A
Instruction Sheet
2
Rack Ears
Filler Bar
#8-32 x 1/4
Truss Head
Slide Rail
#8-32 x 1/4"
Truss Head
#8-32 x 1/2" or
M4 x 16mm Panhead
80 Amp Option
if fitted
abf01f.eps
Figure 1. Attaching Hardware to the Device
abf02f.tif
Figure 2. Installing Rack Slides

Y5537A
Instruction Sheet
3
.50
.625
.625
.50
.625
.625
.625
.625
.50
.625
.625
.50
.625
.625
.50
.625
.625
.50
.625
.625
Equipment Mounting Rail
5500A Rack Ear
5500A Rack Ear mounting
hole to Equipment Rack
(2 Places)
Slide Bracket
Slide Bracket mounting for
5500A to Equipment Rack
(4 places)
.50
.625
.625
.50
.625
.625
.625
.625
.50
.625
.625
.50
.625
.625
.50
.625
.625
.50
.625
.625
Equipment Mounting Rail
5500A 268XA/6100A
268XA/6100A Rack Ear
268XA/6100A Rack Ear
mounting hole to Equipment Rack
(2 Places)
Slide Bracket
Slide Bracket mounting for
268XA/6100A to Equipment Rack
(4 places)
268XA/6100A Rack Ear
mounting hole to Equipment Rack
(2 Places)
5500A Rack Ear mounting
hole to Equipment Rack
(2 Places)
abf03f.eps
Figure 3. Typical 5500A Mounting Locations
abf04f.tif
Figure 4. Screw Identification

Y5537A
Instruction Sheet
2