Bazooka TA850C User manual

How
to install
the
FAST-9999
with
the
FAST-BTAH: The
FAST-9999
universal harness uses
the
patented Posi-Tap
connectorfrom Posi-Products for making
FAST
secure connections
to
your
OEM
wire harness.
Modo
de instalaci6n del FAST-9999 con
el
FAST-BTAH:
El
arnes universal FAST-9999
usa
el conector
patentado
Posi-
Tap de
Posi
-Products para hacer conexiones seguras de
FAST
a
su
arnes alambrico del fabricante del
equipo
original
(OEM)
.
Co
mment
installer le FAST-9999 avec le FAST-BTAH:
Le
FAST-9999
est un harnais universe!
qui
s'installe avec le
connec
teur
brevete Posi-Tap,
pour
une
installation securitaire avec
les
filages d'origine du vehicule.
Disconnect negative
battery
clamp from battery.
For easiest installation remove
the
radio and
disconnect
the
harness
from
the
back
of
the radio.
Desconecte
Ia
presilla de baterfa negati
va
de
Ia
baterfa.
Para
facilitar aun mas
Ia
instalacion,
remueva
Ia
radio y desconecte
el
arnes de atras de
Ia
radio.
Deconnecter le pole
negatif
de
Ia
batteri
e.
Pour
une installation plus facile,
en
lever Ia radio et
deconnecter le harnais
a
l'arriere du radio.
Re
d
(+
) 12V Power. Turns on when
ignition/accessory
is
on.
Blu
e/
Wh
iteTurns on remote
acces
sories (amplifiers, etc.).
If
there isno Re
mote
Amplifier
wire, you
can
often use
the
power
an
t
en
na
wire.
White(
+) Left Front Speaker
White/Black(-) Left Front Speaker
Gr
a
y(+)
Ri
ght
Front Speaker
G
ra
y/
Black(-) Right Front Speaker
Connect
the
Posi-Tap connectors
to
the corresponding wires
of
your r
ad
io harness. Consult
your car or radio manufacturer's
manual
to
get
the correct color
codesfor your vehicle.
Rojo (+) 12V de corriente.
Se
enciende
cuando
se
arranca
el
vehfculo o
se
enciende
el
accesorio.
Azul/Blanco Enciende los accesorios
remotes (amplificadores, etcetera)
Si
no hay alambre de Amplificador Remote,
en muchos cases puede usar
el
alambre de
Ia
antena electrica.
Blanco(+) Parlante delantero izquierdo
Blanco/Negro(-) Parlante delantero
izquierdo
Gris (+) Parlante delantero derecho
Gris/Negro
(-)
Parlante delantero derecho
Conecte los conectores Posi-Tap a los
alambres correspondientes de
su
arnes de
radio.Consulte
el
manual del fabricante
de
su
automovil o radio para
obtener
los
codigos de color correctos para
su
vehfculo.
Remove
the
top
cap. Place
the
wire
that
is
going
to
be tapped.
In
the
grove
of
the
cap
as
far
down
as
it
will go.
Remueva
Ia
tapa superior.
Coloque
el
alambre a
ser
conectado
en
Ia
ranura de
Ia
tapa los mas
profunda
posible.
En
lever le capuchon du
connecteur. Placer le til dans
Ia
fente du capuchon le plus
profondement
possible.
L'alimentation
rouge(+)
12V fonctionne
quand l'accessoire est activee.
Le
signal Bleu/Bianc active
les
accessoires
a
distance (amplificateur, etc.).
S'il
n'y a
pas
de signal (remote), vous pouvez utili
ser
le til d'alimentation d'antenne.
Blanc(+) Haut-parleur avant gauche
positif
Blanc/Nair(-) Haut-parleur avant gauche
negatif
Gris (+) Haut-parleur avant
droit
positif
Gris/Noir
(-)
Haut-parleur avant
droit
negat
if
Connecter
Ia
prise
Posi-Tap
au
til
correspondant
au
harnais de votre radio.
Consulter le manuel du manufacturier de
votre radio ou de votre auto pour connaltre
les bons codes de couleur.
Make sure
not
to
cross
thread
the
cap
when
screwing
it
back in place.
Cerciorese de no forzar
Ia
rosca con
Ia
tapa
al
roscarla de nuevo.
Veiller ane pas croiser
le til dans le capuchon
en
le vissant.

Continue to thread until
the cap is tight and the
wire is pierced.
Make sure
to attach all 6
of the FAST-9999 harness
wires
to your OEM harness.
Siga roscando hasta que
Ia tapa quede tensa y el
alambre perforado.
Siga roscando hasta que
Ia tapa quede ten say el
alambre perforado.
Continuer a
Visser le
capuchon jusqu'a
ce qu'il
soit bien serre
et que le til
soit perce.
Attacher chacun des 6 fils
du harnais
FAST-9999 a
votre harnais d'origine.
/
14-pin connector to the Bazooka
Conector de 14 espigas a Ia Bazooka
14-connecteur pin le Bazooka
Make sure
the end with the 6 pin Molex connectors is toward
the radio. Run the BTAH harness behind radio, dash and along
the edge of the vehicle until you get to the place you have
decided
to mount the tube .
Cerci6rese de que
el cabo de los conectores Molex de 6 espigas
quede orientado hacia
Ia radio. Pase el arnes BTAH detras de Ia
radio, el tablero y por el borde del vehfculo hasta que a lea nee
ellugar donde ha decidido montar el tuba.
Assurez-vous que l'extremite du connecteur Molex a 6 brins
so it bien fixee au radio. Passer le til du harnais BTAH derriere Ia
radio, le tableau de bard et le long du vehicule jusqu'a l' endroit
ou vous avez decide d'installer le tube .
Plug
the FAST-9999 harness into the FAST-BTAH. Mount
grounding ring and plug the 14 pin connector into the BASS
TUBE. For more information on placement and mounting, consult
your amplified
tube instruction manual.
Conecte
el arnes FAST-9999 en el FAST-BTAH. Monte el anillo
de conexi6n atierra y conecte
al conector de 14 espigas en el
TUBO DE BAJO. Para mayor informacion sabre Ia colocaci6n y
el montaje, consulte su manual de instrucciones para el tuba
amplificado.
Branchez le harnais
FAST-9999 au FAST-BTAH. Fixer Ia mise a
Ia terre et installer le connecteur a 14 brins dans leTube de
basse. Pour plus d'informations concernant !'emplacement
et !'installation, consulter le livre d'instructions devotre
amplificateur.
Ground to chassis of vehicle
~ Conectar a tierra en el chasis del vehicul
Connectez-vous a
terre sur le chassis vehicule
Posi-Tap™ Patent# 5,228,875 5,695369 5,868,589 6,692,313 Jap 2881414, Aus 708700,Tia 103534,
Can 2204826
Mex 200626 Korea 477279, China Z1971 05562.9 &others pending.
Posi-Tap™ No. de Patente 5,228,875 5,695369 5,868.589 6.692,313 Jap 2881414, Aus 708700,Tia 103534,
Can 2204826 Mex 200626 Corea 477279, China Z1971 05562.9 y otros pendientes.
Posi-TapTM Patent No. 5,228,875 5,695369 5,868.589 6.692,313 Jap 2881414, Aus 708700,Tia 103534,
Can 2204826. Mex 200626. Coree 477279. Chine et d'autres Z1971 05562.9 susoens.

~ • MODELS • MODELE N° • MODELO: TA850C BTA850FH

Dear Friend,
Thank you
for
selecting Bazooka® subwoofer speaker
systems
for
your
stereo system. Today,
the
Bazooka represents Bazooka
Mobile
Audio's
continued commitment
to
efficiency and design. An Jnnovative
manufacturing process developed by
SAS®
for
the
Bazooka provides
consumers
with
state-of-the-art speaker system design.
At
SAS,
wetake pride in manufacturing the most revolutionary
bass
speaker
systems
ever created, featuring
our
patented
Bass
Tubes®
enclosure design,
and
we
hope you
will
take pride in
owning
them.
Several years ago,
we
realized
that
efficiency was
the
wave
of
the
future
in Autosound,
so
we
made a commitment
to
design, manufacture, and
deliver
the
most efficient speaker
systems
possible.
Today
we
market
our
patented speaker
systems
worldwide
and
the
high
quality
of
the
Bazooka brand
is
well respected by consumers and dealers
of
all nationalities.
When properly installed, Bazooka subwoofer speaker
systems
will
give
you years
of
clean uninterrupted sound reproduction. Therefore, I urge
you
to
take a
few
minutes
of
your
time
to
review this instruction booklet.
It
was designed
to
give you a better understanding
of
our
products and
to
explain
how
to
apply
them
properly.
Thank you again
for
choosing Bazookas. Our early commitment
to
quality
has
made
them
the
product
of
choice, and I am sure you
will
agree
that
you have made
the
right
one! Enjoy!
Sincerely,
JON
C.
JORDAN
President
SAS/BAZOOKA
1

CONTENTS
HELPFUL HINTS BEFORE YOU BEGIN
PG3
VEHICLE PLACEMENT RECOMMENDATIONS
PG4
MOUNTING
THE BAZOOKA
PG 5-7
WIRING DIAGRAM PG8
SPECIFICATIONS
PG9
WIRING
PG 10-12
TROUBLESHOOTING
PG 13-14
WARRANTY
PG 15-16
2

HELPFUL
HINTS-BEFORE
YOU
BEGIN
Please
take
time
to
read
through
this
manual
and
plan
out
your
installation
before
you
begin!
Locate an area in
the
rear
of
the
vehicle
where
you
would
like
to
place
the
Bazooka speaker systems. The location you have selected must
meet
the
following
requirements in order
for
the
Bazooka
to
be properly
installed in
the
vehicle:
1)
The
woofer
(grill end) should be facing
into
a corner.
(See
vehicle placement recommendations on
p_g.
5-6)
2)
Ideally,
there
should be 2
to
4
inches
between
the
woofer
and
the
corner
it
is
pointing
into.
3)
The
mounting
area should be carefully checked
to
be sure
that
the
mounting
screws
will
not
damage
the
gas
tank,
electrical
wiring,
fuel
lines,
or
the
spare
tire
during
the
mounting
of
the
strap
bases.
4)
The strap
mounting
bases
should be screwed securely
to
a
rigid surface
that
is
part
of,
or
anchored
to,
the
structure
of
the
vehicle.
3

VEHICLE
PLACEMENT
RECOMMENDATIONS
TRUCK
INSTALLATION
tube
size
is
exaggerated
for
emphasis
HATCHBACK
INSTALLATION
tube
size
is
exaggerated
for
emphasis
SEDAN
INSTALLATION
tube
size
is
exaggerated
for
emphasis
4

MOUNTING THE BAZOOKA
Logo
should
face up
Figure 1
1. With the topside of the buckle facing up (see figure 1 ), lace the strap
through the mounting base as illustrated in figure 2
c[tY__.~~F-ig-ure--.2 ·- ~
r r
I I
2. After the strap is completely laced through the mounting base, make
a
loop with the strap, where it runs across the middle of the base as
illustrated in figure 3. This loop is necessary to access the two mounting
holes in the base.
5

Figure 4
3.
Place each
mounting
base
under
the
Bass
Tubes®
enclosure
so
that
the
apex
at
the
bottom
of
the
tube
sits inside
the
mounting
base
as
in
figure
4.
I
I
~--------------
---------,
/ I
I I I
I I
--
,
-------------------------
--{
'
,,
I
I ' I
I 1 I
I
I
I
I
I
I
I
I I
\.
I I I
.......
- - - -
-
-
-
-
- - - - - - -
-
- - - - - - -
-
~
...
-
,_
,
Figure 5
4.
Move
the
bases
so
that
they
are spaced approximately
3"
from
each
end
of
the
enclosure
as
illustrated
in
figure
5.
5.
Remove
the
Bass
Tubes®
enclosure
without
moving
the
mounting
bases and set
it
aside.
6.
Screw each
mounting
base securely in place
with
screws
provided
as
illustrated
in
figure
3.
6

See Model Size
I·
For
Length
·I
1.
Remove
any
slack
in
the
strap
by
feeding
it
out
of
the
mounting
base
on
the
loose
end
of
the
strap
opposite
the
buckle.
8.
Place
the
Bass
Tubes®enclosure
on
the
mounting
bases
and
fasten
the
buckles
as
illustrated
in
figure
7.
The strap
should
loop
through
the
buckle
and
be
tightened
securely
by
holding
the
strap in place
with
one
hand
and
pulling
the
loose
end
away
from
the
buckle,
but
against
the
cabinet
.
Figure 7
Technical
Note:
Model
6"
8"
10"
Length
17"
22"
27"
Due
to
the
jarring
and
shifting
that
can occur in a vehicle,
the
mounting
straps may stretch
or
loosen.
We
recommend
that
you
check
the
straps
regularly
to
assure
that
your
Bass
Tubes®
enclosure
is
mounted
securely
in
place.
7

TABSOC WIRING DIAGRAM
QUICK
DISCONNECT
YELLOW ON/OFF
JUMPER LOOP
NOTE:
GN/TRACE
HI·LEY
INPUT(-)
GRAY/TRACE
HI· LEV
INPUT(-)
GREEN
HI·LEV
INPUT(+)
16 GAUGE
BLACK CHASSIS
GROUND
16 GAUGE RED
BAnERY (12¥+)
ORANGE
REMOTE
RCA
PHONO PLUGS
Right & left low
level Inputs
REMOVE AUTO TURN-ON LOOP TO USE ORANGEREMOTE
WIRE FOR
NORMAL REMOTE TURN-ON
8
Remote Turn-On is
Actually Blue/White
The GN & GN/TRACE wires shown
are actually WHITE & WHITE/TRACE

SPECIFICATIONS
RMS
Output
power
Rating
4
Ohm@
14.4V@1 %THO
22*
2
Ohm@
14.4V@1%THD 45
Frequency
Response
3 dB
21
Hz-85Hz
SIN
Ratio
(dba)
1W
>70
THD
with
A-Weight
filter
4
Ohm
per
Channel
0.23o/o
2
Ohm
per
Channel
0.43o/o
Protection
(DC,
Short,
Thermal,
Overload)
Yes
*Not applicable to the TA850C & BTA850FH TA850C & BTA850FH are 2 Ohm products
9

DO NOT substitute the fuse included with the Amplified Bazooka
subwoofer with anything other than the SAME fast blow current
rated fuse. Substitution or deletion will void the product•s warranty
and may cause damage to your car or the amplifier.
SHOULD I USE HIGH OR LOW LEVEL INPUTS?
If the source unit has only speaker outputs, use the high-level inputs
of the Amplified Bazooka subwoofer. If the source unit has both high
and low level outputs, we recommend using the high level inputs
over the low level inputs, due to the configuration of the Amplified
Bazooka subwoofer•s balanced input circuit. Not all head units, even
those
that promise high output voltage in their marketing materials,
indeed have
high-voltage RCA outputs. Because of this, Bazooka
Mobile Audio recommends using the speaker level inputs when in
doubt-they will always provide sufficient drive level to the amplifier.
PLEASE NOTE THAT THE WIRING IN A FACTORY STEREO MAY NOT BE
ELECTRICALLY IN PHASE EVEN WHEN YOU HAVE MADE THE PROPER
CONNECTIONS.
Take
the time after you make your wire connections to run through
the quick phase check procedure in the "AM I IN PHASE?" section at
the end of this manual, and NEVER USE BOTH high and low-level
inputs at the same time!
INPUT SIGNAL CONNECTIONS
High-Level Inputs:
If the source unit has both front and rear speaker outputs, use
only one set of speaker outputs for the high-level input of the
Amplified Bazooka. Connect the GREEN wire from the 14-pin
Molex plug of the Amplified Bazooka subwoofer to the source
units left(+) positive speaker output. Connect the GREEN W/BLACK
stripe wire of the plug to the source units left(-) negative speaker
output. Connect the GRAY wire of the plug to the source units
right(+) positive speaker output. Connect the GRAY W/BLACK
stripe wire of the plug to the source units right(-) negative speaker
output. When using high-level inputs, take the time after you
make all wiring connections to run through the AM I IN PHASE
procedure at the end of this manual to confirm that your inputs
are in correct electrical phase and the proper bass response is
being produced.
10

Low-Level Inputs:
If your source unit only has low-level RCA phono jack output, use only
the low-level inputs of the Amplified Bazooka. Connect the low-level
RCA phono jack inputs of the Amplified Bazooka subwoofer to the
source with a shielded RCA patch cord. To avoid possible noise
problems, be sure
to run the patch cord away from all power wires
and
factory wire harnesses. When using the low-level inputs DO NOT
make any connections
to the Green and Gray high-level input wires
of the Amplified Bazooka subwoofer and make sure these wires are
insulated
to avoid the possibility of a short circuit.
POWER WIRE
The power wire must be fused and connected directly to the positive
terminal of the battery to provide a power source with a low voltage
drop and low noise. Do not make the power connection at the fuse
block
or any point other than the battery. Improper power sources
can reduce
output and cause distortion.
The fuse holder should be connected to the battery•s positive terminal.
The fuse
is designed to prevent fire or damage to your car, should
the battery wire short to ground. Wait to insert the fuse into its holder
until all wire connections have been made.
If it is necessary to lengthen the battery wire, add the required length
between the amplifier and the fuse holder, not the fuse holder and
the battery. If you need to extend t he battery wire, use 16 gauge
or larger for all A100, and 12 gauge or larger for all A200 models. It
is best to use as short a wire as possible. Be sure you DO NOT run the
power wire next to the input cables of the amplifier this will induce
noise. Avoid
running the power wire near the radio•s antenna or
power leads, or near sensitive equipment or harnesses. The power
wire carries substantial currents and could induce noise.
GROUND WIRE
The ground wire must be connected directly to the vehicle chassis
near
the amplifier. We do not recommend extending the ground wire
in any installation, as this can cause unwanted ground loops.
The
ground point in the car should be a piece of chassis metal that
is part of or welded to the main body of the vehicle. Painted surfaces
should be scraped
or sanded clean to expose the bare metal before
the ground lug is bolted down. (Cover the bare metal area with paint
or grease after you finish mounting the ground wire to prevent rust.)
11

REMOTE
TURN
ON
OPTIONS
OPTION
ONE:
When
you
are
using
this
option
with
all
amplified
Bass Tubes®
models:
For
the
most
versatility
the
Orange
Remote Turn On
Wire
should be connected
to
the
source unit•s
..
Accessory
..
,
..
Auto-Antenna
..
or
..
Remote
..
lead--
any
of
which
will
supply 12 Volts positive
when
the
source
is
turned
on.
OPTION
TWO:
When
you
are
using
this
option
If
the
source does
not
have an
Auto-Antenna
lead
{or
if
the
Auto-
Antenna
goes
down
during
tape
operation),
you
can
connect
the
Amplified
Bazookas· Remote Turn On
Wire
to
an accessory
or
ignition
point
at
the
vehicle fuse block. In
this
configuration,
the
Amplified
Bazooka
subwoofer
will
be
on
whenever
the
ignition
is
on. This
method
may
allow
noise
or
turn-on-and-off
transients
to
become
amplified
when
the
source
unit
is
not
in use,
and
therefore
is
a
less
desirable
than
option
one. Locate
the
Auto/Off
Jumper
Loop located
on
the
wiring
harness;
SAS
ships
the
Amplified
Bazooka
subwoofer
with
this
Jumper
in
the
ON
Position. The Quick Disconnect YELLOW
On/Off
Jumper
Loop
must
be
plugged
into
the
harness.
12

TROUBLESHOOTING
Am I In Phase?
If your inputs are out of phase and you turn the balance
control of your radio all the way to one side, right or left, the
bass output from the Bazooka® will increase. When you bring
the balance control back to the center position the bass level
will drop. This confirms that one of your input channels is
wired out of phase with the other.
When one of the Amplified Bazooka·s High-level Input channels
is out of phase electrically with the other High-level Input
channel, your Bazooka will sound as if it has little or no output
and any output that is produced may sound distorted. If you
suspect that your Bazooka is out of phase, use the AM I IN
PHASE procedure to diagnose and correct the Bazookas· output,
and proper bass response will be produced. channels is wired
out of phase with the other. To correct this situation, simply
flip the phase switch on the amplified Bazooka®. When the
input signal is in correct electrical phase, the level of bass
output will be greatest when the balance control of the radio
is set to the center position.
Do You Have A Phase Problem?
If the bass response in your application appears to be lower
then you expected or sounds muffled and or distorted, you
may be experiencing Phase Cancellation.
Phase Cancellation
When two speakers in the same frequency range produce
sound waves that are inverted from one another or 180° out
of phase, the sound waves will cancel each other out to some
degree. This effect will be heard as a drop in the output level
and/or a muffled or muddy quality in the Bass Response. The
source
of this Phase Cancellation can be at any point in the
signal path. The obvious cause of this problem would be a
speaker connection that was reversed in polarity, but that is
not always the case. Sometimes amplifier channels will shift
phase 180° for no good reason, or a signal processor could
have a setting for phase that has been set incorrectly or the
13

source material could just be recorded in error. Also speaker
placement and the acoustics of the listening environment can
effect the phase. No matter what or where the cause is located,
the solution is an easy one.
PHASE CORRECTING PROCEDURE
Disconnect all but one Bazooka® from your system. Be sure
that any loose wire connections are insulated to avoid the
chance of short-circuiting any of the electronic equipment.
Listen to the system and take note of the level of the Bass
Response. Connect the next Bazooka® and compare the level
of the combined output to that of the single unit. If the Bass
Response increases, the Phasing is correct and you can repeat
this process on the next Bazooka. If the level of the Bass
Response drops, the Phasing is incorrect and you should reverse
the speaker connections to this Bazooka® and compare again.
In
short to INCREASE IS GOOD, to DECREASE IS BAD! Using
this method, any number of Bazooka® subwoofers can be kept
in absolute phase.
PRACTICE SAFE LISTENING
Continuous exposure to high volumes of sound may cause
permanent hearing loss. High-powered auto sound systems
are capable
of producing sounds well over 130 dB. Even short
periods of play at high volume levels can impair your ability
to hear necessary traffic sounds and may constitute a hazard.
Please use
common sense and practice SAFE LISTENING!
14

LIMITED WARRANTY (UNITED
STATES)
Southern
Audio
Services, Inc.,
warrants all products
to
be free
from
defects
in material and workmanship
for
a period
of
one
(1)
year
from
the
date
of
purchase.
In
the
event
the
produd
is
not
as
warranted,
SAS'
sole
obligation
shall
be
to
repair
or
replace
the
defedive
produd
at
SAS'
option:
SAS
limits
its
obligation
under
any
implied
warranties
under
state
laws
to
a
period
not
to
exceed
the
limited
warranty
period.
SAS
and
its
authorized
BAZOOKA®
dealers
specifically
disclaim
liability
for
any
incidental
or
consequential
damages.
Some
states
to
not
allow
limitations
on
how
long
an
implied
warranty
lasts,
and
some
states
do
not
allow
the
exclusion
or
limitation
of
incidental
or
consequential
damages,
so
the
above
limitation
or
exclusions
may
not
apply
to
you.
This
warranty
gives
you
specific
legal
rights,
and
you
may
have
other
rights,
which
vary
from
state
to
state.
What
is
covered:
This
warranty
covers all defects in materials
or
workmanship (parts and labor) in
the
product.
What
is
not
covered:
This
warranty
does
not
cover
the
following:
1.
Damages occurring
during
shipment
of
the
product
to
SAS
for
repair (claims
must be presented
to
the
carrier).
2.
Damages caused by accident, abuse, negligence, misuse
or
improper
operation
or
installation.
3.
Damages caused by an act
of
God, including
without
limitation,
fire, flood,
storms,
or
other
acts
of
nature.
4.
Any product, which
has
a serial number, defaced, altered, modified,
or
removed.
5.
Any
product
that
has
been altered
or
modified
without
SAS'
consent.
How
to
obtain
warranty
services:
1.
You are responsible
for
delivery
of
the
product
to
an authorized BAZOOKA®
dealer
or
contact
SAS
at
1-800-THE
TUBE
for
a Return
Authorization
number.
The Return
Authorization
number
must be clearly
written
on
the
outside
of
the
box. Freight must be prepaid
to
SAS.
Warranty
replacement parts
will
be
returned
freight
prepaid. The entire enclosure may be returned
for
warranty
service,
but
return
will
be
freight
collect.
2.
You must provide
proof
of
the
date
of
purchase
of
the
product.
If
proof
of
purchase
is
not
provided, original date
of
manufacture
will
be
used
to
determine
warranty
period.
3.
You must package
the
product
securely
to
avoid damage
during
shipment.
4.
After
acquiring a Return
Authorization
number, ship
to
the
address below.
15

PLEASE
RETURN
THIS
PORTION
IMMEDIATELY
MODEL#
SERIAL#
PURCHASE
DATE
DEALER
PURCHASED
FROM
DEALER
ADDRESS
TELEPHONE
PURCHASERS
NAME
STREET
ADDRESS
CITY
STATE
ZIP
TELEPHONE
E-MAIL
16