BE Power Equipment FSB75 COMBO User manual

PEDESTAL FAN & WALL FAN
OWNER’S MANUAL
Model: FSB75 COMBO
AIR COMPRESSOR
OPERATORS MANUAL
Version 5.1
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
FSB75 COMBO
FSB75 COMBO

Page 1
POWER EQUIPMENT
POWER EQUIPMENT
FSB75 COMBO OWNER’S MANUAL
SAFETY INSTRUCTIONS
This product is intended for indoor use only.
Always operate the product from a power source of the same voltage, frequency
and rating as indicated on the product identication plate.
To reduce the risk of electric shock, do not use this fan with any solid state speed
control device.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
Do not insert ngers or any other foreign object through the front and rear guard
and into the blade.
Close supervision is necessary when any product is used by or near children or
inrm persons. Do not allow children to use it as a toy.
Do not operate any product with a damaged cord or plug, after the product
malfunctions, is dropped or appears damaged in any way. Return the complete
product to the place of purchase for inspection, repair or replacement.
To reduce the risk of electric shock, do not immerse or expose the product or
exible cord to rain, moisture or any liquid.
This product should not be used in the immediate vicinity of water, such as sinks,
bathtub, washbowls, swimming pool etc. where the likelihood of immersion or
splashing could occur.
Switch off and unplug from outlet when not in use, before assembling or
disassembling parts and before cleaning. Fully assemble the fan before switching
on.
Avoid contact with moving parts. Do not insert any object through the grill when
the fan is operating.
Do not cover the grill, or operate in close proximity to curtains, etc. Always
disconnect the fan when moving it from one location to another.
The use of attachments or accessories not recommended or sold by the product
distributor may cause personal or property hazards or injuries.
Never attempt to make any modications to or repair the product yourself. Have
it repaired by a qualied person only.
Place the appliance on a at and dry surface.
Manufacturer takes no responsibility for any damage caused by incorrect use.
Precautions must be taken to avoid the back-ow of gases into the room from the
open ow of gas or other fuel-burning appliances

Page 2
POWER EQUIPMENT
POWER EQUIPMENT
FSB75 COMBO OWNER’S MANUAL
FAN DIMENSIONS
PAGE 10 PAGE 3
Pedestal
Wall

Page 3
POWER EQUIPMENT
POWER EQUIPMENT
FSB75 COMBO OWNER’S MANUAL
PEDESTAL FAN ASSEMBLY
PAGE 4 PAGE 9
1. Fit REAR GUARD of fan onto the MOTOR and
secure with 4 screws provided. Ensure screws
are tight to avoid vibration noise
2. Fit BLADE to shaft and lock blade SET
SCREW.
3. Fit FRONT GUARD to rear guard using clips
provided.
4. Fit OUTER TUBE onto CAST IRON BASE and
secure with the BOLT. Then t COVER RING
onto CAST COUPLING.
5. Screw out PLASTIC KNOB on column then t
INNER TUBE. Secure grub screw with key.
6. Fit MOTOR onto MALE SUPPORTER. Adjust to
suitable height at coupling then lock the MALE
SUPPORTER SET SCREW.
7. Secure locking screw on FEMALE SUPPORTER
for desired head angle/ tilt. To adjust the head
tilt, loosen the nut above the female support,
then re-secure the nut after adjustment.

Page 4
POWER EQUIPMENT
POWER EQUIPMENT
FSB75 COMBO OWNER’S MANUAL
WALL FAN ASSEMBLY
1. Complete points 1-3 on page 4.
2. Attach the wall mount base to the wall by drilling two holes with a M 10*80 drill
bit. Secure with the two M12 screws provided.
NOTE: Installation height should be a minimum of 2.5 metres from the ground.
IMPORTANT: Check wall is suitable for mounting and supporting the wall fan.
3. Insert the BEND TUBE through the two “U” shape slots provided in the wall
mount base & lock them into position using the two screws provided.
NOTE: The Bend tube can be positioned either upwards or downwards. You
must orient female support upward by removing the screw, repositioning &
resecuring. Never attach the fan so it is hanging below the female supporter.
PAGE 8 PAGE 5
FSB-75
FSB-75
Install the screw
Cement
Fixing
bolts
Wall
Bend Tube
Wall mount base
Washer
Spring Washer
Nut

Page 5
POWER EQUIPMENT
POWER EQUIPMENT
FSB75 COMBO OWNER’S MANUAL
4. Insert the motor into the female support and secure with the screw.
PAGE 6 PAGE 7
5. Secure locking screw on FEMALE SUPPORTER for desired head angle/ tilt. To
adjust the head tilt, loosen the nut above the female support, then re-secure
the nut after adjustment.
WARNING! Make sure all parts are assembled correctly and connections are tight.
WARN ING! If supply cable to too tight the oscillating motion can cause damage -
ensure sufcient section of cable to avoid damage.
ENVIRONMENT OF USE
1. The max relative humidity is 90%(when in 25°C);
2. Below 1000 metres altitude.
FEMALE SUPPORTER
FAN HEAD
LOCATING SCREW

Page 6
POWER EQUIPMENT
POWER EQUIPMENT
FSB75 COMBO OWNER’S MANUAL
OPERATION
1. Make sure the Fans voltage is in accordance with local voltage before use.
2. The fan is recommended for use in ordinary indoor situations, but not at high
humidity.
3. To turn on select the desired speed setting
0 - Off
1 - Slow
2 - Medium
3 - Fast
4. For xed air ow ensure the swing arm is not connected to the fan motor
5. For oscillating air ow ensure the swing arm is connected to the fan motor by
rotating the oscillating adjustment screw in an anti-clockwise direction.
6. Unplug the fan when not in use.
PAGE 6 PAGE 7

Page 7
POWER EQUIPMENT
POWER EQUIPMENT
FSB75 COMBO OWNER’S MANUAL
MAINTENANCE
1. To ensure prolonged safe use ensure you have this unit inpected, cleaned &
moving parts lubricated by a qualied person aher every 1000 hours of use.
2. Regularly inspect the cord & plug & do not use if damaged. A lisenced
electrician is required to repair or replace the cord & plug.
3. Any other repairs or maintenance must be performed by a qualied person.
SPECIFICATION
ELECTRICAL DIAGRAM
Model Description Size
(mm)
Volt
(V~)
Freq
(Hz)
Watts
(W
Air Flow
(m3/min)
FSB-75 Pedestal Fan 750 220-240 50 280 290
FSB-75 Wall Fan 750 220-240 50 280 290
The data above is for reference only and may change without notice
PAGE 8 PAGE 5
FSB-75
FSB-75

Page 8
POWER EQUIPMENT
POWER EQUIPMENT
FSB75 COMBO OWNER’S MANUAL
EXPLOSION VIEW & PARTS BREAKDOWN
PAGE 4 PAGE 9

Page 9
POWER EQUIPMENT
POWER EQUIPMENT
FSB75 COMBO OWNER’S MANUAL
EXPLOSION VIEW & PARTS BREAKDOWN
PAGE 10 PAGE 3
Pedestal
Wall

Page 10
POWER EQUIPMENT
POWER EQUIPMENT
FSB75 COMBO OWNER’S MANUAL
WARRANTY
We warrant that this product will be free from defects in materials or
workmanship for a period of 12 months from the date of purchase. The benets
conferred by this warranty are in addition to all rights and remedies which you
may be entitled to under the Australian Consumer Law, and any Other statutory
rights you may have under other applicable laws. This Warranty does not exclude,
restrict or modify any such rights or remedies.
Any claim under this warranty must be made within 12 months of the date of
purchase of the product. To make a claim under the warranty, take the product
(with proof of purchase) to the store where you purchased the product.
This Warranty is provided in addition to other rights and remedies you have
under law: Our goods come with guarantees which cannot be excluded under the
Australian Consumer Law. You are entitled to replacement or refund for a major
failure and to compensation for other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.

Distributed in Australia by
CONTACT DETAILS
B.A.R Group P/L
15 Hudson Place,
Mulgrave, NSW, Australia 2756
Phone: [phone]
www.bargroup.com.au
Distributed in New Zealand by
CONTACT DETAILS
BE Pressure Supply
541D Te Rapa Road, Te Rapa,
Hamilton 3200, New Zealand
Phone: [phone]
www.bepressure.co.nz
Errors and omissions excepted.
Specications and performance may change.
Version 5.1; 2021
AIR COMPRESSOR
OPERATORS MANUAL
Version 5.1