Beale Street Audio TIC651 User manual

Beale Street Audio
TIC651, TIC801 In Ceiling Speakers
TICW401 In Ceiling/In Wall Shallow Depth
TU401 In Ceiling/In Wall Pancake
25/70/100V Speakers
Installation Guide

2
Introduction
Congratulations and thank you for purchasing Beale Street Audio 70 Volt In
Ceiling/In Wall speakers with Sonic Vortex®.
Our patented Sonic Vortex Technology is based on Ported Transmission
Line design and incorporates a compact, integrated enclosure. Most In
Ceiling speakers do not utilize a back box, even fewer have an enclosure,
and only a Sonic Vortex speaker has an Integrated Transmission Line Ported
Enclosure. Without something behind the speaker driver the music not only
plays into the room, but also bleeds into adjoining rooms such as the attic
or an occupied room. The bleed negatively affects performance, and sound
consistency.
The Sonic Vortex enclosure directs all of the sound from the speaker driver
into the room it is intend to be in, so you get to enjoy your speakers without
disturbing the rest of the house. Great bass response, stereo image, and
big sound that you can’t get with any other in ceiling speaker.
Beale Street Audio 70V speakers install with ease using the ‘dog’ mounting
system and magnetic bezelless grilles for fast, clean installations.
The TIC and TU series 25/70/100 volt Beale Street Audio speakers offer
exceptional performance in a 70/100V system. Beale Street Audio 70/100V
speakers with Sonic Vortex really help improve overall performance and
sound quality in 70/100V systems where audio quality is sometimes not
the main focus.
Please follow the instructions in this manual to assure proper installation
and to achieve the full performance and satisfaction you would expect from
Beale Street Audio.

3
Speaker Placement
When installing in wall/in ceiling speakers, (or in wall/in ceiling anything for
that matter) it is always a good idea to find out what is in the wall/ceiling
before cutting holes. Be aware of the location of plumbing, electrical and
structural elements that may affect speaker placement.
Stereo
It is also a good idea to locate stereo speakers so they are centered to
the main listening position in which the user/s will normally be located.
Whenever possible, try to position the left and right speakers at the same
distance from each other as they are from the main listening position.
Subwoofer
Subwoofers are omni-directional so placement of in wall/in ceiling subs is
somewhat less critical, but placement can be affected (good and bad) by
corners and walls, so try to find a location that will be somewhat unaffected
by placement.
Angled
If using the ‘Angled In’ speakers, be sure to position them so the speakers
are facing into the room and directed toward the main listening position.
Surround
Locate surround speakers according to the recommendations in the
surround processor’s owner’s manual.

4
Installation
SPEAKER WIRE - 25/70/100V
When pulling wire for a 70V/100V speaker system, pull distribution lines
(each distribution line is a wire pair) in a daisy-chain pattern, (amp to first
speaker, first speaker to second speaker, second speaker to third speaker,
etc). If distributing stereo, pull individual distribution lines to each speaker
location for each pair (left/right) in a daisy chain from the amp location. Use
quality stranded speaker wire based upon the 70V Speaker Wire Gauge
Table below.
70V SPEAKER WIRE GAUGE (30W Zone Output)
SPEAKER WIRE LENGTH SPEAKER WIRE GAUGE
350’ (106m) 24 AWG
550’ (167m) 22 AWG
900’ (274m) 20 AWG
1400' (426m) 18AWG
2300' (701m) 16AWG
NEW CONSTRUCTION
Beale Street Audio speaker installation can be simplified by using a Beale
Street Audio new construction EZBracket®, (sold separately;
visit www.getbeale.com for additional information). This is installed prior to
drywall installation and allows for precise speaker placement and simplifies
the final installation of the speaker.
EXISTING CONSTRUCTION
70/100V distribution lines must be run in a daisy chain configuration from
the amplifier to the first speaker location then to the second speaker
location and so on.
• Choose a location for each speaker that is free of obstructions created
by joists, HVAC duct-work, electrical wire runs, plumbing or anything
else that might not allow for the depth of the speaker or create
interference or noise.

5
Installation
• Once you have determined your locations, use a pencil to mark the hole
to cut out for the speaker using the supplied template. Don’t forget to
allow for the size of the speaker bezel if you are installing the speaker
near a sidewall or other item that could become an obstacle.
NOTE: Round grille and square grille finish both use the same drywall
cutout.
• If you are unsure of potential obstacles, carefully cut your holes using
an angle cut to the inside of the cutout area. This will allow you to “plug”
the hole easily if needed. If the area is clear and is a good location for
the speaker, go ahead and cut the edges of the opening at 90 degrees to
accommodate the speaker diameter.
Cut hole at an angle in case patching is necessary
Save cutout for patching if necessary
Cut edge at 90°if area is clear of obstructions
• Strip the insulation on each conductor approximately 1/2” (12.7mm) and
insert to the plug in speaker terminals. Ensure that there are no stray
strands of wire protruding from the connectors that can cause shorts.
Observe proper polarity (+ to + and – to –) for each speaker and at the
amplifier. Be sure to tighten the ‘elevators’ on the plug in connector so
the wires do not come loose after installation.

6
INPUT OUTPUT
- + + -
25V
0.9
1.8
8Ω
100V
70V
7.5
15
15
X
INPUT OUTPUT
- + + -
INPUT OUTPUT
- + + -
INPUT OUTPUT
- + + -
INPUT OUTPUT
- + + -
25V
0.2
0.3
0.5
0.9
1.8
8Ω
100V
70V
1.9
3.8
3.8
7.5
7.5
15
15
1.9
1
X
INPUT OUTPUT
- + + -
Right Left
INPUT OUTPUT
- + + -
INPUT OUTPUT
- + + -
70/100V Amplifier Speaker Terminal
Left/Right 70/100V
Speaker Pair #1
Left/Right 70/100V
Speaker Pair #2
To Input on Next
70/100V Speaker
+ to +; - to -
To Input on Next
70/100V Speaker
+ to +; - to -
+ to +
- to -
Distribution Lines
(Speaker Wire)
Per Instructions In Section:
Installation/Speaker Wire
Installation

7
Installation
TAP WATTAGE
In a 70/100V system it is necessary to select tap wattage to determine
amplifier power requirements and set relative speaker volume.
25V
0.2
0.3
0.5
0.9
1.8
8Ω
100V
70V
1.9
3.8
3.8
7.5
7.5
15
15
1.9
1
X
25V
0.2
0.4
0.7
1.3
2.5
8Ω
100V
70V
2.5
5
5
10
10
20
20
2.5
1.3
X
25V
0.3
0.5
0.9
1.8
3.5
8Ω
100V
70V
3.8
7.5
7.5
15
15
30
30
3.8
1.9
X
Note the different tap settings by model.
Use the gauge on the tap that corresponds to the distribution line voltage
used for the system being configured (25V, 70V, 100V).
Add up the total tap wattage set for all of the speakers to be connected to
a 70V/100V zone and multiply by 1.2. This will provide sufficient power to
compensate for an efficiency loss of around 20% that is typical in 70/100V
systems.
8Ω
If a low impedance amplifier is going to be used, be sure to set the speaker
Tap Selector to 8Ω, and connect the amplifier speaker terminal +/- to the
INPUT +/- on one 8Ω speaker. If the amp is capable of a low impedance
load, (4Ω/2Ω) and if the speaker load is acceptable, (two 8Ω speakers, one
4Ω speaker, etc) connect the speaker(s) to the amp in parallel, (all speakers’
+ to amp +, all speakers’ - to amp -) not daisy chain as used for 70/100V.
If you’re not sure about an amplifier’s load handling capability, contact the
amplifier manufacturer’s technical support for assistance to avoid potential
major damage to the amp and speakers.
TICW401/TU401 Tap TIC651 Tap TIC801 Tap

8
Round Grille
• With the ‘dogs’ flush to the side of the speaker, insert the speaker into
the cutout and tighten each of the four screws for the speaker’s dogs,
enough to clamp the speaker to the drywall. Do not over-tighten.
0.2
0.3
0.5
0.9
1.8
8Ω
100V
70V
1.9
3.8
3.8
7.5
7.5
15
15
1.9
1
X
25V
Turn screws to extend dogs
as shown
Turn screws to extend dogs
as shown
• Attach the round grille to speaker. The grille attaches with magnets so it
will just snap into place.
Installation

9
Installation
TU401 ORIENTATION
For best results in a stereo application when using TU401 speakers, be
sure to install the left and right speakers symmetrically so the woofers and
tweeters are oriented as mirror images as shown below. This will improve
stereo imaging and overall audio performance. Orienting the woofers and
tweeters in random positions will result in less than ideal performance.
DO THIS: (Tweeters Vertical)
0.2
0.3
0.5
0.9
1.8
8Ω
100V
70V
1.9
3.8
3.8
7.5
7.5
15
15
1.9
1
X
25V
0.2
0.3
0.5
0.9
1.8
8Ω
100V
70V
1.9
3.8
3.8
7.5
7.5
15
15
1.9
1
X
25V
OR THIS: (Tweeters Horizontal)
0.2
0.3
0.5
0.9
1.8
8Ω
100V
70V
1.9
3.8
3.8
7.5
7.5
15
15
1.9
1
X
25V
0.2
0.3
0.5
0.9
1.8
8Ω
100V
70V
1.9
3.8
3.8
7.5
7.5
15
15
1.9
1
X
25V
DO NOT DO THIS:
(Tweeters in Random Positions)
0.2
0.3
0.5
0.9
1.8
8Ω
100V
70V
1.9
3.8
3.8
7.5
7.5
15
15
1.9
1
X
25V
0.2
0.3
0.5
0.9
1.8
8Ω
100V
70V
1.9
3.8
3.8
7.5
7.5
15
15
1.9
1
X
25V

10
Installation
Square Grille (Models TIC651, TICW401)
Optional square bezels/grilles are available separately. Please reference
Beale Street Audio part numbers: 4” - GS4W, (white) GS4B (black); 6.5” -
GS6.5W, (white) GS6.5B (black) when ordering.
• With the ‘dogs’ flush to the side of the speaker, insert the speaker into
the square bezel as shown.
1. Slide the Speaker into the Square Bezel 2. Assembled Speaker and Square Bezel
3. Slide the Speaker/Square Bezel into the
Drywall Cutout
4. Installed Speaker and Square Bezel

11
Installation
• With the speaker/bezel assembly installed in the wall, using a level,
square the bezel to the wall and then turn the ‘dog screws’ to secure the
speaker and bezel to the drywall.
Turn screws to extend dogs
to lock speaker and bezel
to drywall
Turn screws to extend dogs
to lock speaker and bezel
to drywall
• Attach square grille to bezel. The grille attaches with magnets so it will
just snap into place.
Adapting the Square Grille to an installed Round Speaker
• You can adapt the square bezel/grille to an installed round speaker by
cutting one of the thin sides of the bezel, loosening the dogs on the
installed speaker just enough to create a space between the speaker
and drywall and then slipping the bezel around the speaker. Square
the bezel to the wall and then tighten the ‘dog screws’ to secure the
speaker and bezel to the drywall. Install the square grille.
Pivoting Tweeter (TIC651, TIC801, TICW401)
• With the speaker installed, the tweeter can be pivoted to point directly
into the main listening area for tighter imaging of high frequency
content. Pointing the tweeter away from the main listening area will
create a more ambient sound.
Carefully press the edge of the
tweeter as shown to pivot the
tweeter to the desired position.

12
Installation
TROUBLESHOOTING
Beale Street Audio speakers are designed to function trouble-free. Most
problems that occur are due to simple issues. If you have trouble, please
check the list of simple fixes below.
SPEAKER TROUBLESHOOTING
PROBLEM SOLUTION
NO SOUND Verify that there is audio from the
source selected. Select another
source if necessary.
Ensure that the amplifier is turned
on and connected properly.
Check any connections at other
devices, such as a volume control.
Temporarily bypass the control if
needed.
Check wire connections at each
speaker not producing sound for
good contact to bare wire, not wire
insulation.
PAINTING
The grille can be painted, but go as light as possible to not to clog the fine
holes with paint. Only paint grilles when they have been removed from
the speakers and be sure to remove the cloth on the backside of the grille
before painting. If the cloth is not removed for painting, it will absorb the
paint and clog the grille, significantly affecting the sound...and not in a good
way. (We have taken great effort to eliminate any ‘color’ from the sound of
our speakers, so let’s try to keep it that way...OK?)

13
Specifications
6.5” IN CEILING
TIC651 70/100 Volt In Ceiling 6.5” 2 Way
• In Ceiling 2 Way
• Woofer: 6.5” Fluted Injected Poly
• 1” Aluminum Dome Tweeter
• Butyl Rubber Surround
• Sonic Vortex® Ported Transmission Line
• Magnetic Bezelless Grille; White - Paintable
• Low Impedance: 8Ω
• 25V 0.2, 0.4, 0.7, 1.3, 2.5
• 70V 1.3, 2.5, 5, 10, 20
• 100V 20, 10, 5, 2.5
• 100V 2.5, 5, 10, 20
• Installed Frequency Response: 48Hz - 24kHz
• Sensitivity: 89db
• Power Handling: In 8Ω Mode 5-120W
• Connector Type: Four-position Plug-in Screw Terminal
• Speaker Weight: 7.10lbs (3.22kg)
• Cutout: 8.4” (214mm)
• Diameter 9.4” (239mm)
• Depth 6.8” (172mm)
• EZBracket Size: F
8” IN CEILING
TIC801 70/100 Volt In Ceiling 8” 2 Way
• In Ceiling 2 Way
• Woofer: 8” Fluted Injected Poly
• 1” Aluminum Dome Tweeter
• Butyl Rubber Surround
• Sonic Vortex® Ported Transmission Line Enclosure
• Magnetic Bezelless Grille; White - Paintable
• Low Impedance: 8Ω
• 25V 0.3, 0.5, 0.9, 1.8, 3.5
• 70V 1.9, 3.8, 7.5, 15, 30
• 100V 3.8, 7.5, 15, 30
• Installed Frequency Response: 35Hz - 24kHz
• Sensitivity: 92db
• Connector Type: Four-position Plug-in Screw Terminal
• Power Handling: In 8Ω Mode 5-120W
• Speaker Weight: 8.38 lbs (3.8kg)
• Cutout: 10.3” (261.5mm)
• Diameter 11.3” (284mm)
• Depth 8.6” (219.5mm)
• EZBracket Size: B

14
Specifications
4” SHALLOW DEPTH IN CEILING/IN WALL
TICW401 70/100 VOLT In Ceiling/In Wall 4” 2 Way
• In Wall or In Ceiling 2 Way
• Woofer : 4” Fluted Injected Poly
• ¾” Aluminum Dome Tweeter
• Butyl Rubber Surround
• Sonic Vortex® Ported Transmission Line Enclosure
• Magnetic Bezelless Grille; White - Paintable
• Low Impedance: 8Ω
• 25V 0.2, 0.3, 0.5, 0.9, 1.8
• 70V 1, 1.9, 3.8, 7.5, 15
• 100V Taps: 15, 7.5, 3.8, 1.9 Watts
• 100V 1.9, 3.8, 7.5, 15
• Installed Frequency Response: 68Hz - 24kHz
• Sensitivity: 89dB
• Connector Type: Four-position Plug-in Screw Terminal
• Power Handling: In 8Ω Mode 5-80W
• Speaker Weight: 2.59lbs (1.175kg)
• Cutout: ” 6.4” (162mm)
• Diameter ” 7.4” (186mm)
• Depth 3.82” (97mm)
• EZBracket Size: J
TU401 70/100 VOLT In Ceiling/In Wall 4” 2-Way Pancake
• In Wall or In Ceiling 2 Way
• Woofer: 4” Fluted Injected Poly
• ¾” Aluminum Dome Tweeter
• Butyl Rubber Surround
• Sonic Vortex® Ported Transmission Line
• Magnetic Bezelless Grille; White - Paintable
• Low Impedance: 8Ω
• 25V 0.2, 0.3, 0.5, 0.9, 1.8
• 70V 1, 1.9, 3.8, 7.5, 15
• 100V Taps: 15, 7.5, 3.8, 1.9 Watts
• 100V 1.9, 3.8, 7.5, 15
• Installed Frequency Response: 62Hz - 24kHz
• Sensitivity: 88dB
• Connector Type: Four-position Plug-in Screw Terminal
• Power Handling: In 8Ω Mode 5-80W
• Speaker Weight: 2.93lbs (1.33kg)
• Cutout: ” 8.4” (162mm)
• Diameter ” 9.5” (241.4mm)
• Depth 2.76” (70.2mm)
• EZBracket Size: F

15
Limited Lifetime Warranty
For Beale Street Audio Branded In-Wall and In-Ceiling Speakers and
Subwoofers Purchased after May 1, 2017
Limited Warranty
Vanco warrants to you, the original consumer purchaser of speakers, that under proper
use and conditions, and subject to the other conditions provided below, your speakers
will be free from defective materials and workmanship for the life of the speakers. This
warranty only applies to passive speakers. Active products, such as amplifiers, electronics,
and powered subwoofers are not covered under the Lifetime Warranty. Please review the
individual manual provided with each specific product for the warranty information.
What Vanco Will Do
If a speaker proves defective in either material or workmanship, Vanco, at its option,
will either (a) repair and return it to you, or (b) replace and ship you a new speaker of the
same model, unless your model is no longer available, in which case Vanco may replace
your speaker with a current model of comparable value. In either case, Vanco will pay the
shipping charge of sending you (US only) a replacement speaker or your repaired speaker.
If a current model is substituted for your speaker, a modification to the mounting surface
may be required. Vanco is not responsible or liable to make, account for or pay the cost of
any such modification.
How To Make A Warranty Claim
The first step in making a claim under this limited warranty is to contact the Vanco
authorized distributor/dealer where you purchased the speaker, or if you are unable to
contact the distributor/dealer, you can contact Vanco directly, for instructions on what
action to take. If it is necessary to return the speaker, it must be shipped in appropriate
packaging to the destination given to you, prepaid with signature required for delivery,
and be accompanied by (1) a document providing your name, address, phone number and
email address, and a statement of why you believe the speaker is defective, and (2) a copy
of your original receipt or bill of sale that identifies you as the original purchaser of the
speaker and the authorized distributor/dealer you purchased it from (“Proof of Purchase”).
You have the risk of loss or damage in transit to the destination, and therefore you are
responsible for insuring the shipment for the full value of the speaker. Freight collect
shipments will be refused. If Vanco determines this limited warranty does not cover your
claim, your speaker will be returned to you freight collect.
Exclusions and Limitations
This limited warranty does not cover:
> Speaker failure caused by anything other than a defect in material and workmanship.
> Consequential damage to other components, equipment or premises regardless of the
reason.
> The cost of removing and reinstalling your speaker.
> The cost of returning your speaker to Vanco.
> Any claims if you are unable to provide Proof of Purchase from a Vanco authorized
distributor/dealer.
Warranty continued next page

BSA70VIG070517 Rev 2
Limited Lifetime Warranty (cont)
For Beale Street Audio Branded In-Wall and In-Ceiling Speakers and
Subwoofers Purchased after May 1, 2017
A NEW BRAND FROM
Vanco International, LLC
506 Kingsland Drive
Batavia, IL 60510
Phone: [phone] Fax: [phone]
www.getbeale.com
©2017
This Limited Warranty Is Null And Void If Your Speaker:
> Was used in an application or environment other than that for which it was intended
> Misused, abused, improperly installed or removed
> Damaged by any accident, disaster or other cause not related to defects in materials
and workmanship.
> You sell or otherwise transfer your speaker to any other person.
> Was modified or repaired by anyone other than Vanco, or its serial number is altered,
defaced or removed.
REPAIR OR REPLACEMENT OF YOUR SPEAKER UNDER THIS WARRANTY IS YOUR
EXCLUSIVE REMEDY. IN NO EVENT WILL VANCO BE LIABLE FOR ANY AMOUNT GREATER
THAN THE ACTUAL PURCHASE PRICE PAID BY YOU FOR THE SPEAKER. VANCO SHALL
NOT BE LIABLE FOR ANY FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR INDIRECT
DAMAGES HOWSOEVER CAUSED. THIS LIMITED WARRANTY REPRESENTS THE ENTIRE
WARRANTY AGREEMENT BETWEEN YOU AND VANCO REGARDING YOUR SPEAKERS
AND IS GIVEN IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU
MAY ALSO HAVE OTHER RIGHTS THAT VARY, FROM STATE TO STATE. SOME STATES LIMIT
WHAT WARRANTIES MAY BE EXCLUDED AS WELL AS HOW LONG AN IMPLIED WARRANTY
LASTS, SO THESE LIMITATIONS MAY NOT APPLY TO YOU.
The Vanco logo, Sonic Vortex logo, and Beale Street Audio Inc. logo are registered trademarks of
Vanco International, LLC.
Vanco, Sonic Vortex, Beale Street Audio, Get Reale. Get Beale., the Vortex logo, and the Beale Street
Audio logo are trademarks of Vanco International, LLC.