Beale Street Audio IC6-BSC User manual

Beale Street Audio
IC6-BSC, IC8-BSC In-Ceiling Speakers
IC6DT-BSC Dual Tweeter Speaker
Installation Guide

2
Introduction
Speaker Wire
Congratulations and thank you for purchasing Beale Basics Series speakers
from Beale Street Audio!
Beale Basics In-Ceiling speakers install with ease using the ‘dog’ mounting
system and magnetic grilles for fast, clean installations.
Please follow the instructions in this manual to assure proper installation
and to achieve the full performance and satisfaction you would expect from
Beale Street Audio.
For the IC6-BSC and IC8-BSC, pull one run of 16-2 stranded speaker wire
from the amplifier location to each speaker location.
For the IC6DT-BSC, pull one run of 16-4 or 2 runs of 16-2 speaker wire
from the amplifier location to each speaker.
If in pre-wire, while the walls are open and it’s easy, pull extra wire to any
location that may be desirable to add speakers later. Leave extra length
of wire on each end to allow making connections and installing/removing
speakers.

3
New Construction
Beale Street Audio speaker installation can be simplified by using Beale
Street Audio new pre-construction brackets (sold separately; visit www.
getbeale.com for additional information).
TB65 and PRECB65: Use for the IC6-BSC and IC6DT-BSC
TB80 and PRECB80: Use for the IC8-BSC
These are installed prior to drywall installation and allows for precise
speaker placement and simplifies the final installation of the speaker.
Existing Construction
Speaker wire must be run from the equipment or volume control location to
each potential speaker location.
• Choose a location for each speaker that is free of obstructions created
by joists, HVAC ductwork, electrical wire runs, plumbing or anything else
that might not allow for the depth of the speaker or create interference
or noise

4
Installation
SPEAKER TROUBLESHOOTING
PROBLEM SOLUTION
NO SOUND Verify that there is audio from the
source selected. Select another
source if necessary.
Ensure that the amplifier is turned
on and connected properly.
Check any connections at other
devices, such as a volume control.
Temporarily bypass the control if
needed.
Check wire connections at each
speaker not producing sound for
good contact to bare wire, not wire
insulation.

5
Specifications
IC6-BSC 6.5” In-Ceiling 2 Way
• Woofer: 6.5” Kevlar Type Woven Cone
• Tweeter: 0.75” Titanium Dome
• RMS Power: 60W
• Nominal Impedance: 8Ω
• Sensitivity: 90dB
• Installed Frequency Response: 60Hz- 20kHz
• Product Dimension: 227x87mm (9” x 3.4”)
• Cutout Size: 210mm (8.3”)
IC8-BSC 8” In-Ceiling 2 Way
• Woofer: 8” Kevlar Type Woven Cone
• Tweeter: 0.75” Titanium Dome
• RMS Power: 80W
• Nominal Impedance: 8Ω
• Sensitivity: 90dB
• Installed Frequency Response: 50Hz- 20kHz
• Product Dimension: 227x105mm (10.9” x 4.1”)
• Cutout Size: 258mm (10.2”)
IC6DT-BSC 6.5” Dual Tweeter Speaker
• Woofer: 6.5” Kevlar Type Woven Cone
• Tweeter: Dual 0.75” Titanium Dome
• RMS Power: 60W
• Nominal Impedance: 8Ω
• Sensitivity: 90dB
• Installed Frequency Response: 55Hz- 20kHz
• Product Dimension: 227x87mm (9” x 3.4”)
• Cutout Size: 210mm (8.3”)