Behringer COMPOSER PRO MDX2200 User manual

COMPOSER® PRO MDX2200
www.behringer.com
ENGLISH
Users Manual
Version 1.3 June 2001

2
COMPOSER PRO MDX2200
This s mbol, wherever it appears, alerts
ou to important operating and mainte-
nance instructions in the accompan ing
literature. Read the manual.
SAFETY INSTRUCTIONS
CAUTION: To reduce the risk of electric shock, do not remove
the cover (or back). No user serviceable parts inside;
refer servicing to qualified personnel.
WARNING: To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
DETAILED SAFETY INSTRUCTIONS:
All the safet and operation instructions should be read before the appliance is operated.
Retain Instructions:
The safet and operating instructions should be retained for future reference.
Heed Warnings:
All warnings on the appliance and in the operating instructions should be adhered to.
Follo instructions:
All operation and user instructions should be followed.
Water and Moisture:
The appliance should not be used near water (e.g. near a bathtub, washbowl, kitchen sink, laundr tub, in a wet
basement, or near a swimming pool etc.).
Ventilation:
The appliance should be situated so that its location or position does not interfere with its proper ventilation.
For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that ma block the
ventilation openings, or placed in a built-in installation, such as a bookcase or cabinet that ma impede the
flow of air through the ventilation openings.
Heat:
The appliance should be situated awa from heat sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.
Po er Source:
The appliance should be connected to a power suppl onl of the t pe described in the operating instructions
or as marked on the appliance.
Grounding or Polarization:
Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.
Po er-Cord Protection:
Power suppl cords should be routed so that the are not likel to be walked on or pinched b items placed
upon or against them, pa ing particular attention to cords and plugs, convenience receptacles and the point
where the exit from the appliance.
Cleaning:
The appliance should be cleaned onl as recommended b the manufacturer.
Non-use Periods:
The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.
Debris and Liquid Entry:
Care should be taken that debris and/or liquids do not enter the enclosure through openings.
Damage Requiring Service:
The appliance should be serviced b qualified service personnel when:
- The power suppl cord or the plug has been damaged; or
- Debris or liquid has entered the appliance; or
- The appliance has been exposed to rain; or
- The appliance does not appear to operate normall or exhibits a marked change in performance; or
- The appliance has been dropped, or the enclosure damaged.
Servicing:
The user should not attempt to service the appliance be ond that which is described in the operating instruc-
tions. All other servicing should be referred to qualified service personnel.
This s mbol, wherever it appears,
alerts ou to the presence of
uninsulated dangerous voltage inside
the enclosurevoltage that ma be
sufficient to constitute a risk of shock.

3
COMPOSER PRO MDX2200
FOREWORD
Dear Customer,
Welcome to the team of COMPOSER PRO users and thank ou ver much for expressing our confidence in
BEHRINGER products b purchasing this unit.
It is one of m most pleasant tasks to write this letter to ou, because it is the culmination of man months of
hard work delivered b our engineering team to reach a ver ambitious goal: making an outstanding device
better still. The COMPOSER has for quite a long time been a standard tool used b numerous studios and
PA rental companies. The task to improve one of our best-selling products certainl meant a great deal of
responsibilit , which we assumed b focusing on ou, the discerning user and musician. It also meant a lot of
work and night shifts to accomplish this goal. But it was fun, too. Developing a product usuall brings a lot of
people together, and what a great feeling it is when ever bod who participated in such a project can be proud
of what weve achieved.
It is our philosoph to share our jo with ou, because ou are the most important member of the BEHRINGER
famil . With our highl competent suggestions for new products ouve greatl contributed to shaping our
compan and making it successful. In return, we guarantee ou uncompromising qualit (manufactured under
ISO9000 certified management s stem) as well as excellent technical and audio properties at an extremel
favorable price. All of this will enable ou to full unfold our creativit without being hampered b budget
constraints.
We are often asked how we can make it to produce such high-grade devices at such unbelievabl low prices.
The answer is quite simple: its ou, our customers! Man satisfied customers means large sales volumes
enabling us to get better conditions of purchase for components, etc. Isnt it onl fair to pass this benefit back
to ou? Because we know that our success is our success, too!
I would like to thank all people whose help on Project COMPOSER PRO has made it all possible. Ever bod
has made ver personal contributions, starting from the designers of the unit via the man staff members in m
compan to ou, the user of BEHRINGER products.
M friends, its been worth the trouble!
Thank ou ver much,
Uli Behringer

4
COMPOSER PRO MDX2200
MDX2200
COMPOSER® PRO
Interactive 2-channel expander/gate/compressor/limiter of the reference class
sIKA (Interactive Knee Adaptation) compressor concept combines the advantages of hard knee and soft
knee characteristics
sAttack and release times controllable automaticall or manuall
sSwitchable high-pass filter in control signal path avoids low-frequenc signals from dominating compressor
action
sCompression characteristics switchable between IKA and hard knee characteristics
sIRC circuit in expander/gate allows for inaudible elimination of disturbing noise signals
sIGC (Interactive Gain Control) peak limiter combines clipper with program limiter circuits
sExtremel low-noise operational amplifiers and high-grade VCAs
sHigh-qualit detent potentiometers and backlit switches
sStereo couple function selectable with real totaling of RMS output
sAccurate 12-digit LED meters for input level, output level and gain reduction
sTraffic-light function for eas threshold setting
sSwitchable side chain input with side chain monitor function
sOperating level switchable from +4 dBu to -10 dBV
sServo-balanced inputs and outputs featuring 6.3 mm TRS and XLR connectors
sHigh-grade output transformer BEHRINGER OT-1 can be retrofitted
sRela -controlled hard-b pass switch with auto-b pass function (failsafe rela )
sManufactured under ISO9000 certified management s stem

5
COMPOSER PRO MDX2200
TABLE OF CONTENTS
1. INTRODUCTION..................................................................................................................... 7
1.1 Before ou begin ............................................................................................................................. 8
1.2 Design concept ............................................................................................................................... 8
1.2.1 High qualit components and design ..................................................................................... 8
1.2.2 Failsafe rela s ...................................................................................................................... 8
1.2.3 Balanced inputs and outputs ................................................................................................. 8
1.2.4 Transformer balanced outputs (optional) ................................................................................ 9
2. CONTROL ELEMENTS ......................................................................................................... 9
2.1 Expander/gate section .................................................................................................................... 9
2.2 Compressor section ...................................................................................................................... 10
2.3 Peak limiter section ....................................................................................................................... 11
2.4 Rear panel control elements of the COMPOSER PRO .................................................................. 12
3. TECHNICAL BACKGROUND .............................................................................................. 12
3.1 Noise as a ph sical phenomenon .................................................................................................. 12
3.2 What are audio d namics? ........................................................................................................... 13
3.3 Compressors/limiters .................................................................................................................... 14
3.4 Expanders/noise-gates ................................................................................................................. 14
4. APPLICATIONS ..................................................................................................................... 15
4.1 Compression/levelling/limiting/clipping ........................................................................................... 15
4.2 Expander/gate section .................................................................................................................. 16
4.2.1 Controlling leakage in the studio ......................................................................................... 17
4.2.2 Initial settings for the expander/gate section ....................................................................... 17
4.2.3 Reducing leakage in stage mics ......................................................................................... 18
4.2.4 Reducing feedback in stage mics ....................................................................................... 18
4.2.5 Noise reduction on effects paths ......................................................................................... 18
4.2.6 Creative use of the expander/gate section ........................................................................... 18
4.3 Compressor section ...................................................................................................................... 18
4.3.1 Initial settings for the compressor section ........................................................................... 19
4.3.2 The COMPOSER PRO as a sound effects unit ................................................................... 20
4.3.3 The muffling effect of a compressor ................................................................................... 20
4.4 Peak limiter section ...................................................................................................................... 20
4.4.1 Initial settings for the peak limiter section ........................................................................... 21
5. SPECIAL APPLICATIONS ..................................................................................................... 21
5.1 Using the COMPOSER PRO for recording and cassette duplication ............................................. 21
5.1.1 The COMPOSER PRO in digital recording and sampling .................................................... 22
5.1.2 The COMPOSER PRO in mastering ................................................................................... 22
5.2 The COMPOSER PRO as a protective device ............................................................................... 22
5.2.1 Protection of a s stem with a passive crossover ................................................................. 23
5.2.2 Protection of a s stem with an active crossover .................................................................. 23
5.2.3 Improving the sound of a processor s stem ........................................................................ 23
5.3 The COMPOSER PRO in broadcast ............................................................................................. 23

6
COMPOSER PRO MDX2200
6. EXTERNAL SIDE CHAIN APPLICATIONS ........................................................................... 24
6.1 The side chain function ................................................................................................................. 24
6.2 Using an equalizer in the side chain path ..................................................................................... 24
6.2.1 The COMPOSER PRO as a de-esser ............................................................................... 24
6.2.2 Frequenc -selective filtering of unwanted signals ................................................................ 25
6.2.3 Suppressing instruments during recording ........................................................................... 25
6.2.4 Emphasizing musical instruments during recording ............................................................. 25
6.3 Anticipated compression ............................................................................................................... 25
6.4 Voice-over compression (ducking) ............................................................................................. 26
6.5 Triggering additional sounds from a rh thm track........................................................................... 26
7. INSTALLATION ..................................................................................................................... 26
7.1 Rack mounting .............................................................................................................................. 26
7.2 Audio connections ........................................................................................................................ 26
7.3 Selecting the operating level .......................................................................................................... 27
8. SPECIFICATIONS .................................................................................................................. 28
9. ARRANTY ........................................................................................................................... 30

7
COMPOSER PRO MDX2200
1. INTRODUCTION
In purchasing the new COMPOSER PRO MDX 2200, ou have acquired an extremel efficient and universal
d namics processor, which combines the most commonl used d namic functions within a compact stereo
unit: ever channel has its own independent compressor/limiter, an expander/gate and a peak limiter. The
precision and flexibilit of the functions are the main outstanding features of this high end unit.
Despite the extremel complex internal circuitr , the unit has a control surface which is clearl laid out and
eas to understand. The internal design of the unit, together with its external side-chain path, gives the user
unsurpassed creative flexibilit when processing sound.
Advanced BEHRINGER technology
Compared to its predecessors, the COMPOSER PRO offers several advanced features such as the extended
LED meters for ease of operation when setting the threshold, the adjustable expansion ratio in the expander/
gate section and the side chain filter. Additionall , we have succeeded in refining the audio properties as well
as the circuit topolog .
For the first time, the COMPOSER PRO MDX 2200 uses SMD technolog (Surface Mounted Device). These
sub-miniature components known from aerospace technolog allow for an extreme packing densit , plus
improve the units reliabilit .
IKA (Interactive Knee Adaption) compressor
Our proven IKA (Interactive Knee Adaptation) circuit successfull combines the concept of a hard knee
compressor with the characteristics of a soft knee approach. This program-dependent regulation scheme
forms the prerequisite both for inaudible and musical program compression and for creative and highl
effective d namics processing.
With its IKA circuit the COMPOSER PRO is capable of delivering outstanding musical results both in studio
and live PA applications.
Additionall , the COMPOSER PROs side-chain filter allows for limiting the influence low-frequenc signal
portions usuall have on the control logic, so that the compression ratio is mainl determined b those
frequencies that are essential to the loudness perceived b the listenerthe midrange frequencies.
IRC (Interactive Ratio Control) expander
A basic problem in the use of a compressor is the fact that the noise floor is highl amplified during quiet
sections or when there are music pauses. This effect is exaggerated when the compression ratio is inappropri-
ate. In order to eliminate this problem, one would normall use an additional expander or gate. The noise is
then simpl faded out in the quiet sections. However, simple expanders, even when the are used correctl ,
drasticall cut signals below the preset threshold. This effect becomes more noticeable during the transition
from signal to noise floor. This can mean, that the start or end of words can be cut on a vocal track.
A newl developed IRC (Interactive Ratio Control) expander has been integrated into the COMPOSER PRO the
ratio of which, is automaticall adjusted, depending on the program material. The result is an expander which
is less critical of adjustment and which is more tolerant in the presence of those signals which appear slightl
above the noise floor. Because of its new IRC circuit design, the BEHRINGER COMPOSER PRO expander/
gate section can be used as an independent unit to eradicate noise offering almost limitless possibilities within
this application.
IGC (Interactive Gain Control) peak limiter
A further remarkable feature of the BEHRINGER COMPOSER PRO is the IGC (Interactive Gain Control)
limiter, an intelligent combination of a clipper and a program limiter. Above an adjustable threshold the peak
limiter begins to function and restricts signal peaks radicall (clipper). If however, the threshold of the limiter
was surpassed for more than a few milliseconds, the IGC circuit automaticall kicks in and reduces the level
of the overall output signal so that no audible distortion occurs (program limiter). After the level falls below the
threshold, the signal returns to the original value after a period of about 1 second. This IGC circuit proves to be
extremel valuable as much for live work (loudspeaker protection) as for digital situations, where an extreme
signal peaks would exceed the maximum headroom and therefore would cause severe problems. The following
instructions should initiall familiarize ou with the special terms used, so that ou can get to know all the
functions of the unit. After ou have read the instructions carefull , please put them awa safel , so that ou
can refer to them again if necessar .
1. INTRODUCTION

8
COMPOSER PRO MDX2200
1.1 Before you begin
The BEHRINGER COMPOSER PRO MDX2200 was carefull packed in the factor , in order to ensure safe
transport. Nevertheless, should the box show signs of damage please check the equipment itself immediatel
for an signs of external damage.
+If the unit is damaged, please do not return it to us, but notify your dealer and the shipping
company immediately, other ise claims for damage or replacement may not be granted.
Shipping claims must be made by the consignee.
Be sure that there is enough space around the unit for cooling and please do not place the COMPOSER PRO
on high-temperature devices such as power amplifiers, etc. to avoid overheating.
+Before connecting the COMPOSER PRO to the mains, please carefully check that your
equipment is set to the correct supply voltage!
The fuse holder on the female mains connector has 3 triangular markings. Two of these triangles are opposite
each other. The MDX2200 is set to the operating voltage shown next to these markings. It can be set to another
voltage b turning the fuse holder through 180°. CAUTION: this does not apply to export models, hich
ere designed e.g. only for a mains voltage of 115 V!
Connection to the mains is made b means of a mains cable with an IEC receptacle which complies with the
appropriate safet regulations.
+Please note that all units must be grounded properly. For your o n safety, you should never
remove any ground connectors from electrical devices or po er cords or render them in-
operative.
1.2 Design concept
1.2.1 High quality components and design
The philosoph behind BEHRINGER products guarantees a no-compromise circuit design and emplo s the
best choice of components. The operational amplifiers NJM4580 which are used in the COMPOSER PRO, are
exceptional. The boast extreme linearit and ver low distortion characteristics. The most important aspect of
the COMPOSER PRO design is a radical VCA implementation which results in outstanding technical
specification and excellent performance. To complement this design the choice of components includes high
tolerance resistors and capacitors, detent potentiometers, gold plated rela contacts and several other
stringentl selected elements.
For the first time, the COMPOSER PRO MDX 2200 uses SMD technolog (Surface Mounted Device). These
sub-miniature components known from aerospace technolog allow for an extreme packing densit , plus the
units reliabilit could be improved. Additionall , the unit is manufactured in compliance with a ISO9000
certified management s stem.
1.2.2 Failsafe relays
Failsafe rela s have been incorporated into the design of the BEHRINGER COMPOSER PRO, which
automaticall and silentl b pass the unit in the event of power suppl disconnection or failure. These rela s
are also active at switch-on to isolate the COMPOSER PRO until the power rails have settled, thus preventing
the possibilit of a potentiall damaging switch-on thump.
1.2.3 Balanced inputs and outputs
As standard, the BEHRINGER COMPOSER PRO is installed with electronicall servo-balanced inputs and
outputs. The new circuit design features automatic hum and noise reduction for balanced signals and thus
allows for trouble-free operation, even at high operating levels. Externall induced mains hum etc. will be
effectivel suppressed. The automatic servo-function recognizes the presence of unbalanced connectors and
adjusts the nominal level internall to avoid level differences between the input and output signals (correction
6dB).
1. INTRODUCTION

9
COMPOSER PRO MDX2200
1.2.4 Transformer balanced outputs (optional)
In contrast to electronic balancing, the use of transformer-balanced outputs offers the advantage of galvanic
separation between units. Electrical potential differences and ground loops in audio installations do not there-
fore impair the performance of the units. The transformer-balanced outputs, commonl used in radio and TV
engineering, can also be fitted retrospectivel upon request. The BEHRINGER transformer OT-1 is designed to
the highest exacting standards and is available as an accessor .
2. CONTROL ELEMENTS
1
Fig. 2.1: COMPOSER PRO front panel
The BEHRINGER COMPOSER PRO has two identical channels. Each channel is equipped with eight backlit
push-buttons, eight rotar controls and 30 LEDs. The COUPLE switch is for stereo operation:
1
B engaging the COUPLE switch the COMPOSER PRO is converted to stereo mode, where the controls of
the left channel take over the control of both audio channels. The control signal for the control
characteristic consists of either the sum of the left and right audio signal or the sum of the external audio
signals, which are being fed into both SC RETURN connectors. B pressing the COUPLE switch, ou
override all the controls and switches of channel 2 with the exception of the IN/OUT, SC EXT, SC MON,
SCFILTER and I/O METER switches. As a result, the controls of channel 1 take over the functions of
channel 2.
+Should you ish to use the SC EXT function in stereo mode, then be sure that both SC RETURN
connectors are connected to the external control signal, and that the SC EXT s itches on both
channels are engaged.
2.1 Expander/gate section
Fig. 2.2: Control elements of expander/gate se tion
2
Use the THRESHOLD control to determine the threshold point below which expansion occurs. The
range of this control is from OFF to +15 dB.
2. CONTROL ELEMENTS

10
COMPOSER PRO MDX2200
3
The RATIO control is used to adjust the expansion ratio when the signal drops below the threshold
value. This control determines whether the unit works as an expander (low ratio level) or as a gate (1:8).
The expansion ratio can be set from 1:1 to 1:8.
4
When a signal below the threshold value is applied, the - LED lights up, while the +-LED lights up
when expansion occurs.
5
To optimall adapt the expander/gate to the program material, the RELEASE switch allows for selecting
a SLOW or FAST release time. When ou engage this switch, the expander responds with a slow
release. As a general rule, percussive material with little or no ambience is processed using the FAST
release mode, whereas signals with long deca or with heav ambience require the SLOW release
mode.
2.2 Compressor section
Fig. 2.3: Control elements of the ompressor se tion
6
The THRESHOLD control sets the threshold point for the compressor section. It has a range of -40 to
+20 dB. The soft knee characteristic is applied to the signal exceeding the threshold point b a
maximum of 10 dB. Above 10 dB, the signal would experience hard knee compression. The
THRESHOLD-LEDs show the actual state of the input signal relative to the THRESHOLD setting. The
IKA-soft knee range is indicated b the middle ellow LED.
7
The RATIO control determines the ratio between the input and output level for all signals exceeding the
threshold point b more than 10 dB. The control range can be adjusted from 1:1 to oo:1.
8
The ATTACK control determines the rate b which the compressor responds to the signal which ex-
ceeds the threshold. This control can be adjusted from 1 to 150 milliseconds.
9
The RELEASE control determines the rate that the compressor returns to unit gain after falling below
the threshold level. This control can be adjusted from 0.05 to 5 seconds.
10
B activating the AUTO switch, the ATTACK and RELEASE controls are disabled and the attack and
release rates are automaticall derived from the programme material. This function allows for unobtru-
sive musical compression of signals or mixes with widel var ing d namics. Onl if set to MANUAL
will the settings of the attack and release controls function.
11
The OUTPUT control allows for the increase or decrease of the output signal b a maximum of 20 dB.
Thus, a level loss due to the compression or limiting process can be compensated for.
+Please note hen using the THRESHOLD control of the peak limiter section, that the OUTPUT
control of the compressor section precedes the peak limiter section. If the OUTPUT control is
set too high, this can result in continuous peak limiting (see item 19 THRESHOLD control).
12
When activated, the SC EXT switch severs the connection between the audio input and the side chain
path, whilst at the same time allowing an external signal to be sourced at the SC RETURN jack on the
rear panel.
2. CONTROL ELEMENTS

11
COMPOSER PRO MDX2200
13
Using the SC MON switch will enable ou to connect the side chain control signal to the audio output,
whilst at the same time muting the audio input. This function provides ou with the abilit to monitor the
side chain signal that is returned via inserted equalizers or other external processors. The SC MONITOR
function will assist ou with tuning equalizer parameters for example.
+Please note hen the SC MON s itch is engaged, the audio processing facility of the respec-
tive channel is disabled. When this function is active, a visual indication ill be provided by
the s itches LED, hich ill blink.
14
The IN/OUT switch activates the rela and hence the corresponding channel. This switch acts as a so-
called hard-b pass rela , which means that when the switch is OUT or when the unit is disconnected
from the mains, the input jack is directl linked to the output jack. Normall , this switch is used to
perform a direct A/B comparison between the unprocessed and the compressed or limited signals.
15
Press the INTERACTIVE switch to change from hard knee to IKA characteristics. IKA provides a ver
subtle and musical compression of the program material and should therefore be used whenever
compression should be more or less inaudible.
16
The SC FILTER switch activates a high-pass filter in the side-chain path and thus limits the influence of
low frequencies on the COMPOSER PROs control processes.
17
The 12-digit GAIN REDUCTION meter indicates how effectivel the gain is reduced b the compressor,
within a range from 1 to 30 dB.
18
The 12-digit INPUT/OUTPUT LEVEL meter informs oudepending on the setting of the I/O METER
switchabout the current input or output level, within a range from -30 to +18 dB. When the switch is
set to IN (engaged), the meter reads the input level, when it is OUT (not engaged), the output level is
displa ed. The meter is referenced to the operating level (-10 dBV or +4 dBu) adjusted with the
OPERATING LEVEL switch.
2.3 Peak limiter section
Fig. 2.4: Control elements of the peak limiter se tion
19
The peak limiter limits the signal to a level adjusted with the THRESHOLD control. Owing to its
extremel fast response (zero attack), the limiter is capable of limiting signal peaks without audible
distortion. Whenever the signal is limited for more than 20 ms, the overall level is reduced for about
1 second to avoid heav and thus audible signal distortion.
+When you use the peak limiter as a protective device against signal peaks, the THRESHOLD
control should be set in combination ith the OUTPUT control in the compressor section so
that the peak limiter responds rarely or not at all. Thus, only real signal peaks ill activate the
limiter circuit. Ho ever, to produce creative sound effects, the peak limiter can be
deliberately set to lo er levels.
20
The LIM LED lights up as soon as the limiter function is activated.
2. CONTROL ELEMENTS

12
COMPOSER PRO MDX2200
2. Rear panel control elements of the COMPOSER PRO
Fig. 2.5: Control elements of the rear panel
21
SERIAL NUMBER. Please take the time to complete and return the warrant card within 14 da s of the
date of purchase, otherwise ou will lose the right to the extended warrant . Or just use our online-
registration (www.behringer.com).
22
FUSE HOLDER/VOLTAGE SELECTOR. Before connecting the equipment to the mains suppl , please
check that the voltage displa conforms with our mains voltage suppl . When replacing the fuse, make
sure ou use another one of the same t pe. With man units the fuse holder can be set in one of two
positions, in order to switch between 230 V and 115 V. Please note: if ou wish to operate a unit outside
Europe, then a stronger fuse must be used.
23
MAINS CONNECTION. Use the enclosed power cord to connect the unit to the mains. Please also note
the instructions given in the chapter 7. INSTALLATION.
24
AUDIO IN. These are the audio inputs of our COMPOSER PRO, available both as balanced 6.3 mm
jack and XLR connectors.
25
AUDIO OUT. These are the audio outputs of our COMPOSER PRO. Matching phone jack and XLR
connectors are wired in parallel. These outputs can be transformer-balanced b retrofitting the optional
output transformer OT-1.
26
With the OPERATING LEVEL switch ou can adapt the COMPOSER PRO to various operating levels,
i.e. ou can select both the -10 dBV home recording level and the professional studio level of +4 dBu.
The level meters are referenced automaticall to the selected level, i.e. an optimum operating range of
the meters will alwa s be ensured.
27
SC SEND. This is the unbalanced side-chain output which allows for routing the audio signal to external
processing devices.
28
SC RETURN. This is the unbalanced side-chain input used to return an external or processed control
signal.
3. TECHNICAL BACKGROUND
B emplo ing current modern analog technolog it is possible to manufacture audio equipment with a d namic
range of up to 125 dB. In contrast to analog techniques, the d namic range of digital equipment is approxi-
matel 25 dB less. With conventional record and tape recorder technolog , as well as broadcasting, this value
is further reduced. Generall , d namic restrictions are due to nois storage in transmission media and also the
maximum headroom of these s stems.
3.1 Noise as a physical phenomenon
All electrical components produce a certain level of inherent noise. Current flowing through a conductor leads
to uncontrolled random electron movements. For statistical reasons, this produces frequencies within the
whole audio spectrum. If these currents are highl amplified, the result will be perceived as noise. Since all
frequencies are equall affected, we term this white noise. It is fairl obvious that electronics cannot function
without components. Even if special low-noise components are used, a certain degree of basic noise cannot
be avoided.
This effect is similar when repla ing a tape. The non-directional magnetic particles passing the repla head can
3. TECHNICAL BACKGROUND

13
COMPOSER PRO MDX2200
also cause uncontrolled currents and voltages. The resulting sound of the various frequencies is heard as
noise. Even the best possible tape biasing can onl  provide signal-to-noise ratios of about 70 dB, which is not
acceptable toda since the demands of listeners have increased. Due to the laws of ph sics, improving the
design of the magnetic carrier is impossible using conventional means.
3.2 What are audio dynamics?
A remarkable feature of the human ear is that it can detect the most wide ranging amplitude changes - from the
slightest whisper to the deafening roar of a jet-plane. If one tried to record or reproduce this wide spectrum of
sound with the help of amplifiers, cassette recorders, records or even digital recorders (CD, DAT etc.), one
would immediatel be restricted b the ph sical limitations of electronic and acoustic sound reproduction
technolog .
The usable d namic range of electro-acoustic equipment is limited as much at the low end as at the high end.
The thermal noise of the electrons in the components results in an audible basic noise floor and thus repre-
sents the bottom limit of the transmission range. The upper limit is determined b the levels of the internal
operating voltages; if the are exceeded, audible signal distortion is the result. Although in theor , the usable
d namic range sits between these two limits, it is considerabl smaller in practice, since a certain reserve
must be maintained to avoid distortion of the audio signal if sudden level peaks occur. Technicall speaking,
we refer to this reserve as headroom - usuall this is about 10 - 20 dB. A reduction of the operating level would
allow for greater headroom, i.e. the risk of signal distortion due to level peaks would be reduced. However, at
the same time, the basic noise floor of the program material would be increased considerabl .
Ear
Microphone Amplifier
Power Amplifier
Tape Recorder
Radio
Cassette
Recorder
P/dB
140
120
100
80
60
40
Fig. 3.1: The dynami range apabilities of various devi es
It is therefore useful to keep the operating level as high as possible without risking signal distortion in order to
achieve optimum transmission qualit .
It is possible to further improve the transmission qualit b constantl monitoring the program material with the
aid of a volume fader, which manuall levels the material. During low passages the gain is increased, during
loud passages the gain is reduced. Of course it is fairl obvious that this kind of manual control is rather
restrictive; it is difficult to detect signal peaks and it is almost impossible to level them out. Manual control is
simpl not fast enough to be satisfactor .
3. TECHNICAL BACKGROUND

14
COMPOSER PRO MDX2200
t
P/dB
+20
0
-20
-40
-60
-80
Clipping
Headroom
Operating level
Effective SNR
Noise floor
Fig. 3.2: The intera tive relationship between the operating level and the headroom
The need therefore arises for a fast acting automatic gain control s stem which will constantl monitor the
signals and which will alwa s adjust the gain to maximize the signal-to-noise ratio without incurring signal
distortion. This device is called a compressor or limiter. This s stem is a part of the COMPOSER PRO.
3.3 Compressors/limiters
B measuring the d namic range of musical instruments in live recording situations, ou will find that extreme
amplitudes occur which often lead to overload in subsequent signal processing equipment. Especiall in
broadcasting and record cutting techniques, these signal peaks can lead to heav distortion. To avoid this kind
of distortion or, for example, to avoid loudspeakers being damaged b overload, compressors or limiters are
used.
The principal function used in these devices is dependent on an automatic gain control as mentioned in the
previous section, which reduces the amplitude of loud passages and therefore restricts the original d namics
to a desired range. This application is particularl useful in microphone recording techniques, to compensate
for level changes which are caused b var ing microphone distances. Although compressors and limiters
perform similar tasks, one essential point makes them different: Limiters abruptl limit the signal above a
certain level, while compressors control the signal gentl  over a wider range. A limiter continuousl monitors
the signal and intervenes as soon as the level exceeds a user-adjustable threshold. An signal exceeding this
threshold will be immediatel returned to the adjusted level.
A compressor also monitors the program material continuousl and has a certain threshold level. With com-
pression, in contrast to the action of a limiter, signals are not reduced in level abruptl once the threshold has
been exceeded, but are returned to the threshold graduall . The signal is reduced in gain, relative to the
amount the signal exceeds this point.
Generall , threshold levels for compressors are set below the normal operating level to allow for the upper
d namics to be musicall compressed. For limiters, the threshold point is set above the normal operating level
in order to provide reliable signal limiting, to protect subsequent equipment from signal overload.
3. Expanders/noise-gates
Audio, in general, is onl as good as the source from which it was derived. The d namic range of signals will
often be restricted b noise. S nthesizers, effects devices, guitar pickups, amplifiers etc. generall produce a
high level of noise, hum or other ambient background hiss, which can disturb the qualit of the program
material.
Normall these noises are inaudible if the level of the desired signal lies significantl above the level of the
noise. This perception b the ear is based on the masking effect: noise will be masked and thus becomes
3. TECHNICAL BACKGROUND

15
COMPOSER PRO MDX2200
inaudible as soon as considerabl louder sound signals in the same frequenc band are added. Nevertheless,
the further the level that the desired signal decreases, the more the noise floor becomes a disturbing factor.
Expanders or noise-gates offer a solution for this problem: these devices attenuate signals when their ampli-
tudes drop, thereb fading out the background noise. Rel ing on this method, gain controlling amplifiers, like
expanders, can extend the d namic range of a signal and are therefore the opposite of a compressor.
In practice, it is shown that an expansion over the entire d namic range is not desired. With an expansion ratio
of 5:1 and a processed d namic range of 30 dB, an output d namic range of 150 dB will be the result,
exceeding all subsequent signal processors, as well as human hearing. Therefore, the amplitude control is
restricted to signals whose levels are below a certain threshold. Signals above this threshold pass through the
unit unchanged. Due to the continuous attenuation of the signals below this threshold, this kind of expansion
is termed downward expansion.
The noise-gate is the simplest form of an expander: in contrast to the expander, which continuousl attenuates
a signal below the threshold, the noise-gate cuts off the signal abruptl . In most applications this method is not
ver useful, since the on/off transition is too drastic. The onset of a simple gate function appears ver obvious
and unnatural. To achieve inaudible processing of the program material, it is necessar to be able to control the
signals envelope parameters. This is part of the man features of the COMPOSER PRO.
4. APPLICATIONS
In this section, several t pical applications of the BEHRINGER COMPOSER PRO are discussed. The follow-
ing basic settings can resolve most d namic problems. The are the ideal starting point. Please take the time
to stud the application examples carefull , in order to be able to make full use of the COMPOSER PROs
capabilities in the future.
Main Applications And Initial Settings
The main applications of the COMPOSER PRO can be divided into three categories:
1. The EXPANDER/GATE section is used to eliminate interference and to suppress background noise and
leakage on individual tracks in multitrack recording.
2. The COMPRESSOR section is used to compress the program material and to create special effects and
unusual sounds, which are used for recording and musical performance.
3. The subsequent PEAK LIMITER section is designed to protect loudspeakers, tape recorders, transmitters
etc. from being overloaded.
.1 Compression/levelling/limiting/clipping
Now that the functions of the individual sections have been clearl explained, we would like to acquaint ou
with more terms and relationships of the d namics process.
Compression
A compressor converts a large d namic level into a restricted range. The extent of the resulting d namic level
is dependent on the threshold, attack, release and ratio settings. As it is the desired effect of a compressor to
increase a low level signal, generall the threshold is set low. The inaudible compression mode requires fast
attack and release times and low ratios. The faster the chosen control times and the higher the compression
ratio, the greater the effect on the short term d namics. This fact is often used to achieve audible and creative
sound effects.
Levelling
The levelling mode is used to keep output level constant, i.e. to compensate for long term gain changes,
without affecting the short term d namics. Normall , the threshold is set quite low in order to be able to
increase low level signals. Levelling requires slow attack and release times, combined with a high ratio. Be-
cause of the ver slow response time, levelling has no effect on signal peaks or short term changes in average
level.
Limiting
The limiting function requires a fast attack time and a high ratio and release time setting, which is dependent
on the specific use and the desired sound effect. As it is usuall the task of a limiter to limit onl high signal
peaks, the threshold is usuall set at a high level. The d namics are reduced dependent on the ratio setting
and the degree b which the threshold point was exceeded. If the attack time is adjusted to control onl the
4. APPLICATIONS

16
COMPOSER PRO MDX2200
average level without affecting signal peaks above the threshold, this is referred to as the program limiter. For
this purpose the attack time will be set above 20 ms. If the attack time is further reduced in order to also control
signal peaks, this is defined as the peak limiter.
Clipping
In contrast to the two previousl mentioned limiters, the clipping mode features infinitel fast control times, an
infinite compression ratio and creates an unsurpassable barrier (brickwall) for all signals above a certain level.
To be able to control the signal peaks, the clipping function radicall cuts signals above the threshold, without
affecting the amplitude of the original signal. If used in normal applications, this function remains inaudible and
under certain circumstances it can even lead to an improved sound, because cutting the transients creates
artificial harmonics. If misused, clipping can cause ver obvious and distasteful distortion, which in an extreme
manner, will convert the signals waveform into a square wave signal. This effect is often produced in guitar
distortion devices (fuzz boxes).
.2 Expander/gate section
The main task of the expander/gate is to inaudibl  eliminate undesirable background noise from the usable
signal. As alread described in chapter 3.4, a downward expander automaticall reduces the overall level for all
signals below an adjustable threshold. The expander therefore operates in opposite wa to that of a compres-
sor/limiter. Expanders generall function with a flat ratio curve, so that the signal continuall fades. Noise-
gates however, can be seen as high ratio expanders. If the signal falls below the threshold, it is radicall
attenuated.
The BEHRINGER COMPOSER PRO is equipped with a newl developed IRC (Interactive Ratio Control) Ex-
pander, the ratio of which is automaticall adjusted dependent on the program material. The response charac-
teristics of conventional expanders tend to cut into the signal abruptl and the result of this is unacceptable
most of the time. Gain changes become audible.
The IRC Expander is therefore equipped with a soft, interactive non-linear ratio curve, which is best suited to
human hearing. Critical signals in the vicinit of the threshold level are processed with a minute expansion
ratio, whereas signals that reduce in level will be subjected to an increasingl higher ratio, which will result in
greater attenuation.
Threshold
Gain 0 dB
Input
Output
1:oo
Noise Gate,
Expander, 1:8
IRC-Curve
Fig. 4.1: IRC urve hara teristi of the Expander
The result is expansion, which is less critical to adjust and which is more tolerant of useable signals, whose
level is slightl above that of the noise floor. Expansion therefore occurs extremel soft with low ratio settings,
while the known negative effects of expansion are inaudible. The attack time of the IRC expander is set
automaticall and program-dependent, i.e. extremel short for quickl changing signals and slower for a more
balanced program material. Since the expander/gate adapts itself automaticall to the program material, ou
will note that the new IRC (Interactive Ratio Control) circuit produces considerabl better results than conven-
tional expanders.
4. APPLICATIONS

17
COMPOSER PRO MDX2200
4.2.1 Controlling leakage in the studio
Expander/gates are most commonl used to suppress undesirable leakage of sound from one track to another
during recording or pla back. The are usuall used when recording drum kits, where the mics are ver close
to each other. High volume levels of individual instruments often cause considerable leakage onto all the
adjacent mics and results in conflicting frequenc and phase coherence problems, as well as unspecified
sounds (comb filter effects). It is vitall important that ever instrument is recorded into a separate mic and
that each mic is individuall gated.
Patch the MDX2200 into a snare drum channel for example and adjust it so that triggering onl occurs on snare
hits. Each mic should be set to its maximum operating level, monitored (see SC MON switch) and the
THRESHOLD level set so that each snare hit sounds acousticall clean and seperate, as though it was pla ed
on its own.
The optimum use of the expander/gate depends principall on microphone technique. Be particularl careful,
when high frequenc instruments are located to the side or rear of a cardioid microphone. Most cardioids
exhibit a sharpl rising off-axis response characteristic at higher frequencies. If there is onl a 2 or 3 dB
difference between the on-axis and off-axis response in the 5 to 10 kHz region, c mbals ma leak excessivel
into the tom mics and ou ma have hi-hat spilling all over the snare mic.
Please make full use of the directional characteristic of the mics, to acousticall exclude all other instruments
as much as possible. Make sure that ou do ever thing possible to achieve source separation with good
microphone technique. Otherwise the expander/gate is not able to undertake clear acoustic separation.
Sometimes, it is necessar to prevent the expander/gate from responding to low frequencies (rumbles etc.),
especiall if a singer is moving the microphone around on a mic-stand. More information about this topic in
chapter 6.2.
4.2.2 Initial settings for the expander/gate section
lortnoC gnitteS
lortnocDLOHSERHTFFO
hctiwsESAELERWOLS
lortnocOITAR2:1
Tab. 4.1: Initial settings for the expander/gate se tion
Begin with ver low threshold levels, so that the signal can pass through the unit unaffected. Now turn the
control clockwise until all unwanted noise is removed and onl the sound of the desired instrument can be
heard.
To adapt the unit to the program material properl , ou can additionall choose between a SLOW or FAST
release time. In the depressed position, the unit works at a slow release time. Percussive material with little or
no reverb, is processed in fast mode, whereas the slow mode is advantageousl used for signals with long
durations or signals with heav ambience. You will find that a fast release time (FAST mode) is preferable for
acoustic separation of most percussive sounds, whilst c mbals and tom toms, normall benefit from the
SLOW mode.
The RATIO control determines the ratio between input and output level, for all signals below the selected point
of threshold. Use this control to determine whether the section works as an expander or as a gate (Ratio 1:8).
If the controls are set correctl , the drum sounds will be dr , sharp and clearl defined. If ou do not have
enough mics (or COMPOSER PRO channels!) to record each instrument separatel , tr to create sub-groups:
put the snare and mid-toms together, and group the side-toms, bass drum and c mbals together with the help
of a mixing console.
The aim is to set up the expander/gate and to position the group mics so that each strike on an instrument
opens a specific mic and so onl that instrument is recorded, whilst the other mics remain muted.
4. APPLICATIONS

18
COMPOSER PRO MDX2200
4.2.3 Reducing leakage in stage mics
The COMPOSER PRO has man uses in live-work, on stage and in multi-miking situations: a well set up
expander/gate can effectivel suppress background noise, compressor t pe pumping noise and microphone
leakage etc. without producing an undesirable side effects. Expander/gates are commonl used for process-
ing vocals. When specificall used with a compressor, the distance and position of the mic in relation to the
singer is ver critical: the further the distance, the more sensitive the mic is to background noise. Use the
expander/gate section in the slow release mode to inaudibl  eliminate background noise, that occurs in
pauses between singing. When used in live situations, leakage of miked instrumentation is substantiall
reduced, as well as other acoustic contaminants in various recording situations.
4.2.4 Reducing feedback in stage mics
When a singer is using a vocal mic, their voice effectivel stops other sounds from entering the mic. But in
pauses between the singing, the mic will pick up noise from the house PA and monitors, which can lead to
unpleasant feedback problems. If the COMPOSER PRO is inserted into the mic channel, it will shut off the
channel when it is not being used, reducing the possibilit of feedback. Principall all mics should be included
in this application.
4.2.5 Noise reduction on effects paths
The effects rack is one of the main overlooked sources of noise in a PA s stem or recording facilit . The price
of reverb and dela units and harmonizers has fallen drasticall over the last number of ears, which have made
these units a common feature in small studios and home recording installations. However, multiple effects
units considerabl increase the overall noise level, so that the pleasure in acquiring a new sound effect is short
lived.
It will prove useful to use the BEHRINGER COMPOSER PRO as the last component in the chain of effects
units and use the noise reduction function of the expander/gate section. We recommend that ou use a slow
release time in order to maintain the natural reverb.
4.2.6 Creative use of the expander/gate section
In addition to the previousl explained applications, the expander/gate can be used to change the sound
characteristics. For example, the qualit of ambience or reverberation created b an instrument within a room
can be modified: when an instrument stops deca ing, the reverberation of the instrument falls below the user-
defined threshold. The reverberation can be controlled b using the THRESHOLD control and the RELEASE
switch. The deca characteristics of the instrument can be controlled using the release switch, so that the
natural characteristics of the instrument remains. Experiment with the effect, this control has on the deca of
the instrument. In SLOW mode, the signal is gentl faded out - in FAST mode, the duration of the reverberation
can be removed completel .
.3 Compressor section
The task of a compressor is to reduce the d namic range of program material and to control the overall level.
The extensive controls of the compressor section, provide a great range of d namic effects: from musical and
soft compression to limiting signal peaks, right up to extreme and effective compression of the overall d nam-
ics. For example, a low ratio and ver low threshold setting can be used to achieve soft and musical processing
of the general d namics of the program material.
Higher ratios, together with low threshold settings, create relativel constant volume (levelling) for instruments
and vocals. High threshold levels generall limit the overall level of a program. Ratios greater than 6:1 effectivel
prevent the output level from significantl exceeding the threshold point (provided that the OUTPUT control is in
the 0 dB position).
Please note that the compression of the entire program material (achieved b low threshold settings) sounds
less natural with higher ratio settings. Ratio settings in the range of 4:1 and lower, effect the d namics of the
program material less and are often used to compress the sound of a bass guitar, a snare drum or a vocal.
Sensitive and moderate settings are generall used in mixing and for levelling of program material in broadcast.
5. APPLICATIONS

19
COMPOSER PRO MDX2200
Threshold Gain 0 dB
Input
Output
oo:1
Limiter
Ratio 2:1
Ratio 4:1
Hard Knee
green yellow red
IKA Curve
LED
Fig. 4.2: IKA hara teristi of the ompressor se tion
The new IKA (Interactive Knee Adaptation) circuit prevents aggressive compression, created b high ratios,
from sounding too unnatural. This is achieved with an interactive control function, which begins above the
threshold level and introduces a Soft Knee curve characteristic in the range up to 10 dB above the threshold
point. Be ond this range, the signal is subjected to linear (Hard Knee) compression.
+With the threshold control completel turned to the right, the threshold value is +20 dB. Since such a
value will not be reached in practice, ou can use it to disable the compressor section and work exclu-
sivel with the expander/gate and limiter circuits.
4.3.1 Initial settings for the compressor section
lortnoC gnitteS
hctiwsTUO/NINI
hctiwsTECSTUO
hctiwsNOMCSTUO
hctiwsEVITCARETNINI
hctiwsRETLIFCSTUO
lortnocDLOHSERHTBd02+
lortnocOITAR1:3
hctiwsOTUANI
lortnocTUPTUOBd0
Tab. 4.2: Initial settings for the ompressor se tion
Rotate the THRESHOLD control counterclockwise until an appropriate amount of gain reduction is indicated on
the GAIN REDUCTION meter. This operation will be accompanied b an audible drop in output level. The
OUTPUT control should now be turned clockwise to reinstate the output level. The level of the unprocessed and
the processed signal can be compared b pressing the I/O METER switch and observing the INPUT/OUTPUT
LEVEL meter.
Final adjustments of the controls can then be made to suit our particular requirements, including the RATIO,
ATTACK and RELEASE controls. The AUTO function of the attack and release times, provides program
dependent d namic processing which suits most standard uses. If a condensed or wider sound processing
4. APPLICATIONS

20
COMPOSER PRO MDX2200
technique is required, the attack and release times can also be manuall adjusted.
The experienced user will be in a position to specif parameters while in b pass mode and thus realize the
effect before the unit is actuall switched into operation. This is important in live situations, where a signal
needs to be managed efficientl b the engineer, without the convenience of continual A/B comparison.
4.3.2 The COMPOSER PRO as a sound effects unit
In the earl 1960s, musicians began looking at the recording process as a wa to create new sounds. The
pumping effect which had been avoided b earlier engineers suddenl became fashionable and was utilized as
a creative tool, la ing the groundwork for man of the sounds which are now considered indispensable in
contemporar music. The compressor is used in this role because ou can hear it working, and control of the
d namic range is of secondar importance.
The BEHRINGER COMPOSER PRO, with its extensive range of functions, is well suited to this application.
Sound effects of this kind can be achieved using extreme settings. To achieve this, set the THRESHOLD
control to a fairl low level, the RATIO control to almost maximum and use the ATTACK and RELEASE
controls to obtain the desired effect. Experiment with all the controls in order to get a feel of their function!
4.3.3 The muffling effect of a compressor
Quite often, compressors are sometimes accused of muffling the sound, whilst at the same time reducing the
d namics. This fact should be investigated further. Bass frequencies contain most of the energ within music
and therefore cause the compressor to reduce the overall d namics. If the music also contains high frequen-
cies along with the bass frequencies, these are also reduced in level. This is the reason wh : in an extremel
compressed recording of drums, the c mbals and high-hats are acousticall swamped b the sound of the
snare or the bass drum. The same effect is experienced when processing reverberated or ambient sounds. The
solution commonl used to this basic problem is either to reduce the compression ratio or to slow down the
attack time, so that the increasing high frequenc transients pass through the compressor unhindered before
the compressor takes effect.
The COMPOSER PRO MDX2200 offers a solution to this problem that is b much more elegant. The SC
FILTER switch allows ou to activate a high-pass filter in the control signal path of the compressor. This filter
makes sure that midrange and treble range frequencies are taken into account to a greater extent, and that a
low-frequenc signal triggers less compression than a midrange/treble signal of comparable level. A major
advantage of this design can be seen in the fact that the frequenc response of the overall signal is not modified
below the threshold adjusted with the Threshold control.
In pop music the d namics of both kick drum and bass guitar are usuall processed individuall . The side-
chain filter is therefore ideall suited to appl overall compression in the mix-down, to compress the music
while increasing its loudness, but without having to accept the drawbacks described above.
Please note that we offer a whole series of high-grade equalizers and enhancers/exciters, which are perfect
tools to give an d namics-processed signal the finishing acoustic touch. Please ask for detailed information!
. Peak limiter section
As a section of its own and independent of the remaining control functions, the peak limiter enables ou to limit
the maximum peak level on the COMPOSER PROs output. It has been designed for use in combination with
the compressor section. Independentl of all compressor functions, ou can protect subsequent devices against
signal peaks, short-time overload and excess modulation (radio stations, etc.).
4. APPLICATIONS