Behringer EURODESK MX9000 User's User manual

EURODESK®MX9000
www.behringer.com
Version 1.0 June 2000
User´s Manual
ENGLISH

2
Thissymbol,whereveritappears,alerts
you to the presence of uninsulated
dangerousvoltageinsidetheenclosure
- voltage that may be sufficient to
constitute a risk of shock.
This symbol, wherever it appears, alerts
you to important operating and
maintenance instructions in the
accompanying literature. Read the
manual.
SAFETY INSTRUCTIONS
CAUTION: To reducetheriskofelectricalshock,donotremove
thecover (or back). Nouser serviceable parts inside;
refer servicing to qualified personnel.
WARNING: To reduce the risk of fire or electrical shock, do not
expose this appliance to rain or moisture.
DETAILED SAFETY INSTRUCTIONS:
All the safety and operation instructions should be read before the appliance is operated.
Retain Instructions:
The safety and operating instructions should be retained for future reference.
Heed Warnings:
All warnings on the appliance and in the operating instructions should be adhered to.
Follow instructions:
Alloperationanduser instructions should be followed.
Water and Moisture:
The appliance should not be used near water (e.g. near a bathtub, washbowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool etc.).
Ventilation:
The appliance should be situated so that its location or position does not interfere with its proper ventilaton.
For example, the appliance should not be situated on a bed, sofa rug, or similar surface that may block the
ventilation openings: or placed in a built-in installation, such as a bookcase or cabinet that may impede the
flowofairthroughthe ventilation openings.
Heat:
The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other
appliance (including amplifiers) that produce heat.
Power Source:
Theapplianceshould be connected to a power supply onlyofthe type described in the operating instructions
or as marked on the appliance.
Grounding or Polarization:
Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.
Power-Cord Protection:
Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords and plugs, convenience receptacles and the point
where they exit from the appliance.
Cleaning:
The appliance should be cleaned only as recommended by the manufacturer.
Non-use Periods:
The power cord of the appliance should be unplugged from the outlet when left unused for a long period of
time.
Object and Liquid Entry:
Careshould be takenso that objectsdonot fall andliquids are notspilledinto the enclosurethrough openings.
Damage Requiring Service:
The appliance should be serviced by qualified service personnel when:
- The power supply cord or the plug has been damaged; or
- Objects have fallen, or liquid has been spilled into the appliance; or
- The appliance has been exposed to rain; or
- The appliance does not appear to operate normally or exhibits a marked change in performance; or
- The appliance has been dropped, or the enclosure damaged.
Servicing:
The user should not attempt to service the appliance beyond that is described in the Operating Instructions.
All other servicing should be referred to qualifield service personnel.

3
FOREWORD
DearCustomer,
Welcome to the team of EURODESK users and thank you very much for expressing your confidence in
BEHRINGERproducts by purchasing the MX9000.
It is one of my most pleasant tasks to write this letter to you, because it is the culmination of many months of
hard work delivered by our engineering team to reach a very ambitious goal: making an outstanding device
that will become a standard tool used by studios and P.A. companies. The task to design the EURODESK
certainlymeanta great deal of responsibility, which we assumedbyfocusingon you, the discerning user and
musician.Italsomeantalot of work and night shifts to accomplish this goal. But it was fun, too. Developing a
productusually brings a lot ofpeopletogether, and what a greatfeelingitis when everybody who participated
in such a project can be proud of what we’ve achieved.
Itis ourphilosophyto share ourjoy with you,because you arethe most importantmember of theBEHRINGER
family. With your highly competent suggestions for new products you’ve greatly contributed to shaping our
company and making it successful. In return, we guarantee you uncompromising quality (manufactured
under ISO9000 certified management system) as well as excellent technical and audio properties at an
extremely favorable price. All of this will enable you to fully unfold your creativity without being hampered by
budgetconstraints.
Weare often asked how we can make ittoproduce such high-grade devices at such unbelievably lowprices.
The answer is quite simple: it’s you, our customers! Many satisfied customers means large sales volumes
enablingus to get better conditions of purchase for components, etc. Isn’t it only fair to pass this benefitback
to you? Because we know that your success is our success, too!
I would like to thank all people whose help on “Project EURODESK MX9000” has made it all possible.
Everybody has made very personal contributions, starting from the designers of the unit via the many staff
members in our company to you, the user of BEHRINGER products.
My friends, it’s been worth the trouble!
Thank you very much,
UliBehringer

4
TABLE OF CONTENT
1. THE MANUAL..........................................................................................................................6
1.1 Nomenclature.................................................................................................................................. 6
1.2 Anun-holstic approach ................................................................................................................... 6
1.3 Key................................................................................................................................................. 6
2. EURODESK OVERVIEW ........................................................................................................6
2.1 Architecture .................................................................................................................................... 6
2.2 Metering.......................................................................................................................................... 7
2.3 PSU (Power SupplyUnit) ................................................................................................................ 7
3. INPUT/OUTPUT CHANNEL...................................................................................................8
3.1 Channelstrip................................................................................................................................... 8
3.2 Inputswitching ................................................................................................................................ 8
3.3 Inputgain setting ............................................................................................................................ 9
3.4 Mainequalizer .............................................................................................................................. 10
3.5 Aux sends .................................................................................................................................... 10
3.6 Routingand muting ........................................................................................................................11
3.7 B-channel ..................................................................................................................................... 12
4. INSERTS ...............................................................................................................................13
5. SUBGROUP AND DIRECT OUTPUTS ...............................................................................14
5.1 Subgroups .................................................................................................................................... 14
5.2 Directoutputs ............................................................................................................................... 16
6. MASTER PANEL ...................................................................................................................16
6.1 Aux masters ................................................................................................................................. 16
6.1.1 Aux sends .......................................................................................................................... 16
6.1.2 Aux returns ......................................................................................................................... 17
6.2 MIX-Bmaster ................................................................................................................................19
6.3 Monitoring ..................................................................................................................................... 20
6.4 Headphones.................................................................................................................................. 21
6.5 PFL/SOLO .................................................................................................................................... 22
6.5.1 PFL .................................................................................................................................... 22
6.5.1 SOLO ................................................................................................................................. 22
6.6 Talkback ....................................................................................................................................... 22
7. CONNECTIONS....................................................................................................................23
7.1 Rearpanel .................................................................................................................................... 23
7.2 Plugsolderingguide...................................................................................................................... 27
8. THE PATCHFIELD ................................................................................................................30
8.1 Thenormalizedbay....................................................................................................................... 30
8.2 Thepatchfield................................................................................................................................30
8.3 Loomingproblems......................................................................................................................... 32
9. EQUALIZATION .....................................................................................................................33
10.GAIN OPTIMIZATION ...........................................................................................................34
11.IMPEDANCES AND TUNING ...............................................................................................35
12.(UN)BALANCED LINES........................................................................................................35

5
13.START-UP.............................................................................................................................37
13.1A-channel setting upprocedure..................................................................................................... 37
13.1.1Selecting inputs .................................................................................................................. 37
13.1.2Initializingchannel for gain-setting....................................................................................... 37
13.1.3Auditioningasignal............................................................................................................. 37
13.2Desk/tape setting up procedures................................................................................................... 37
13.2.1Desknormalization ............................................................................................................. 37
13.2.2Multitrack initialization ........................................................................................................ 38
13.2.3Recordinglevels.................................................................................................................. 38
13.2.4Auditioning a mix ................................................................................................................ 38
13.2.5Mixermapping .................................................................................................................... 38
14.8-TRACK MIDI SUITE/DANCE PRODUCTION STUDIO ...................................................38
14.1Sends ........................................................................................................................................... 39
14.2Auxless headphones mix .............................................................................................................. 39
14.3Returns ......................................................................................................................................... 40
14.4Lining up record/sampleinputs...................................................................................................... 41
14.5Mixdown ....................................................................................................................................... 41
15.16-TRACK RECORDING WITH 2 SAMPLERS ...................................................................41
15.1Recording ..................................................................................................................................... 41
15.2Headphones.................................................................................................................................. 42
15.3Mixdown ....................................................................................................................................... 42
16.PROFESSIONAL 24-TRACK STUDIO ................................................................................42
16.1Recording ..................................................................................................................................... 42
16.2Verytricky headphones................................................................................................................. 43
16.3Wetmonitoring ............................................................................................................................. 44
16.4Mixdown ....................................................................................................................................... 44
17.LIVE P.A. WITH 2-TRACK RECORDING .............................................................................45
18.LIVE CONCERT WITH 24-TRACK RECORDING...............................................................46
19.EXPANDING THE EURODESK MX9000.............................................................................48
19.1Connections.................................................................................................................................. 48
19.2Alignment ..................................................................................................................................... 48
20.TIMECODE ...........................................................................................................................48
21.BOUNCING...........................................................................................................................49
22.SEQUENCING “LIVE” .........................................................................................................49
23.INPUT/OUTPUT CONFIGURATION ...................................................................................50
24.MODIFICATIONS ..................................................................................................................50
24.1Aux sends > post EQ ................................................................................................................... 51
24.2MIX-B source > postfader ............................................................................................................. 51
24.3LED meters > pre fader................................................................................................................. 51
25.SPECIFICATIONS.................................................................................................................52
26.WARRANTY ...........................................................................................................................54

6
1. THE MANUAL
1.1 Nomenclature
Most specialist subjects are not really all that difficult provided you understand the language used, and the
vocabulary of mixing is pretty straight-forward. Nevertheless it is as well to be clear about what certain terms
mean. A “slot” in a recorder will always be referred to as a TRACK, while that in a mixer will invariably be a
CHANNEL.A GROUP will always refer toasubmix of channels, never acollectionof musicians. Similarly the
termBAND willbe mentionedonlyin conjunctionwith FREQUENCY. Wewill attempttobe asunambiguous as
possible with terms, since much confusion can arise from sloppy definitions.
Sometermscan haveapluralityofmeanings. TRACK,inmixingparlance,refers toataperecorder.In electronic
circuits,components on a PCB(printed circuit board) arelinkedby flat conductorscalledTRACKS. Hopefully,
where terms have different meanings the contexts will be sufficiently diverse so as to avoid any possible
confusion.
1.2 An un-holstic approach
Itis virtuallyimpossible to fullyexplain oneaspectof amixingconsole (e.g.CHANNEL ROUTING) withoutalso
making it clear what those routes are, where they go, are they migratory, etc. That’s why we have
compartmentalisedthe EURODESK manual into sections, making iteasytofind problem solving information
and advice. You might find that several cross-sectional references have been made, where areas of interest
overlap.E.g.:ChannelEQ isspecified anddescribed inthe “Mainequalizer” section3.4, whileEQUALIZATION
has it’s own section, reflecting it’s importance and weight as a subject in it’s own right.
If we keep repeating ourselves concerning the use of B-channels and the MIX-B bus, it’s because a proper
understanding of this area of the board will greatly expand your mixing repertoire.
1.3 Key
All DESK functions will be numbered consistently throughout the manual, whether they be in the text or in an
illustration.In addition the following prefixes will be usedtodenotethe various types of function control inany
illustrations/textrespectively:
Prefix Meaning
SSwitch
LLED
P Potentiometer
F Fader
Tab. 1.1: Meaning of the used prefixes
Afterevery prefix youwill find theFUNCTION NUMBER. Numberingstartsat thetopof a CHANNEL,works its
way through a stereo GROUP, and finally through the MASTER SECTION. The phantom power and tape
operating level switches are not included in the numbering system.
2. EURODESK OVERVIEW
2.1 Architecture
TheEURODESKMX9000isahybridSPLIT/INLINEconsole.Inputchannelscovermostofthesurface fromthe
left, while the outputs to tape are to the right. Tape monitor returns, however, are housed within the channel
strips, not next to the tape outputs, as would be the case in a conventional “split” design. This architecture

7
enables much flexibility to be bestowed onto the tape monitor signal path, not least being its ability to pick up
functions easily from the main channel. Also, during mixdown, when tape tracks are no longer monitored but
MIXED, the signal path between tape input and main channel is kept to a minimum.
Theconfiguration is24 into8into 24.This meansthatthere are24 channels,eight subgroups or“submixes” (or
four stereo subgroups) and 24 tape monitor returns, one for each channel. There are 24 100 mm channel
faders, eight subgroup faders, and a stereo pair of faders driving the L/R main mix.
In remix mode 48 channels are available, all with EQ and access to the aux buses. There are six additional
stereo FX returns, giving a grand total of 60 separate line-level inputs: and that’s before you even consider
using the subgroup insert points to provide eight more!
Thereare six aux buses accessed byfourpotentiometers, two headphone mixes andprofessionalrecording,
monitoringandtalkback facilities. If you can afford to lose the extra 24 lineinputs,theMIX-Bbus can also act
as a separate stereo aux send, giving eight aux buses in all.
A comprehensive set of inputs and outputs include MIC (+48 V), line, tape (+4 dBu or -10 dBV), inserts all
round, direct channel outs and all master recorder and monitoring options. Just about everything you’d
expectfrom a massive console.
Inaddition,a1/4"jackexpanderbay (INPUTONLY) allowsdirect patchinginto allbuses withinthe EURODESK
(exceptPFL andSOLO). HencetwoEURODESKs maybe linked,orthe EURODESKcoupled toANY OTHER
CONSOLE,large or small, provided that the otherconsolehas (or can be MADE to have)similaraccess (see
section19 “EXPANDING THE EURODESK”).
Last, and probably least, two BNC connectors on top of the built-in meterbridge await optional gooseneck
desklights, available from allgoodgooseneck desk light stores.Amust for those darkenedauditoria,or when
you’re into your third consecutive night in the studio.
2.2 Metering
The 1 to 24 channels have signal (-20 dB, L25) and overload LEDs (PEAK, L24).
The bulit-in meterbridge provides 12 segment bargraph meters for all channels and subgroups as well as for
the main mix. By the DISPLAY MODE switch (S100, top left of the master section) you decide between
CHANNEL and TAPE MODE. Your choice will be indicated by a LED.
In CHANNEL MODE, which is the best for live mixing purposes, the LED meters read the channel’s direct
OUTPUT, which is post EQ, post mute and post fader (you may alter that to pre mute and pre fader by the
modificationdescribed inAPPENDIXII.3).
In TAPE MODE the channel meters will mirror the multitrack’s meters, because they read the tape reutrn
inputs– after theOPERATINGLEVEL switch, butunaffectedby anything elsehappeningin the channel.0dB
is referenced to the selected tape operating level (+4 dBu or -10 dBV).
Themain mixmetersdouble upasmono PFLorstereo SOLOmeters,or 2-trackreturnmeters, orEXTERNAL
return meters (in general, what you HEAR is what you SEE). During PFL/SOLO only the main mix bargraph
metersilluminate.
+In SOLO/PFL mode a 0 dB meter reading matches an internal operating level of 0 dBu (0.775 V).
However, when looking at the mix, 0 dB is referenced to +4 dBu, the 2-track operating level. I.e.
if only ONE signal is present in the main mix bus, SOLOing that signal will cause the meter
reading to increase by +4 dB.
2.3 PSU (Power Supply Unit)
Notan infectionof theurinarytract, infact PSUstandsfor theleast glamorous,mostfrequently underestimated
feature of any electronic device: the POWER SUPPLY UNIT. The EURODESK remote PSU connects to the
desk at the rear of the console via a multiway connector. 2 1/2 U high, nevertheless it is designed to slot into
a3U rack space.The extra 1/2Uis toallowair to circulatearound the heatsinksemployedfor heatdissipation.
If your control room is small, forget heating. The EURODESK PSU chucks out a massive 400 Watts.

8
Why? Any amplifier circuit is limited in it’s transient response by the available current. In common with most
desks of this size, the EURODESK has more than a thousand line-level operational amplifiers (op-amps)
inside. When being driven hard, many desks begin to show signs of stress due to power supply limitations.
Not so with the EURODESK MX9000. The sound should stay clean and crisp and TIGHT right up to the
operatinglimits of theop-ampsthemselves.
+Do not connect the PSU to the EURODESK while the PSU is connected to the mains supply.
3. INPUT/OUTPUT CHANNEL
3.1 Channel strip
Onthe EURODESK MX9000 the 24 INPUT +OUTPUT(I/O or “normal”) channels cover most oftheconsole.
Most of each strip is occupied by the main or A-CHANNEL, which can accept MIC, LINE or TAPE inputs,
depending on the positions of S1 and S3 (see fig. 3.1 and 3.2). Each channel strip also sports a secondary
B-CHANNEL (fig. 3.6) Anything routed to a B-channel is directed to a separate MIX-B bus. (See section 3.7
“B-channel” and also section 6.2 “MIX-B master”).
3.2 Input switching
Look first at the MIC/LINE switch S1. In the UP position it selects MIC. In the DOWN position LINE. The next
switch S3 chooses whether A-channel looks at INPUT or TAPE. If INPUT is routed to A-channel, TAPE is
offered to B-channel. If TAPE is routed to A-channel, INPUT is offered to B-channel. Depressing the PAD
switch (S1a) lowers an incoming mic signal by -20 dB, if necessary.
Fig. 3.1: Input
When track laying it is usual to use the MIX-B inputs for monitoring the signal from TAPE, while the
A-channels take care of microphones, Dl’s, etc. For MIXING purposes, TAPE tracks are normally “flipped”
onto the main channels, leaving the B-channels free for other applications, such as offerinq extra line inputs.
These rules are, however, made to be broken.
S23 applies to the B-channel only and replaces the normal TAPE or INPUT source with a tap from the main
channel,taken post mute andprefader. Now MIX-B actsasan extra stereo auxsend or extra stereomix.You
should remove MIX-B from the main mix (via S48, master section) in this configuration.

9
Fig.3.2:Channelinputswitchingarchitecture
+The B-channels 25 to 48 are only routable EN BLOC to the main mix, via S48. Therefore the
MIX-B bus can only have one function at any one time, either as a stereo AUX or secondary mix
send (S48 UP) or as a set of 24 extra line or tape inputs to the main mix (S48 DOWN).
3.3 Input gain setting
The channel input level is set by the TRIMPOT (P2). Use SOLO/PFL (S26) to bring the channel’s input onto
the L/R bargraph meters under the master section of the EURODESK MX9000. This also sends the SOLO/
PFLed signal to the left and right speakers. Channel PFL/SOLO (S26) has an associated LED (L26). (See
also 13.1 “A-channel setting up procedure” and 6.5 “Solo/PFL”.)
+For level-setting (as opposed to localized listening) choose to use the mono PFL rather than
the post fader SOLO bus (S95 DOWN).
+SOLO/PFL never interrupts the mix at the main recording outputs. It follows that aux sends
and subgroups must also be unaffected, since they can contribute directly to the main mix.
Inaddition to switchable PFL/SOLO metering, a couple ofLEDs(L24 and L25) continuously monitor whether
asignalis present (-20 dB) or the channel is going intooverload(PEAK).These take their cue from three test
points:input, post EQ and postfader.In all cases thehigherlevel wins. You do NOTwantthe overload light to
come on, or if it does no more than very intermittently during a take or a mix.

10
3.4 Main equalizer
Fig.3.3:Mainequalizer
Themain equalizer can beswitched(S10) out of circuitforeasy A/B comparisons betweenEQedand straight
signals,or for whenyouknow you don’twantto use desk EQat all. It isbest considered in threesections.First
offtherearetwo Baxendall shelving frequency controls for treble and bass, at 12 kHz and 80 Hz respectively
(P4and P9). These are DUPLICATEDforthe B-channel (P18 and P19),notmerely “SPLIT” off from themain
EQ. I.e. you can have a full 4-band EQ on the main channel AND a 2-band EQ on B-channel.
Secondly, there are two semi-parametric swept mids, Q fixed at 1, which cover the bands 300 Hz to 20 kHz
and 50 Hz to 3 kHz. An unusually broad frequency range is catered for, and there is an enormous 3-plus
octaveoverlap between thetwomid bands (P5,P6,P7 and P8).No experienced engineerwillcomplain about
that! All four bands offer 15 dB of cut and boost.
Thirdly there is a steep high pass (lo cut) filter (S11), slope @ 12 dB/octave, -3 dB @ 75 Hz, for reducing
floorrumble, plosives, woolly bottom end, etc.
3.5 Aux sends
All six aux sends are mono and post EQ. They are switchable PRE/POST fader in two banks (S13 and S16).
For aux sends 1 and 2, two dedicated pots (P12 and P13) are used. These can be taken from a point before
or after the channel fader, i.e. PRE or POST (S13). Aux sends 3 and 4, and 5 and 6 are serviced by two
potentiometers (P14 and P15). The SHIFT button (S15) determines whether buses 3 and 4 or 5 and 6 are
addressed. Also, these four sends can be derived from the main mix or MIX-B, depending on SOURCE
(S17), and, as before, can be pre or post (S16).

11
Fig. 3.4: Aux sends
+For almost all FX SEND purposes, you will want auxes to be post fader, so that when a fader
level is adjusted, any reverb send from that channel follows the fader. Otherwise, when the
fader is pulled down, the reverb from that channel would still be audible. For CUEing purposes,
aux sends will usually be set pre fader, i.e. independent of the channel fader (S13 and S16).
+Most reverbs etc. sum internally the left and right inputs. The very few that don’t may be driven
in true stereo either by 1) 2 aux sends or 2) the MIX-B bus (see section 3.7 “MIX-B”).
+There is +15 dB of gain on every aux send. Such a high boost is only appropriate where the
channel fader is set around -15 dB or lower. Here, an almost exclusively WET signal will be
heard. Previously, in most consoles, such a wet mix required the use of a PRE setting for the
channel auxiliary send. This meant losing fader control over the signal.
3.6 Routing and muting
ROUTINGmeans selecting which BUS you wantachannel to address. There areactuallysix stereo buses in
the EURODESK MX9000 (plus a stereo SOLO bus). The main mix bus is selected by S32 (see figure 3.5),
while the subgroups are selected by switches S28 (for groups 1 and 2), S29 (3 and 4), S30 (5 and 6) and
S31(7and 8). Odd and even numbered groups are selected via the mainA-channelPANP24,as are the left
and right mix buses. (The sixth stereo bus is the MIX-B bus, with it’s own independent pan control P20; see
section 3.7 “B-channel”). Usually, only one of S28 to S31 will be selected for a particular channel (See block
schematics).
+An exception to this rule is when laying down voice takes. It is often convenient to have the mic
channel(s) routed to alt potential TAKE tracks simultaneously, since you are often dropping in
quickly between four or more tracks. It means one less button press each time you switch
tracks.

12
Fig.3.5: Routing
Levelto thesubgroupand mainmixbuses isultimatelydetermined bythechannel faders.Theseare designed
togiveasmooth logarithmic taper of a type more usually associated with the name of some pretty expensive
brand... The low level performanceparticularlyis far smoother than thatofa normal “budget” fader.
TheMUTE button(S27),like thatfor SOLO hasan LEDindicator(L27) andremovesthe A-channelsignal from
allbuses,saveanyauxesset topre fader.It isergonomically placedimmediately abovethe faderand engaging
MUTEisequivalent to setting a fader level of minus infinity.
3.7 B-channel
The B-channel (fig 3.6) comprises a secondary channel with it’s own hi and lo EQ, pan and level (P18, P19,
P20 and P21). The EQ is a replica of the A-channel shelving EQ. The B-channel ALWAYS feeds into the
MIX-B stereo bus, but it’s source can be switched between TAPE, LINE, MIC and A-CHANNEL, depending
onhow S1, S3 andS23 are set (seefig.3.2 and section3.2).Unusually for an 8-busconsole,B-channels also

13
havetheirown MUTE buttons (S22). Aux sends 3/4/5/6 may bedivertedfromthe A to the B-channel via S17.
Thereforeif theB-channelis being usedto monitor off-tape,some FX processinge.g.reverb andechocan still
beapplied.(See section 16.3 “Wet monitoring”.)
+When B-channel looks at A-channel (S23 DOWN), the signal comes A-channel mute switch and
pre fader. A modification can convert this PRE stereo aux send to POST fader. (See APPENDIX
II “Modification No. 2”.)
Fig.3.6:B-channel
4. INSERTS
Insert points are useful for adding dynamic processing or equalisation to a channel, subgroup or the mix.
Unlike reverbs, etc., which are usually added to the dry signal, dynamic processing is normally applied
acrossan entiresignal. Here anaux sendwouldbe inappropriate.Instead thesignalis interceptedsomewhere
along the channel/subgroup/mix, fed through the dynamics processor and/or EQ and then returned to the
consoleat the same point where it left.Theinsert point is invisible or normalized, untilajack is plugged into it.
Allsubgroups and channels havegotinsert points, as doesthe main stereo output.BothSEND and RETURN
are accommodated on a single stereo 1/4" jack socket wired tip=send, ring=return. Inserts are always pre
fader and also pre EQ / aux sends for channels.
Insert points may also be used as pre EQ direct outputs without interrupting the signal flow. This is obvious
when looking at the patchbay wiring (section 8, fig. 8.1). If you want to insert a dynamics processor post EQ,
the insert point must either be taken from a subgroup, or via a second channel / aux return as follows:
a) Insert a compressor/gate/EQ across a subgroup, and route the channel to be processed (and only that
channel)tothat subgroup.
b) Alternatively, patcha channel’sdirect outinto acompressor/gate/EQ.Taketheoutputfromthat compressor/
gate/EQ and feed it back into the desk via a secondary input (channel, aux return, etc.).
Figure4.1illustrates howyoumightinsertinto achannel postEQfor mixdownor track-laying(theirrequirements
are different). Mixdown requires one A and one B-channel. Recording requires two A-channels.

14
Fig. 4.1: Post EQ channel insert
+In this arrangement you might find that compression tends to soften the perceived amount of
EQ applied. The solution? Apply more EQ. This creates a real “pressure” sound, great for high
energy music such as dance. (For a more subtle approach, use the desk insert points word for
word.)
+Using a group insert to effect post EQ processing precludes the use of POSTPROCESSING
AUX SENDS without some serious re-patching.
5. SUBGROUP AND DIRECT OUTPUTS
5.1 Subgroups
The principal routes to the multitrack are via the SUBGROUP OUTPUTS. There are four stereo (or eight
mono) subgroups, numbered 1 to 8. All main channels can access all of them, as can the STEREO AUX
RETURNS 1 and 2. (For this reason it is usually wise to bring your best two FX processors back on these
returns (or A-channels, for that matter), so that they can easily be sent to tape. (See also section 6.1 “Aux
masters”.)
Why are there 16 subgroup output jacks on the EURODESK when there are only 8 subgroups? Well, each
subgroupoutput is duplicated,sothat the EURODESKcan interface withupto 16 tracksviathe group outputs
withouthaving to re-patch.
As well as always functioning as subgroups for track laying via the SUBGROUP OUTPUTS, groups can be
routed directly into the main mix bus for submixing. Main mix routing is handled by switches S37 and S38.
S37 routes an odd numbered group to the left bus, while S38 sends an even numbered subgroup to the right
bus. That’s fine for stereo submixes. If instead you want a pair of mono submixes, press also the MONO
buttons(S35 and S36). Nowthese subgroups feed intothecenter of themainmix stereo image, i.e.equally to
L and R. You could have the first subgroup feeding into the left hand side, while the second one appeared in
mono, but I can’t think of many real situations when you’d want to do this.
Subgroup SOLO (S33 + S34) follows the mix assignment. E.g.: if the main mix is selected, then that stereo
subgroup will be monitored in stereo. If mono is also selected, monitoring is in mono.
+Try inserting compression / de-essing / an exciter / a gate across grouped signals (e.g. backing
vocals, drums, layered synths).

15
Fig. 5.1: Stereo subgroup channel schematic
+Try merging a dry signal with a little wet, then compressing the sum heavily. Though the
reverb proportion will be low when a signal is present, the resultant reverb tail pumped up by
the compressor at the start of each silence will give the illusion that the reverb was massive alt
the time. (The listener will be left wondering how the singer could sound so clear in such a wet
acoustic!)
+EURODESK insert points are, of course, simultaneously inputs and outputs. Get them onto a
patchbay, where they can appear as independent sockets, and do away with all these fiddly
Y-leads that always seem to be the first to get knotted in the flightcase. (See section 8
“Patchfield”.) Now it is possible to do the following incredibly useful patch without having to
make up what would amount to a ring-to-tip, tip-to-ring stereo patch lead.

16
Fig.5.2:Usinginsert toadd channelEQtosubgroupoutput (whilekeeping thenumberoflineinputsunchanged!)
5.2 Direct outputs
Eachof the24main channelson theEURODESKMX9000 hasitsown DIRECTOUTPUT, which istaken from
a point immediately after the fader (i.e. post EQ and after the aux sends, see block schematics). This can
feed a tape track directly without having to resort to the subgroups, enabling more than eight different tracks
tobe recorded simultaneously. Almostaloneamong the EUROjacks, these areon unbalanced mono sockets
at +4 dB. (See section 23, also section 16.1 “Recording”.)
6. MASTER PANEL
6.1 Aux masters
6.1.1 Aux sends
Much of the master section is taken up by master aux sends and returns. We’ll start with the sends (see fig.
6.1.1).
Stacked in a vertical column are six master aux send levels, one for each of buses 1 to 6 (P41 to P46). Each
has a gain structure of minus infinity to +15 dB. The extra 15 dB of gain comes in once a knob passes a
centerdetente (representing the “normal”unity gain position), enablinginsensitiveoutboard FX tobeproperly
driven. Each aux send has a SOLO button (S41 to S46), and, as with other areas of mixer, a LOCAL SOLO
LIGHT(L47), which illuminateswhen any oftheAUX master sendsaresolo-ed. Thisisto helpyousee exactly
what has been solo-ed. Any experienced engineer will have had occasion to search painstakingly through
every solo button on his/her console trying to find out why the main solo light was on, and the control room
monitorssilent!

17
Fig. 6.1: Aux sends
6.1.2 Aux returns
Next to the aux sends are the stereo aux returns (see fig. 6.2). These can be thought of as a dozen extra line
inputs configured as six stereo pairs. On these inputs there is up to 20 dB of gain available. Alternatively, a
mono(center-panned)signal may be returned by plugging into the left aux return jackonly.
+This feature is disabled if all line-level I/Os from the EURODESK are wired permanently to a
patchbay (see section 8).

18
^
Fig.6.2: Stereo aux returns

19
a) Aux returns 1 and 2
Aux returns 1 and 2 have full subgroup routing matrices to enable returning FX to be sent to tape, plus main
mix bus assignment. The functions for aux return 1 (mirrored by aux return 2) are: ROUTING (S49/50/51/52/
53) LEVEL (P49), BALANCE (P51) and SOLO (S54). LEVEL controls the amount of signal being blended
into the mix or a subgroup, while BALANCE controls the relative amounts of L and R processed signal. We
doubt if you’ll often want to adjust BALANCE away from center.
+As always, there are exceptions to the above rule. Some short stereo delay effects (say 30 ms
to L, 50 ms to right) cause a psychoacoustic effect where the earlier delay seems louder. A
similar effect is noticeable when harmonizing in stereo: a slight pitch shift upwards will seem
louder than one that goes down. In both cases use the BALANCE control (P51) to compensate.
+When carrying out the above mentioned information, or any other stereo imaging exercise,
don’t just rely on the control room monitors. Get a pair of headphones and listen in stereo and
in reverse stereo, to allow for any hearing discrepancy between your ears.
b) Aux returns 3 to 6
And so to aux returns 3 through 6. These too have a routing matrix (S55 to 58 for aux return 3), but this time
it is designed to facilitate monitoring rather than recording. The options are MAIN (L/ R) MIX, and PHONES
1/2. Gain pots and solo switches complete the picture.
c) SOLO
Below each column of aux returns lies a local solo LED (L61 & L74). These illuminate whenever a SOLO
button in the column above is pressed.
Thereisnoabsolutereasonwhythesendfromaux1shouldfeedintoaprocessorwhoseoutputsaresentto
the aux return 1. The processor could just as easily be patched into the aux return 3, or even a pair of
channels. For many purposes, however, it is sensible to set up a default patch where the aux outputs and
inputscorrespond. It is logical to put your premierFXunits into the aux 1 and aux2loops,since these returns
enable you to record to tape without re-patching.
+An exception to the above is when recording a group of performers live to multitrack. (See
section 16.3 “Wet monitoring”).
+Sometimes an engineer wants to narrow the stereo width of a reverb field. To do this you will
have to come back on either A or B-channels, which have full PAN facilities.
6.2 MIX-B master
Fig. 6.3: Mix-B
Only two controls occupy the MIX-B master (fig. 6.3). P48 offers the standard EURODESK gain of up to
+15 dB. S48 is crucial: it routes the MIX-B bus output into the main mix bus. MIX-B can have three basic
functions:
It can act as an entirely separate mixer-within-a-mixer to provide a completely separate mix (S48 UP, S23
DOWN). (See also section 17.)
It can act as an additional stereo aux feed to FX as well as a pre fader monitoring aid during mixdown (S48
UP, S23 DOWN).

20
It can provide 24 extra B-inputs to the mix (S48 DOWN, S23 UP).
+For live applications try using MIX-B to feed a secondary set of speakers. These could be
sidefills, or more spectacularly, the rearward portion of a quadraphonic sound system.
There is no SOLO provision for MIX-B. However, you can audition it by selecting only MIX-B (S83) in the
monitorsourcingmatrix.
+If MIX-B is assigned to the main mix (S48 DOWN), do not listen to MIX-B (S83) and the main mix
(S82) simultaneously. That way you’ll be monitoring MIX-B twice over, and what you hear
won’t correspond with what’s going down to tape.
6.3 Monitoring
Fig. 6.4: Monitoring
Though most of you will want to audition the main mix most of the time there are exceptions. These include
PFL/SOLO, and 2-TRACK PLAYBACK. The SOURCING matrix (S82 to S85, see fig. 6.4) allows you to
monitor the main mix, the MIX-B and two external sources marked 2-track and EXTERNAL. The master
meters follow whatever source is being auditioned. The meters won’t make much sense if more than one
source is selected!
+EXTERNAL could be “normalled” to a HiFi pre-amp, allowing you to monitor extra sources
such as vinyl, cassette, CD, etc.
+Altering what goes into the control room’s monitors does not affect the signal from the main
recording outputs. Just as well, or every time you wanted to do a quick SOLO during a mix,
you’d have to start again!