Behringer Eurogrand EG2180 User manual

EUROGRAND EG2180
Assembly Instructions
A50-95099-00001

EUROGRAND EG2180
Check that you have all of the following items2
Important Safety Instructions
The piano must be assembled before use. A Phillips or slotted screw driver is required to assemble the parts.=
The piano should be assembled by two persons to avoid injury due to its weight and bulky parts.=
During assembly, make sure you use the correct parts and screws and assemble them in the correct order.=
Use only screws that are included with the unit for assembly, otherwise the parts might get damaged.=
Insert the screws only into the holes/threads provided for this purpose. It is not necessary to drill additional holes.=
Be sure that all screws are tightened securely.=
To disassemble the unit, follow the steps in reverse order.=
The illustration below shows the designations of the parts supplied which are required for assembling the digital piano.=
Check that you have all of the following items1.
Item Quantity Item Quantity
{1} Keyboard 1 {6} Screws for Side Panel and Keyboard 4
{2} Side Panel (Left) 1 {7} Screws for Side Panel and Pedal Box 4
{3} Side Panel (Right) 1 {8} Screws for Modesty Panel 5
{4} Pedal Box 1 {9} Screws for Headphone Hanger 2
{5} Modesty Panel 1 [10] Headphone Hanger 1

EUROGRAND EG2180
Modesty Panel Assembly 3
Side Panel and Pedal Box Assembly2.
Position the Pedal Box1. {4} against the Left Side Panel {2} and then use two screws {7} to fasten the side panel. Finally, attach
a plastic cap to each screw.
Position the Pedal Box2. {4} against the Right Side Panel {3} and then use two screws {7} to fasten the side panel. Finally,
attach a plastic cap to each screw.
You can nd the pedal cable in the Pedal Box 3. {4}. Untie and straighten out the cable attached to the bottom of the Pedal Box.
Modesty Panel Assembly3.
Position the holes of the Modesty Panel1. {5} against the holes of the side panel brackets and then use two screws {8} with at-
tached washers to fasten the top of the Modesty Panel.
Use three screws2. {8} with attached washers to fasten the bottom of the Modesty Panel.
Use the cable clamp to take up any slack in the pedal cable.3.

EUROGRAND EG2180
Headphone Hanger Assembly4
Technical specications and appearance are subject to change without notice. The information contained herein is correct at the time of printing. All trademarks (except BEHRINGER,
the BEHRINGER logo, JUST LISTEN and EUROGRAND) mentioned belong to their respective owners and are not afliated with BEHRINGER. BEHRINGER accepts no liability
for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein. Colors and specications
may vary slightly from product. Products are sold through our authorized dealers only. Distributors and dealers are not agents of BEHRINGER and have absolutely no authority to
bind BEHRINGER by any express or implied undertaking or representation. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording of any kind, for any purpose, without the express written permission of BEHRINGER International GmbH.
ALL RIGHTS RESERVED. © 2008 BEHRINGER International GmbH,
Hanns-Martin-Schleyer-Str. 36-38,
47877 Willich-Muenchheide II, Germany.
Tel. [phone], Fax [phone]
Keyboard Assembly4.
Position the holes at the bottom of the Keyboard against the holes in the side panel brackets.1.
Use four screws2. {6} to fasten the Keyboard.
Insert the pedal cable connector into the pedal jack located at the rear of the Keyboard.3.
Be sure that the connector is inserted in the correct orientation. Make sure that the cable clamp fastens to the pedal+
cable.
Rotate the pedal adjuster until it comes in rm contact with the oor surface. If the adjuster is not in rm contact with +
the oor,the pedal will wobble and cause malfunctions.
Headphone Hanger Assembly5.
Use two screws1. {9} to fasten the Headphone Hanger [10] to
the underside of the Keyboard.
Pedal
Cable Jack
Headphones
Jack
Pedal adjuster
Screws to fasten
the keyboard with
side panel