Behringer EUROGRAND EG2080-RW User manual

Version1.0 December2006
Important safety and
assembly instructions
EUROGRAND EG2080-RW/BK

EG2080 ASSEMBLY
2
EG2080 OVERVIEW
Important Safety Instructions
VTheEG2080mustbeassembled beforeuse.A Phillipsorslotted screwdriveris requiredtoassemble the
parts.
VDuring assembly make sure you use the correct components and screws and assemble them in the
correctorder.
VThe piano should be assembled by two persons to avoid injury due to its weight and bulky parts.
VDuring assembly, make sure you use the correct parts and screws and assemble them in the correct
order.
VUse only screws that are included with the unit for assembly, otherwise the parts might get damaged.
VInsertthe screwsonly into theholes/threads providedforthis purpose.It isnotnecessary todrill additional
holes.
VBe sure that all screws are tightened securely.
VTodisassemblethe unit, follow the stepsinreverseorder.
VTheillustration below showsthedesignations of thepartssupplied which arerequired for assemblingthe
digitalpiano.
1. Check that you have all of the following items before assembly:

EG2080 ASSEMBLY
3
2. Side Panel and Pedal Box Assembly:
1. Positionthe Pedal Box againsttheLeft Side Panel and thenusetwo screws to fasten the side
panel. Finally, attach a plastic cap to each screw.
2. Position the Pedal Box against the Right Side Panel and then use two screws to fasten the
side panel. Finally, attach a plastic cap to each screw.
3. You can find the pedal cable in the Pedal Box . Untie and straighten out the cable attached to the
bottom of the Pedal Box.

EG2080 ASSEMBLY
4
3. Modesty Panel Assembly:
1. Positionthe holes of the ModestyPanel againstthe holes oftheside panel brackets and then usetwo
screws with attached washers to fasten the top of the Modesty Panel.
2. Use three screws with attached washers to fasten the bottom of the Modesty Panel.
3. Use the cable clamp to take up any slack in the pedal cable.
4. Keyboard Assembly:

EG2080 ASSEMBLY
5
1. Position the holes at the bottom of the Keyboard against the holes in the side panel brackets.
2. Use four screws to fasten the Keyboard.
3. Insert the pedal cable connector into the pedal jack located at the rear of the Keyboard.
Be sure that the connector is inserted in the correct orientation. Make sure that the cable clamp
fastens to the pedal cable.
Rotate the pedal adjuster until it comes in firm contact with the floor surface. If the adjuster is not
in firm contact with the floor,the pedal will wobble and cause malfunctions.
5. Headphone Hanger Assembly:
1. Use two screws to fasten the Headphone Hanger to the underside of the Keyboard.
Legal notice
Technicalspecifications andappearance subjectto changewithoutnotice. Theinformation containedherein is
correctat thetimeof printing.Alltrademarks (exceptBEHRINGER,the BEHRINGERlogo,JUST LISTENand
EUROGRAND) mentioned belong to their respective owners and are not affiliated with BEHRINGER. The
namesofcompanies,institutions orpublicationspicturedormentionedandtheirrespectivelogosaretrademarks
oftheirrespective owners.Their useneitherconstitutesaclaim ofthetrademarksbyBEHRINGER noraffiliation
of the trademark owners with BEHRINGER. BEHRINGER accepts no liability for any loss which may be
suffered by any person who relies either wholly or in part upon any description, photograph or statement
contained herein. Colours and specifications may vary slightly from product. Products are sold through our
authorised dealers only. Distributors and dealers are not agents of BEHRINGER and have absolutely no
authorityto bindBEHRINGERby anyexpressor impliedundertakingor representation.No part ofthis manual
maybereproducedor transmittedinanyformorbyanymeans,electronicormechanical,includingphotocopying
andrecordingofanykind, foranypurpose,withoutthe expresswritten permissionofBEHRINGERInternational
GmbH. ALLRIGHTS RESERVED.©2006 BEHRINGERInternational GmbH,
Hanns-Martin-Schleyer-Str.36-38, 47877Willich-MuenchheideII, Germany.
Tel.[phone], Fax [phone]