Behringer SYSTEM 100 182 User manual

Quick Start Guide
SYSTEM 100
182 SEQUENCER
Legendary Analog Sequencer
Module for Eurorack
Controls
(1) CH-1/CH-2 SEQUENCER COLUMNS – Use the knobs to
set the control voltage output for each step. Each column
sends out control voltages over a dedicated output
jack (CV OUT-1 and CV OUT-2). In PARALLEL mode,
two independent voltages can be set for each step for a
total of up to 8 steps. In SERIES mode, you can program
sequences of up to 16 steps.
(2) TEMPO – This knob controls the step speed of the
sequencer. The internal tempo clock can also be controlled
via the TEMPO CV IN jack. You can also route control
voltages from the CV OUT-1 or CV OUT-2 output jacks
back into the clock via the TEMPO CV IN jack to program
variable timing between each step.
(3) DELAY – Use this knob to set the amount of time taken
(0 to 10 seconds) to shift to the sequence’s next step
voltage, which is set by the 16 knobs in the CH-1/CH-2
SEQUENCER COLUMNS. The DELAY parameter creates
an eect similar to a portamento eect, except with an
exponential response. The DELAY function only operates
on the CV OUT-1 output jack (in both PARALLEL and SERIES
modes). The CV OUT-2 output jack is unaected by the
DELAY control.
(4) GATE TIME – This knob controls the length of time
the GATE OUT control voltage is active – known as the
“duty cycle” – in a range from 10% to 90%.
(5) STEP NUMBER – Rotate this knob to set the number of
steps counted before the sequencer re-starts. In PARALLEL
mode, the STEP NUMBER setting aects both columns
simultaneously. In SERIES mode, the STEP NUMBER setting
aects only the CH-2 row so that you may create longer
sequences of 9 to 16 steps.
(6) STEP (REPEAT/SINGLE) – This sliding switch determines
how the sequencer responds to triggering. In the REPEAT
setting, the sequence repeats every time it reaches the
end. The SINGLE setting stops the sequence after one full
cycle. The middle STEP setting advances the sequence one
step each time a trigger control voltage is received a the
TRIG IN jack.
(7) START/STOP – Press this button to trigger or stop
the sequence.
(8) PARALLEL/SERIES – This sliding switching determines
whether each step of the CH-1 and CH-2 columns trigger
separately and simultaneously (PARALLEL) for sequences
of up 8 steps, or if the two columns trigger one after the
other (SERIES) with the CH-1 column triggering rst,
followed by the CH-2 column. In SERIES mode, you can
create sequences of 8 to 16 steps.
(9) CV OUT-1/CV OUT-2 – These jacks send out separate
control voltage signals for the CH-1 (CV OUT-1 jack)
and CH-2 (CV OUT-2 jack) columns. When in SERIES mode,
CV OUT-1 provides the 16-step output and the CV OUT-2
jack provides an 8-step output.
(10) TEMPO CV IN – This jack routes in a control voltage signal
to control the tempo clock.
(11) GATE OUT – This jack sends out a gate trigger signal for
every sequencer step via cables with 3.5 mm connectors.
(12) TRIG IN – This input allows you to route in a trigger
voltage via cables with 3.5 mm connectors.
(13) TRIG OUT – Use this jack to send out a trigger voltage
signal for use with other modules. This trigger voltage is
generated when the sequencer reaches its end step.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
V 1.0

Power Connection
The 182 ANALOG SEQUENCER module comes with the required
power cable for connecting to a standard Eurorack power supply
system. Follow these steps to connect power to the module. It
is easier to make these connections before the module has been
mounted into a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow small
adjustments to the positioning while you get them all aligned. After
the nal position has been established, tighten the screws down.
Specications
Inputs
Tempo CV input
Type 3.5 mm TS jack, DC coupled
Impedance 100 kΩ, unbalanced
Max input level +10 V
CV scaling 1 V/oct.
Trigger input
Type 3.5 mm TS jack, DC coupled
Impedance 30 kΩ, unbalanced
Max input level +10 V
Outputs
CV output
Type 2 x 3.5 mm TS jacks, DC coupled
Impedance 600 Ω, unbalanced
Max output level +5 V
Gate output
Type 3.5 mm TS jack, DC coupled
Impedance 600 Ω, unbalanced
Max output level +5 V
Trigger output
Type 3.5 mm TS jack, DC coupled
Impedance 3 kΩ, unbalanced
Max output level +5 V
Controls
Step CV level 0 V to +5 V
Tempo 0.14 Hz to 33 Hz
Delay 0 to 10 s
Gate time 10 % to 90 % duty cycle
Step number 1 to 8 steps
Step switch Repeat / manual / single
Start/stop switch Momentary
Parallel/series switch 8 step / 16 step
Power
Power supply Eurorack
Current draw 30 mA (+12 V), 30 mA (-12 V)
Physical
Dimensions 43 x 81 x 129 mm (1.7 x 3.2 x 5.1")
Rack units 16 HP
Weight 0.17 kg (0.37 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and other information are subject to change without notice. All trademarks are the property
of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy,Turbosound,TC Electronic,TC Helicon, Behringer, Bugera, Auratone and Coolaudio are
trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2020 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding MusicTribe’s LimitedWarranty,
please see complete details online at musictribe.com/warranty.