BEINAT STM001 User manual

Belonging to

User Guide
Thank you for choosing the BEINAT S.r.L. digital tool, model STM001.
This manual was designed to help you obtain the best results and efficiency from the product.
ImportantNote
Read these instructions carefully before use and always keep them within hands reach while using the
instrument.
The illustrations and texts shown on the screens in this manual may differ from those actually displayed
The brand products BEINAT S.r.L. comply with European Directives ROHS 2002/95/EC, REACH 1907/2006, BATTERIES AND ACCUMULATORS
2006/66/EC RAEE 2003/96/EC
Channel: Beinat gas solutions
Electricconnections alsoavailable on
Portable Printer STM001
The majorityof the portable devices manufactured by BEINATS.r.l. canbeused in conjunction with a printer,in order
to certify, using a slip, the result of the test preformed.
The printer ismainly used to checkgasdetection probes, for pressuregaugesand to issue the declaration of conformity.
BEINATS.r.l.adopted thistypeofthermalprinterasaninnovativesolution comparedtothesystemsthatuseanimpact-
based system. The elegant design, dimensions, and small weight, together with its flexibilitymake this printer auseful
working tool.
The printer can be interfaced with serial RS232 and IRDA transmission, and it is ideal to print the system control and
verification report, thus self-certifying your own work.
The size and weight are extremely small.
The automatic paper-load with “six-load” system is patented. Moreover, it is complete with paper-out sensor.

Page 2
Precautions
Read the following security precautions carefully to prevent any risk of product damage and personal
injury, and thoroughly once more before using the STM001 printer.
Keep them in a safe place so that they can be read by someone new before they use the
appliance.
Turn the appliance off in case of malfunctioning.
If you detect any smoke or pungent or unusual odour from the appliance or power supply (accessory
supplied),
turn it off immediately, disconnect it from the mains, and send it to the nearest Service Center.
Do not try to disassemble the appliance.
Contact with internal components can cause injury. In case of faults the product must only be repaired by
qualified personnel.
If the appliance is broken due to a fall or crash, contact the Service Center to repair it.
Observe due precautions while handling the batteries.
The batteries should never be exposed to high temperatures, that is, over +60°C.
In order to ensure an optimum service life, use them at environment temperature.
If used at low temperatures their service life could diminish.
Never take apart the batteries; do not throw them into fire as they could explode.
Do not dispose of the batteries as normal waste. Follow local regulations on their disposal.
Use the correct cables supplied.
To ensure product conforms to norms, only use the correct cables supplied or those marketed separately
by BEINAT S.r.l. for terminal input/output connection.
In order to achieve long and satisfactory use of your STM001 printer, use and store it by respecting the
following precautions.
CHECK the integrity of the printer after having removed it from the box.
Any use of the printer for purposes other than the intended one is considered improper, and as a result
of which BEINAT S.r.l. therefore disclaims any responsibility for possible damages caused to people,
animals or objects.
Do not allow it to become wet.
The printer can be seriously damaged as it is not waterproof either when immersed in water or exposed
to high levels of humidity.
Do not drop it.
Heavy knocks on hard surfaces and strong vibrations can damage the appliance.
Avoid strong magnetic fields.
This printer should not be used or stored near radiation, or intense magnetic fields. Static electricity or
magnetic fields generated by appliances such as radio transmitters can interfere during printing.
Avoid abrupt temperature fluctuations.
Sudden temperature variations can cause condensation and the batteries could supply a lower voltage.
Cleaning
Never clean the device with chemical products. If necessary, wash with a moist cloth.
For Your Security

Page 3
Concept and Battery Charging
Power supply .................................................................................. 4,8 Vdc through the built-in batteries
Type of batteries .............................................................................................. Rechargeable stylus AA
Consumption during printing .................................................................................................... 925 mA
Battery duration .......................................................................................................... 100 m of paper
Autonomy ........................................................................................................................ 1h 30 min
Paper roll size ............................................................................................................ 57.5 mm ± 1 mm
Paper-out sensors ................................................................................................................. Built in
Print method .......................................................................................................... Thermal 8 dot/mm
Printing mode .................................................................................................... Straight, reverse 90°
Receive buffer ....................................................................................................................... 128 bytes
Flash memory ............................................................................................................................. 32K
Print speed ....................................................................................................................... 40 mm/sec
Functioning temperature ................................................................................................... 0°C ÷ +50°C
Relative humidity ........................................................................................... 10-85% without condensation
Electromagnetic compatibility ........................................................................................................ CE
Size & weight .......................................................................................... 146*88*65 mm - about 370 g
Warranty ............................................................................................................................... 3 years
Battery technical data
Battery pack nominal voltage 4,8 V.
Duration about 1h 30 min. using charged batteries.
On the first turn on
On purchase, the batteries are not completely charged.
We recommend to charge the batteries for max. 6 hours, before using the instrument.
Always use the supplied battery charger. If it becomes faulty obtain and use the genuine original spare part.
Charging the batteries.
1. Connect the battery charger connector to the socket located at the side of the instrument.
2. Connect the battery charger to an electrical outlet. The front red LED will instantly turn on.
While charging, the battery level indicator will show the battery charge status.
Charge time: about 6 hours.
Use
The batteries should never be exposed to high temperatures, that is, over +60°C.
In order to ensure an optimum service life, use them at environment temperature.
If used at low or high temperatures their service life could diminish.
LED indication Condition Solution
ON Printer ON
Off Printer OFF
* No paper Insertpaper
* * Hot print head Cool down the print head
* * * Low battery Recharge the battery
* * * * Battery at 20% Rechargeimmediately
Blinking every second Quick charging
Technical Specifications

BE-Rev - 17 02
INSURANCE. This device is insured by the SOCIETÀ REALE MUTUA for the PRODUCT'S GENERAL LIABILITY
up to a maximum of 1,500,000.00 EURO against damages caused by the device in case of failures in functioning.
WARRANTY. The warranty term is 3 years from manufacturing date, in agreement with the following
conditions. The components acknowledged as faulty will be replaced free of charge, excluding the replacement
of plastic or aluminium cases, bags, packing, batteries and technical reports.
The device must arrive free of shipment charges to BEINAT S.r.l.
Defects caused by unauthorized personnel tampering, incorrect installation and negligence resulting from
phenomena outside normal functioning shall be excluded from the warranty.
BEINAT S.r.l. is not liable for possible damage, direct or indirect, to people, animals, or things; from product
faults and from its enforced suspension of use.
DISPOSAL OF OLD ELECTRICAL & ELECTRONIC EQUIPMENT.
This symbol on the product or its packaging to indicates that this product shall not be treated as household waste. Instead, it shall be handed over to
the applicable collection point for the recycling of electrical and electronic equipment, such as for example:
- sales points, in case you buy a new and similar product
- local collection points (waste collection center, local recycling center, etc...).
By ensuring this product is disposed of correctly, you willhelpprevent potential negative consequence for the environment and human health, which could
otherwise be caused by inappropriate waste handing of this product. The recycling of materials will help to conserve natural resources. For more detailed
information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased
theproduct.
Attention: in some countries of the European Union, the product is not included in the field of application of the National Law that applies the European
Directive 2002/96/EC and therefore these countries have no obligation to carry out a separate collection at the “end of life” of the product.
Business - [e-mail]
Help Desk - [e-mail]
BEINAT S.r.l.
Via Fatebenefratelli 122/C 10077, S. Maurizio C/se (TO) - ITALY
Tel. [phone] - Fax [phone]
http:// www.beinat.com
Madein Italy
Lo styling è della b & b design
Stamp and signature of the dealer
Date of purchase:
Serial number:
La Beinat S.r.l. following the purpose of improving its products, reserves the right to change the technical, aesthetic and functional characteristics
at any time and without giving any notice.
Printer STM001