Beko WMY 610322 User manual

2820524438/ 22-12-14.(9:17)
WMY 610322
Washing Machine
User’s Manual
Document Number

This product was manufactured using the latest technology in environmentally friendly conditions.

3 / EN
Washng Machne / User’s Manual
1 General safety nstructons
This section includes security instructions which may help prevent
the injuries and material damage risks. All kinds of warranties shall
be invalid if these instructions are not observed.
1.1 Lfe and property safety
u
Never place the product on a carpet-covered floor. Electrcal parts
wll get overheated snce ar cannot crculate from under the devce.
Ths wll cause problems wth your product.
u
Unplug the product f t s not n use.
u
Always have the nstallaton and reparng procedures carred out
by the Authorzed Servce Agent. Manufacturer shall not be held
lable for damages that may arse from procedures carred out by
unauthorzed persons.
u
The water supply and dranng hoses must be securely fastened and
reman undamaged. Otherwse, water leak may occur.
u
Whle there s stll water nsde the product, never open the loadng
door or remove the flter. Otherwse, rsk of floodng and njury from
hot water wll occur.
u
Do not force open the locked loadng door. Door can be opened a few
mnutes after the washng cycle ends. In case of forcng the loadng
door to open, the door and the lock mechansm may get damaged.
u
Use detergents, softeners and supplements sutable for automatc
washng machnes only.
u
Follow the nstructons on the label of textles and the detergent
package.
1.2 Chldren's safety
u
Ths product can be used by the chldren who are at the age of 8 and
over and the people whose physcal, sensory or mental sklls are not
fully developed or who do not have necessary requred experence
and knowledge as long as they are supervsed or traned about the
safe use of the product and ts rsks. Chldren should not play wth the
devce. Cleanng and mantenance works should not be performed
by chldren unless they are supervsed by someone. Chldren of less
than 3 years should be kept away unless contnuously supervsed.
u
Packagng materals may be dangerous for the chldren. Keep
packagng materals n a safe place away from reach of the chldren.
u
Electrcal products are dangerous for the chldren. Keep the chldren
away from the product when t s n use. Do not allow them to play

4 / EN
Washng Machne / User’s Manual
wth the product. Use chld lock to prevent chldren from ntervenng
wth the product.
u
Do not forget to close the loadng door when leavng the room where
the product s located.
u
store all detergents and addtves n a safe place away from the
reach of the chldren by closng the cover of the detergent contaner
or sealng the detergent package.
1.3 Electrcal safety
u
If the product has a falure, t should not be operated unless t s
repared by the Authorzed Servce Agent. Rsk of electrc shock!
u
Ths product s desgned to resume operatng n the event of
powerng on after a power nterrupton. If you wsh to cancel the
programme, see "Cancellng the programme" secton.
u
Plug the product nto a grounded outlet protected by a 16 A fuse. Do
not neglect to have the groundng nstallaton made by a qualfed
electrcan. Our company shall not be lable for any damages that
wll arse when the product s used wthout groundng n accordance
wth the local regulatons.
u
Do not wash the product by sprayng or pourng water onto t! Rsk of
electrc shock!
u
Never touch the power cable plug wth wet hands! Do not grab the
power cord to unplug the machne, always unplug t by holdng the
socket wth one hand, and pullng the plug wth the other hand.
u
Product should be unplugged durng nstallaton, mantenance,
cleanng and repar procedures.
u
If the power cable s damaged, t must be replaced by the
manufacturer, after sales servce or a smlarly qualfed person
(preferably an electrcan) or someone desgnated by the mporter n
order to avod possble rsks.
1.4 Hot surface safety
While washing the laundry at high
temperatures, the loading door glass
will get hot. Considering this fact, during
washing operation keep the children away
from the loading door of the product to
prevent them touching it.

5 / EN
Washng Machne / User’s Manual
2 Important instructions for environment
2.1 Compliance with WEEE Directive
This product complies with EU WEEE Directive (2012/19/EU). This product bears a
classification symbol for waste electrical and electronic equipment (WEEE).
This product has been manufactured with high quality parts and materials which
can be reused and are suitable for recycling. Do not dispose of the waste product
with normal domestic and other wastes at the end of its service life. Take it to the
collection center for the recycling of electrical and electronic equipment. Please
consult your local authorities to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not
contain harmful and prohibited materials specified in the Directive.
2.2 Package information
Packaging materials of the product are manufactured from recyclable materials in accordance
with our National Environment Regulations. Do not dispose of the packaging materials together
with the domestic or other wastes. Take them to the packaging material collection points
designated by the local authorities.
3 Intended use
• This product has been designed for domestic use. It is not for commercial
purposes or it should not be used out of its intended use.
• The product must only be used for washing and rinsing of laundry that are
marked accordingly.
• The manufacturer waives any responsibility arisen from incorrect usage or
transportation.
• The service life of your product is 10 years. During this period, original spare
parts will be available to operate the appliance properly.

6 / EN
Washng Machne / User’s Manual
4 Technical specifications
Suppler name or trademark Beko
Model name WMY 610322
Rated capacty (kg) 6
Maxmum spn speed (rpm) 1000
Heght (cm) 84
Wdth (cm) 60
Depth (cm) 41.5
Net weght (±4 kg.) 56
Sngle Water nlet / Double Water nlet • / -
• Avalable
Electrcal nput (V/Hz) 230 V / 50Hz
Total current (A) 10
Total power (W) 1550
Man model code 9213

7 / EN
Washng Machne / User’s Manual
4.1 Installation
• Apply to the nearest authorized service agent for the installation of your product.
• Preparation of the location and electrical, tap water and waste water installations at the place of
installation is under customer's responsibility.
• Make sure that the water inlet and discharge hoses as well as the power cable are not folded,
pinched or crushed while pushing the product into its place after installation or cleaning
procedures.
• Make sure that the installation and electrical connections of the product are performed by
authorized service. Manufacturer shall not be held liable for damages that may arise from
procedures carried out by unauthorized persons.
• Prior to installation, visually check if the product has any defects on it. If so, do not have it installed.
Damaged products cause risks for your safety.
4.1.1 Approprate nstallaton locaton
• Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other
similar surfaces.
• When the washing machine and drier are placed on top of each other, their total weight –when
loaded– amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient
load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product in the environments where the temperature falls below 0 ºC.
• Leave a minimum space of 1 cm between the machine and the furniture.
• On a graduated floor, do not place the product next to the edge or on a platform.
4.1.2 Removng packagng renforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by pulling the
ribbon. Do not make this operation alone by yourself.
4.1.3 Removng the transportaton locks
1 Loose all bolts with an appropriate wrench until they turn freely (C).
2 Remove the transport safety bolts by turning them slightly.
3 Insert the plastic covers in the bag containing the user manual to the openings on the rear
panel. (P)
A
CAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the
product will be damaged.
C
Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again
in the future.
Install the transport safety bolts in reverse order of the disassembly procedure.
Never move the product without the transportation safety bolts properly fixed in place!

8 / EN
Washng Machne / User’s Manual
4.1.4 Connectng water supply
C
The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have
10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a
pressure reducing valve if water pressure is higher.
If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the
supplied stopper to the hot water valve before operating the product. (Applies for the products supplied with a
blind stopper group.)
A
CAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the
laundry will get damaged or the product will switch to protection mode and will not operate.
CAUTION: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.
Connect the special water supply hoses supplied with the product to the water
inlets on the product. Red hose (left) (max. 90 ºC) is for hot water inlet, blue hose
(right) (max. 25 ºC) is for cold water inlet.
Make sure that the hot and cold water taps are connected correctly when the
product is being installed. Otherwise, your laundry will come out hot at the end of
the washing process and wear out.
1 Tighten the nuts of the hose by hand. Never use a tool when
tightening the nuts.
2 When hose connection is completed, check whether there is
leak problems at the connection points by opening the taps
fully. If any leaks occur, turn off the tap and remove the nut.
Retighten the nut carefully after checking the seal. In order to
prevent the water leaks and resultant damages, keep the taps
closed when you do not use the product.
4.1.5 Connectng the dran hose to the dran
• Attach the end of the drain hose directly to waste water drain, lavatory or bathtub.
A
CAUTION: Your drain house will be flooded if the hose comes out of its housing during water discharge.
Moreover, there is risk of scalding due to high washing temperatures! In order to prevent such situations and
make sure that the machine performs water intake and discharge processes without any problem, fix the drain
hose securely.
100cm
40cm
• Connect the drain hose to a minimum height of 40
cm and a maximum height of 100 cm.
• In case the drain hose is elevated after laying it on
the floor level or close to the ground (less than 40 cm
above the ground), water discharge becomes more
difficult and the laundry may come out excessively
wet. Therefore, follow the heights described in the
figure.
• To prevent the waste water to go back into the machine again and to ensure easy drainage, do not
immerse the end of the hose into the waste water or do not insert it into the drain for more than
15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not be stepped on and the hose must not be
pinched between the drain and the machine.
• If the length of the hose is too short, use it by adding an original extension hose. Length of the
hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the
extension hose and the drain hose of the product must be fitted well with an appropriate clamp as
not to come off and leak.

9 / EN
Washng Machne / User’s Manual
4.1.6 Adjustng the feet
A
CAUTION: In order to ensure that the product operates more silently and vibration-free, it must stand level
and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its
place and cause crushing and vibration problems.
CAUTION: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.
1 Loosen the lock nuts on the feet by hand.
2 Adjust the feet until the product stands in a stable and balanced way.
3. Tighten all lock nuts by hand again.
4.1.7 Electrcal connecton
Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable
for any damages that will arise when the product is used without grounding in accordance with the
local regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after installation.
• If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified
electrician install a 16 Amp fuse.
• The voltage specified in the "Technical specifications" section must be equal to your mains
voltage.
• Do not make connections via extension cables or multi-plugs.
B
CAUTION: Damaged power cables must be replaced by the Authorized Service Agents.
4.1.8 Intal use
Before starting to use the product make sure that the preparations
are made which are in line with the “Important Safety and
Environment Instructions” and the instructions in the “Installation”
section.
To prepare the product for washing laundry, perform first operation
in Drum Cleaning programme. If this program is not available in your
machine, apply the method which is described in the section 4.4.2.
C
Use an anti-limescale suitable for the washing machines.
Some water might have remained in the product due to the quality control processes in the production. It is not
harmful for the product.

10 / EN
Washng Machne / User’s Manual
4.2 Preparation
4.2.1 Sortng the laundry
* Sort laundry according to type of fabric, color, and degree of soiling and allowable water
temperature.
* Always obey the instructions given on the garment tags.
4.2.2 Preparng laundry for washng
• Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons
will damage the machine. Remove the metal pieces or wash the clothes by putting them in a
laundry bag or pillow case.
• Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside
out and brush. Such objects may damage the product or cause noise problem.
• Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case.
• Place curtains in without compressing them. Remove curtain attachment items.
• Fasten zippers, sew loose buttons and mend rips and tears.
• Wash “machine washable” or “hand washable” labeled products only with an appropriate
programme.
• Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash
them separately.
• Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.
• Only use the dyes / color changers and descaling agents which are appropriate to machine wash.
Always follow the instructions on the package.
• Wash trousers and delicate laundry turned inside out.
• Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will
reduce pilling.
• Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must
be shaken off before placing into the machine. Such dusts and powders on the laundry may build
up on the inner parts of the machine in time and can cause damage.
4.2.3 Thngs to be done for energy savng
Following information will help you use the product in an ecological and energy-efficient manner.
• Operate the product in the highest capacity allowed by the programme you have selected, but do
not overload; see, "Programme and consumption table". See, “Programme and consumption table"
• Always follow the instructions on the detergent packaging.
• Wash slightly soiled laundry at low temperatures.
• Use faster programmes for small quantities of lightly soiled laundry.
• Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.
• If you plan to dry your laundry in a dryer, select the highest spin speed recommended during
washing process.
• Do not use more detergent than the recommended amount specified on its package.
4.2.4 Loadng the laundry
1. Open the laundry cover.
2. Put the laundry items into the machine in a loose manner.
3. Push and close the loading cover until you hear the locking sound. Ensure that no items are caught
in the door. The loading door is locked while a programme is running. The door can only be opened
a while after the programme comes to an end.
4.2.5 Correct load capacty
The maximum load capacity depends on the type of laundry, the degree of soiling and the washing
programme desired.
Machine automatically adjusts the water amount according to the weight of the laundry put inside it.
A
WARNING: Follow the information in the “Programme and consumption table”. When overloaded, machine's
washing performance will drop. Moreover, noise and vibration problems may occur.

11 / EN
Washng Machne / User’s Manual
4.2.6 Usng detergent and softener
C
When using detergent, softener, starch, fabric dye, bleacher and decolorant, descaling agents; read the
manufacturer's instructions written on the package and follow the dosages specified. Use measuring cup if
available.
1
3
2
The detergent drawer is composed of three
compartments:
– (1) for prewash
– (2) for main wash
– (3) for softener
– ( ) in addition, there is a siphon piece in the
softener compartment.
Detergent, softener and other cleaning agents
• Add detergent and softener before starting the washing programme.
• While the washing cycle is in progress, do not leave the detergent dispenser open!
• When using a programme without prewash, do not put any detergent into the prewash
compartment (compartment nr. "1").
• In a programme with prewash, do not put liquid detergent into the prewash compartment
(compartment nr. "1").
• Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place
the detergent bag or the dispensing ball directly among the laundry in the machine.
If you are using liquid detergent, do not forget to place the liquid detergent container into the main
wash compartment (compartment number “2”).
Choosing the detergent type
Detergent type to be used depends on the fabric type and color.
• Use different detergents for coloured and white laundry.
• Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.)
used solely for delicate clothes.
• When washing dark coloured clothes and quilts, it is recommended to use liquid detergent.
• Wash woolens with special detergent made specifically for woolens.
A
CAUTION: Use only detergents manufactured specifically for washing machines.
CAUTION: Do not use soap powder.
Adjusting detergent amount
The amount of washing detergent to be used depends on the amount of laundry, the degree of
soiling and water hardness.
• Do not use amounts exceeding the dosage quantities recommended on the detergent package
to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental
protection.
• Use lesser detergent for small amounts or lightly soiled clothes.
Using softeners
Pour the softener into the softener compartment of the detergent drawer.
• Do not exceed the (>max<) level sign on the softener compartment.
• If the softener has lost its fluidity, dilute it with water before putting it in the detergent drawer.

12 / EN
Washng Machne / User’s Manual
Using liquid detergents
If the product contains a liquid detergent cup:
• Put the liquid detergent container into the
compartment no “2”.
• If the liquid detergent lost its fluidity, dilute
it with water before putting it into the
detergent container.
If the product does not contain a liquid detergent cup:
• Do not use liquid detergent for the prewash in a programme with prewash.
• Liquid detergent stains your clothes when used with Delayed Start function. If you are going to
use the Delayed Start function, do not use liquid detergent.
Using gel and tablet detergent
• If the gel detergent thickness is fluidal and your machine does not contain a special liquid
detergent cup, put the gel detergent into the main wash detergent compartment during first
water intake. If your machine contains a liquid detergent cup, fill the detergent into this cup before
starting the programme.
• If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly
into the drum before washing.
• Put tablet detergents into the main wash compartment (compartment nr. "2") or directly into the
drum before washing.
Using starch
• Put the liquid soda, powder soda or the fabric dye into the softener compartment.
Do not use softener and starch together in a washing cycle.
Wipe the inside of the machine with a damp and clean cloth after using starch.
Using limescale remover
• When required, use limescale removers manufactured specifically for washing machines only.
Using bleaches
Add the bleach at the beginning of the washing cycle by selecting a prewash program. Do not put
detergent in the prewash compartment. As an alternative application, select a programme with
extra rinse and add the bleaching agent while the machine is taking water from the detergent
compartment during first rinsing step.
• Do not use bleaching agent and detergent by mixing them.
• Use just a little amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as it
causes skin irritation. Do not pour the bleach onto the laundry and do not use it with the colored
items.
• When using oxygen-based decolorant, select a program which washes the laundry at a low
temperature.
• Oxygen-based decolorant can be used with the detergent; however, if it is not at the same
consistence, first put detergent in the compartment number “2” in the detergent dispenser and
wait for the machine to flush the detergent when taking in water. While the machine continues
taking in water, add decolorant in the same compartment.

13 / EN
Washng Machne / User’s Manual
4.2.7 Tps for effcent washng
Clothes
Light Colours and
Whites Colours Black/Dark Colours
Delicates/
Woolens/
Silks
(Recommended temperature
range based on soiling level:
40-90 oC)
(Recommended temperature
range based on soiling level:
cold -40 oC)
(Recommended
temperature range
based on soiling level:
cold -40 oC)
(Recommended
temperature range
based on soiling
level: cold -30 oC)
Soiling Level
Heavily
Soiled
(difficult stains
such as grass,
coffee, fruits
and blood.)
It may be necessary to pre-
treat the stains or perform
prewash. Powder and liquid
detergents recommended
for whites can be used at
dosages recommended for
heavily soiled clothes. It is
recommended to use powder
detergents to clean clay and
soil stains and the stains that
are sensitive to bleaches.
Powder and liquid detergents
recommended for colors can be
used at dosages recommended
for heavily soiled clothes. It is
recommended to use powder
detergents to clean clay and
soil stains and the stains that
are sensitive to bleaches. Use
detergents without bleach.
Liquid detergents
suitable for colors
and dark colors can
be used at dosages
recommended for
heavily soiled clothes.
Prefer liquid
detergents
produced for
delicate clothes.
Woolen and silk
clothes must
be washed with
special woolen
detergents.
Normally
Soiled
(For example,
stains caused
by body on
collars and
cuffs)
Powder and liquid detergents
recommended for whites
can be used at dosages
recommended for normally
soiled clothes.
Powder and liquid detergents
recommended for colors can be
used at dosages recommended
for normally soiled clothes.
Detergents which do not
contain bleach should be used.
Liquid detergents
suitable for colors
and dark colors can
be used at dosages
recommended for
normally soiled
clothes.
Prefer liquid
detergents
produced for
delicate clothes.
Woolen and silk
clothes must
be washed with
special woolen
detergents.
Lightly
Soiled
(No visible
stains exist.)
Powder and liquid detergents
recommended for whites
can be used at dosages
recommended for lightly soiled
clothes.
Powder and liquid detergents
recommended for colors can be
used at dosages recommended
for lightly soiled clothes.
Detergents which do not
contain bleach should be used.
Liquid detergents
suitable for colors
and dark colors can
be used at dosages
recommended for
lightly soiled clothes.
Prefer liquid
detergents
produced for
delicate clothes.
Woolen and silk
clothes must
be washed with
special woolen
detergents.
Allergy UK is the operational name of The British Allergy Foundation. The Seal
of Approval endorsement, which indicates that the product bearing it specifically
restricts / reduces / removes allergens from the environment of the allergy sufferer
or has significantly reduced allergen content, was created in order to provide
guidance for people seeking advice in this issue. It is aimed to assure poeple that
products had been scientifically tested or reviewed with measurable results.

14 / EN
Washng Machne / User’s Manual
4.3 Operating the product
4.3.1 Control panel
1 - Programme Selection knob (Uppermost position
On / Off)
2 - Display
3 - Delayed Start button
4 - Programme Follow-up indicator
5 - Start / Pause button
6 - Auxiliary Function buttons
7 - Spin Speed Adjustment button
8 - Temperature Adjustment button
1 2 3
4
5678
4.3.2 Programme selecton
1 Determine the programme suitable for the type, quantity and soiling level of the laundry in
accordance with the "Programme and consumption table".
1 Select the desired programme with the “Programme Selection” knob.
C
Programmes are limited with the highest spin speed appropriate for that particular type of fabric.
When selecting the program you will use, always take fabric type, color, soil degree and permitted water
temperature into consideration.
Always prefer the lowest temperature value which is fit to your laundry type. Higher temperature means higher
power consumption.
4.3.3 Programmes
• Cottons
Use for your cotton laundry (such as bed sheets, duvet and pillowcase sets, towels, bathrobes,
underwear, etc.). Your laundry will be washed with vigorous washing action for a longer washing
cycle.
• Synthetcs
Use to wash your synthetic clothes (shirts, blouses, synthetic/cotton blends, etc.). It washes with a
gentle action and has a shorter washing cycle compared to the Cottons programme.
For curtains and tulle, use the Synthetic 40˚C programme with prewash and anti-creasing functions
selected. As their meshed texture causes excessive foaming, wash the veils/tulle by putting little
amount of detergent into the main wash compartment. Do not put detergent in the prewash
compartment.
• Woollens
Use to wash your woolen clothes. Select the appropriate temperature complying with the tags of
your clothes. Use appropriate detergents for woolens.
“The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of machine
washable wool products provided that the products are washed according to the instructions on the garment label
and those issued by the manufacturer of this washing machine. M1476.”
“In UK, Eire, Hong Kong and India the Woolmark trade mark is a Certification trade mark.”

15 / EN
Washng Machne / User’s Manual
• Cottons Eco
Use to wash your normally soiled, durable cotton and linen laundry. Although it washes longer than
all other programmes, it provides high energy and water savings. Actual water temperature may
be different from the stated wash temperature. When you load the machine with less laundry (e.g.
½ capacity or less), programme time may automatically get shorter. In this case, energy and water
consumption will decrease more, providing a more economic wash. This programme is available in the
models with the remaining time indicator.
• Gentle Care 20°
Use it to wash your delicate laundry. It washes with a gentler action without any interim spins
compared to the Synthetics program. It should be used for laundry for which sensitive wash is
recommended.
• Hand Wash 20°
Use to wash your woolen/delicate clothes that bear “not machine-washable” tags and for which
hand wash is recommended. It washes laundry with a very gentle washing action to not to damage
clothes.
• Daly Xpress
Use this programme to wash your lightly soiled cotton clothes in a short time.
• Xpress Super Short
Use to wash your lightly soiled and unstained cotton laundry in a short time.
• Dark Care
Use this programme to wash your dark colored laundry or colored laundry that you do not want
them get faded. Washing is performed with little mechanic action and at low temperatures. It is
recommended to use liquid detergent or woolen shampoo for dark coloured laundry.
• Mx 40
Use this programme to wash your cotton and synthetic clothes together without sorting them.
• Shrts
Use to wash the shirts made of cotton, synthetic and synthetic blended fabrics together.
.
• Fashoncare
You can use this program to wash your laundry that bear viscous and viscous blends labels or
which are advised to be washed with delicate programs. It cleans your laundry without causing any
deformation to them. E.g.: Blouse, dress, skirt, etc.
• Sports
Use this programme to wash your garments that are worn for a short time such as sportswear. It is
suitable to wash little amount of cotton / synthetic blended garments.
• Rnse
Use when you want to rinse or starch separately.
• Spn+Dran
Use to drain the water in the machine.

16 / EN
Washng Machne / User’s Manual
4.3.4 Temperature selecton
Whenever a new programme is selected, the recommended temperature for the selected
programme appears on the temperature indicator.
To decrease the temperature, press the Temperature Adjustment button. Temperature will decrease
gradually.
C
If the programme has not reached the heating step, you can change the temperature without switching the
machine to Pause mode.
4.3.5 Spn speed selecton
Whenever a new programme is selected, the recommended spin speed of the selected programme is
displayed on the spin speed indicator.
To decrease the spin speed, press the Spin Speed Adjustment button. Spin speed decreases
gradually.
Then, depending on the model of the product, "Rinse Hold" and "No Spin" options appear on the
display. See "Auxiliary function selection" section for explanations of these options.
C
If the programme has not reached the spinning step, you can change the speed without switching the machine to
Pause mode.

17 / EN
Washng Machne / User’s Manual
4.3.6 Programme and consumpton table
• : Selectable.
* : Automatically selected, no canceling.
** : Energy Label programme (EN 60456)
*** : If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin
speed.
- : See the programme description for maximum load.
C
The auxiliary functions in the table may vary according to the model of your machine.
Water and power consumption may vary subject to the changes in water pressure, water hardness and temperature,
ambient temperature, type and amount of laundry, selection of auxiliary functions and spin speed, and changes in
electric voltage.
You can see the washing time of the programme you have selected on the display of the machine. It is normal that small
differences may occur between the time shown on the display and the real washing time.
“Selection patterns for auxiliary functions can be changed by the manufacturer company. New selection patterns can be
added or removed.”
“The spin speed of your machine may vary according to the programme; this spin speed cannot exceed the max. spin
speed of your machine.”
"The manufacturer reserves the right to make modifications in the programmes and auxiliary functions given in the table.
While these modifications will not change the machine performance, programme steps and durations can be changed."
EN 2Auxiliary functions
Programme
Max. Load (kg) Water Consumption (l) Energy Consumption (kWh) Max. Speed*** Prewash Quick Wash Rinse Hold Pet hair removal
Temperature
Cottons Eco 60** 6 45 0.94 1600 • 40-60
Cottons
90 6 66 2.25 1600 • • • • Cold-90
60 6 66 1.45 1600 • • • • Cold-90
40 6 66 0.85 1600 • • • • Cold-90
Synthetics 60 2.5 45 0.90 800 • • • • Cold-60
40 2.5 45 0.42 800 • • • • Cold-60
Daily Xpress
90 6 55 1.90 1400 • Cold-90
60 6 55 1.00 1400 • Cold-90
30 6 55 0.20 1400 • Cold-90
Xpress Super Short 30 2 40 0.11 1400 • Cold-30
Sports 40 3 48 0.45 800 • • • Cold-40
Hand Wash 20° 20 1 30 0.15 600 20
Woollens 40 1.5 40 0.30 600 • Cold-40
Dark Care 40 2.5 58 0.45 800 • Cold-40
Shirts 60 2.5 55 0.90 600 • • • Cold-60
Mix 40 40 3 45 0.50 800 • • • • Cold-40
Fashion Care 40 2 30 0.45 600 40
Gentle Care 20° 20 2.5 45 0.15 600 • 20

18 / EN
Washng Machne / User’s Manual
4.3.7 Auxlary functon selecton
Select the desired auxiliary functions before starting the programme.
Whenever a programme is selected, if a relevant auxiliary function is selected its related indicator
light will illuminate.
C
Indicator lights of the auxiliary functions that are not allowed to be selected with the current programme will
flash and an audio warning is given.
Furthermore, you may also select or cancel auxiliary functions that are suitable to the running
programme after the washing cycle starts. If the wash cycle has reached a point where no auxiliary
function can be selected, an audio warning will be given and the related auxiliary function's light will
flash.
C
Some functions cannot be selected together. If a second auxiliary function conflicting with the first one is
selected before starting the machine, the function selected first will be canceled and the second auxiliary
function selection will remain active. For example, if you want to select Quick Wash after you have selected the
Additional Water, Additional Water will be canceled and Quick Wash will remain active.
An auxiliary function that is not compatible with the programme cannot be selected. (See, “Programme and
consumption table")
Some programmes have auxiliary functions that must be operated simultaneously. Those functions cannot be
cancelled. The frame of the auxiliary function will not be illuminated, only inner area will be illuminated.
• Prewash
A Prewash is only worthwhile for heavily soiled laundry. Not using the Prewash will save energy,
water, detergent and time.
• Quck Wash
This function can be used in Cottons and Synthetics programmes. It decreases the washing times
and also the number of rinsing steps for lightly soiled laundry.
C
When you select this function, load your machine with half of the maximum laundry specified in the programme
table.
• Rnse Hold
If you are not going to unload your clothes immediately after the programme completes, you can
use rinse hold function to keep your laundry in the final rinsing water in order to prevent them from
getting wrinkled when there is no water in the machine. Press Start / Pause button after this process
if you want to drain the water without spinning your laundry. Programme will resume and complete
after draining the water.
If you want to spin the laundry held in water, adjust the Spin Speed and press Start / Pause button.
The programme resumes. Water is drained, laundry is spun and the programme is completed.
• Pet Har Removal
This function helps to remove pet hair that remain on your garments more effectively.
When you select this function, Prewash and Extra Rinse steps are added to the normal programme.
Thus, washing is performed with more water (30%) and the pet hair is removed more effectively.
A
WARNING: Never wash your pets in the washing machine.

19 / EN
Washng Machne / User’s Manual
4.3.8 End Tme
Delayed Start
With the Delayed Start function the startup of the programme may be delayed up to 19 hours.
Delayed start time can be increased by increments of 1 hour.
C
Do not use liquid detergents when you set Delayed Start! There is the risk of staining of the clothes.
Open the loading door, place the laundry and put detergent, etc. Select the washing programme,
temperature, spin speed and, if required, the auxiliary functions. Set the desired time by pressing the
Delayed Start button. Press Start / Pause button. The delayed start time you have set is displayed.
Delayed start countdown starts. “_” symbol next to the delayed start time moves up and down on
the display.
C
Additional laundry may be loaded during the delayed start period.
At the end of the countdown, duration of the selected programme will be displayed. “_” symbol will
disappear and the selected programme will start.
Changing the Delayed Start period
If you want to change the time during countdown:
Press Delayed Start button. Time will increase by 1 hour each time you press the button. If you want
to decrease the delayed start time, press Delayed Start button repeatedly until the desired delayed
start time appears on the display.
Canceling the Delayed Start function
If you want to cancel the delayed start countdown and start the programme immediately:
Set the Delayed Start period to zero or turn the Programme Selection knob to any programme. Thus,
Delayed Start function will be canceled. The End/Cancel light flashes continuously. Then, select the
programme you want to run again. Press Start / Pause button to start the programme.
4.3.9 Startng the programme
1. Press Start / Pause button to start the programme.
2. Programme follow-up light showing the startup of the programme will turn on.
C
If no programme is started or no key is pressed within 1-10 minute during programme selection process, the
machine will switch to OFF mode. Display and all indicators are turned off.
Selected programme data will be displayed if you press On / Off button.
4.3.10 Loadng door lock
There is a locking system on the loading door of the machine that prevents opening of the door in
cases when the water level is unsuitable.
"Door Locked" LED in the panel turns on when the loading door is locked.
4.3.11 Changng the selectons after the programme has started
After the programme has started you can make the following changes.
4.3.11.1 Swtchng the machne to pause mode:
Press the Start/Pause button to switch the machine to pause mode while a programme is running.
The light indicating the Start/Pause status and programme step starts flashing on the Programme
Follow-up indicator to show that the machine has been switched to the pause mode. Also, Loading
Door light will also flash until the door is ready to be opened. When the loading door is ready to
be opened loading door light will will turn off and programme step indicator and Start / Stop LED
continue to flash.
Also, when the loading door is ready to be opened, Loading Door light will also turn off in addition to
the programme step light.

20 / EN
Washng Machne / User’s Manual
4.3.11.2 Changng the auxlary functon, speed and temperature
Depending on the step the programme has reached, you can cancel or select the auxiliary functions.
See, "Auxiliary function selection".
You can also change the speed and temperature settings. See, "Spin speed selection" and
"Temperature selection".
C
If no change is allowed, the relevant light will flash for 3 times.
4.3.11.3 Addng or takng out laundry
1. Press the Start / Pause button to switch the machine to pause mode. The programme follow-up
light of the relevant step during which the machine was switched into the pause mode will flash.
2. Wait until the Loading Door can be opened.
3. Open the Loading Door and add or take out the laundry.
5. Close the Loading Door.
6. Make changes in auxiliary functions, temperature and speed settings if necessary.
7. Press Start/Pause button to start the machine.
4.3.12 Chld Lock
Use Child Lock function to prevent children from tampering with the machine. Thus you can avoid
any changes in a running programme.
C
If the Programme Selection knob is turned when the Child Lock is active, “Con” appears on the display. The Child Lock
does not allow any change in the programmes and the selected temperature, speed and auxiliary functions.
Even if another programme is selected with the Programme Selection knob while the Child Lock is active, previously
selected programme will continue running.
4.3.12.1 To actvate the chld lock:
Press and hold 1
st
and 2
nd
Auxiliary Function buttons for 3 seconds. The lights on the 1
st
and 2
nd
Auxiliary Function buttons will flash, and “C03”, “C02”, “C01” will appear on the display respectively
while you keep the buttons pressed for 3 seconds. Then, “Con” will appear on the display indicating
that the Child Lock is activated. If you press any button or turn the Programme Selection knob
when the Child Lock is active, same phrase will appear on the display. The lights on the 1st and 2nd
auxiliary function buttons that are used to deactivate the Child Lock will blink 3 times.
4.3.12.2 To deactvate the chld lock:
Press and hold 1st and 2nd auxiliary function buttons for 3 seconds while any programme is running. The lights on the
1st and 2nd Auxiliary Function buttons will flash, and “C03”, “C02”, “C01” will appear on the display respectively while
you keep the buttons pressed for 3 seconds. Then, “COFF” will appear on the display indicating that the Child Lock is
deactivated.
C
In addition to the method above, to deactivate the Child Lock, switch the Programme Selection knob to On / Off
position when no programme is running, and select another programme.
Child Lock is not deactivated after power failures or when the machine is unplugged.
4.3.13 Cancelng the programme
To cancel the programme, turn the Programme Selection knob to select another programme.
Previous programme will be canceled. End / Cancel light will flash continuously to notify that the
programme has been canceled.
Your machine will end the programme when you turn the Programme Selection knob; however, it
does not drain the water inside. When you select and start a new programme, the newly selected
programme will start depending on the step the previous programme was canceled in. For example,
it may take in additional water or continue to wash with the water inside.