Beko WX740430S User manual

2820527477_EN/23-05-19.(20:25)
Washing Machine
User’s Manual
WX740430S
EN
Document Number=

This product was manufactured using the latest technology in environmentally friendly conditions.
Please read these instructions first before using your appliance
Dear Customer,
Thank you for choosing a Beko appliance.
Please take some time to read this user manual before using your appliance,to ensure you know how to
safely operate the controls and functions.
Carefully follow all unpacking and installation instructions to ensure the appliance is correctly connected
and fitted prior to use.
Please write your product model and serial number on the last page of this user manual,and store in a safe
location close to the appliance for easy future reference.
This user manual may also be applicable for several other models. Differences between models will be
listed.
If you have any questions or concerns,please call our contact centre or find help and information online at
www.beko.co.uk .com
Explanation of symbols used throughout this User Manual
C• Importantinformationor
usefulhintsaboutusage.
A• Warningforhazardous
situationswithregard
tolifeandproperty.
B• Warningforelectricshock.
• Recyclablematerials.
Do not dispose of the packaging materials together with domestic or other wastes.Take them to the
packaging material collection points designated by the local authorities.

3 / EN
Washing Machine / User’s Manual
1 General safety instructions
This section contains safety instructions that will help protect from risk of
personalinjury or property damage.Failure to follow these instructions shall
void any warranty.
1.1 Life and property safety
uNeverplacetheproductonacarpet-coveredfloor.Otherwise,lackofairflow
beneath the machine will cause electrical parts to overheat.This will cause
problems with your product.
uUnplug the product if it is not in use.
uAlways have the installation and repairing procedures carried out by the
Authorised Service Agent. The manufacturer shall not be held liable for
damages that may arise from procedures carried out by unauthorised
persons.
uThewatersupplyanddraininghoses must be securely fastened and remain
undamaged.Otherwise,there is the risk of water leakage.
uWhile there is still water inside the product,never open the loading door or
remove the filter. Otherwise, risk of flooding and injury from hot water will
occur.
uDo not force open the locked loading door.The door will open immediately
after the washing cycle has ended. If the door does not open, apply the
solutions provided for "Loading door cannot be opened." error in the
Troubleshooting section. In case of forcing the loading door to open, the
door and the lock mechanism may get damaged.
uUse detergents,softeners and supplements suitable for automatic washing
machines only.
uFollow the instructions on the label of textile products and the detergent
package.
1.2 Children's safety
uThisproductcanbeusedbychildrenatandabove8yearsoldandbypersons
whose physical, sensory or mental capabilities were not fully developed or
who lack experience and knowledge provided that they are supervised or
trainedon the safeusage of theproduct and the risksit brings out.Children
should not play with the product. Cleaning and maintenance works should
not be performed by children unless they are supervised by someone.
Children under the age of 3 should be kept away unless continuously
supervised.
uPackaging materials are dangerous for the children. Keep packaging
materials in a safe place away from reach of the children.

4 / EN Washing Machine / User’s Manual
uElectrical products are dangerous for the children.Keep children away from
the product when it is in use. Do not allow them to play with the product.
Use child lock to prevent children from intervening with the product.
uDo not forget to close the loading door when leaving the room where the
product is located.
uStore all detergents and additives in a safe place away from the reach of
the children by closing the cover of the detergent container or sealing the
detergent package.
1.3 Electrical safety
uIf the product has a failure,it should not be operated unless it is repaired by
theAuthorised Service Agent!There is the risk of electric shock!
uThis product is designed to resume operating in the event of powering
on after a power interruption. If you wish to cancel the programme, see
"Cancelling the programme" section.
uPlug the product into a grounded outlet protected by a 16 A fuse. Do not
neglect to have the grounding installation made by a qualified electrician.
Our company shall not be liable for any damages that will arise when the
product is used without grounding in accordance with the local regulations.
uDo not wash the product by spraying or pouring water onto it! There is the
risk of electric shock!
uNever touch the power cable plug with wet hands! Never unplug by pulling
on the cable.Always press on the plug with one hand and pull out the plug
by grabbing with the other hand.
uProduct should be unplugged during installation, maintenance, cleaning
and repair procedures.
uIf the power cable is damaged, it must be replaced by the manufacturer,
authorized service or a similarly qualified person (preferably an electrician)
or someone designated by the importer in order to avoid possible risks.
1.4 Hot surface safety
The glass of the loading door gets too hot while
washing at higher temperatures. Therefore,
especially do not allow children touch the
loading door glass while washing.

5 / EN
Washing Machine / User’s Manual
2Important instructions for environment
2.1 Compliance with WEEE Directive
This product complies with EUWEEE Directive (2012/19/EU). This product bears a classification
symbol for waste electrical and electronic equipment (WEEE).
This product has been manufactured with high quality parts and materials which can be reused
and are suitable for recycling.Do not dispose of the waste product with normal domestic and
other wastes at the end of its service life.Take it to the collection center for the recycling of
electrical and electronic equipment.Please consult your local authorities to learn about these
collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful
and prohibited materials specified in the Directive.
2.2 Package information
Packaging materials of the product are manufactured from recyclable materials in accordance with our
National Environment Regulations.Do not dispose of the packaging materials together with the domestic or
other wastes.Take them to the packaging material collection points designated by the local authorities.
3 Intended use
• Thisproducthasbeendesignedfordomesticuse.Itisnotforcommercialpurposesoritshouldnotbeused
out of its intended use.
• Theproductmustonlybeusedforwashingandrinsingoflaundrythataremarkedaccordingly.
• Themanufacturerwaivesanyresponsibilityarisenfromincorrectusageortransportation.
• Theservicelifeofyourproductis10years.Duringthisperiod,originalsparepartswillbeavailableto
operate the appliance properly.

6 / EN Washing Machine / User’s Manual
4Technical specifications
AWARNING: Consumption values are applicable for cases where the wireless network connection is off.
Height (cm) 84
Width (cm) 60
Depth (cm) 55
Net weight (±4 kg.) 67
SingleWater inlet / DoubleWater inlet •/-
•Available
Electrical input (V/Hz) 230V / 50Hz
Total current (A) 10
Total power (W) 2200
Main model code 1310
Complying Commission Delegated Regulation (EU) No 1061/2010
Supplier name or trademark Beko
Model name WX740430S
7145842600
Rated capacity (kg) 7
Energy efficiency class / Scale from A+++ (Highest Efficiency) to D (Lowest Efficiency) A+++
Annual Energy Consumption (kWh) (1) 156
Energy consumption of the standard 60°C cotton programme at full load (kWh) 0,730
Energy consumption of the standard 60°C cotton programme at partial load (kWh) 0,665
Energy consumption of the standard 40°C cotton programme at partial load (kWh) 0,660
Power consumption in‘off-mode’ (W) 0,500
Power consumption in‘left-on mode’ (W) 0,500
AnnualWater Consumption (l) (2) 9899
Spin-drying efficiency class / Scale from A (Highest Efficiency) to G (Lowest Efficiency) B
Maximum spin speed (rpm) 1400
Remaining moisture Content (%) 53
Standard cotton programme(3) Cotton Eco 60°C and 40°C
Programme time of the standard 60°C cotton programme at full load (min) 275
Programme time of the standard 60°C cotton programme at partial load (min) 225
Programme time of the standard 40°C cotton programme at partial load (min) 225
Duration of the left-on mode (min) N/A
Airborne acoustical noise emissions washing/spinning (dB) 52/73
Built-in No
(1) Energy Consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load, and the
consumption of the low-power modes.Actual energy consumption will depend on how the appliance is used.
(2) Water consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load.Actual water
consumption will depend on how the appliance is used.
(3) “Standard 60°C cotton programme” and the“standard 40°C cotton programme” are the standard washing programmes to which the information
in the label and the fiche relates and these programmes are suitable to clean normally soiled cotton laundry and that they are the most efficient
programmes in terms of combined energy and water consumption.

7 / EN
Washing Machine / User’s Manual
4.1 Installation
• Preparationofthelocationandelectrical,tapwaterandwastewaterinstallationsattheplaceofinstallation
is the customer's responsibility.
• Makesurethatthewaterinletanddischargehosesaswellasthepowercablearenotfolded,pinchedor
crushed while pushing the product into its place after installation or cleaning procedures.
• Themanufacturershallnotbeheldliablefordamagesthatmayarisefromprocedurescarriedoutby
unauthorised persons.
• Priortoinstallation,visuallycheckiftheproducthasanydefectsonit.Ifso,donothaveitinstalled.
Damaged products cause risks for your safety.
4.1.1 Appropriate installation location
• Placetheproductonahardandlevelfloor.Donotputitontoacarpetwithhighpileorothersimilar
surfaces.
• Ifthewashingmachineanddryerareplacedontopofeachother,theirtotalweight–whenloaded–
amounts to 180 kilograms.Place the products on a solid and flat floor that has sufficient load carrying
capacity!
• Donotplacetheproductonthepowercable.
• Donotinstalltheproductinenvironmentswherethetemperaturefallsbelow0ºC.
• Leavingagapatthesidesofthemachineissuggestedtoreducevibrationandnoise
• Onaraisedfloor,donotplacetheproductnexttotheedgeoronaplatform.
• DonotplaceheatsourcessuchasHobs,Irons,Ovens,etc.onthewashingmachineanddonotusethem
on the product.
4.1.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging reinforcement.
Remove the packaging reinforcement that is attached to the ribbon. Do
not attempt this operation alone,get help.
4.1.3 Removing the transportation locks
1 Loose all bolts with an appropriate wrench until they turn freely.
2 Remove the transport safety bolts by rocking them slightly.
3 Insert the plastic covers from the bag containing the user manual into the openings on the rear panel.
ACAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise,the product will be
damaged.
CKeep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the
future.
Install the transport safety bolts in the reverse order of the disassembly procedure.
Never move the product without the transportation safety bolts properly fixed in place!

8 / EN Washing Machine / User’s Manual
4.1.4 Connecting the water supply
CThewatersupplypressurerequiredtoruntheproductisbetween1to10bars(0.1–1MPa).Itisnecessarytohave
10–80litresofwaterflowingfromthefullyopentapinoneminutetohaveyourmachinerunsmoothly.Attachapressure
reducing valve if the water pressure is higher.
ACAUTION: Models with a single water inlet should not be connected to the hot water tap.In such a case the laundry will
get damaged or the product will switch to protection mode and will not operate.
CAUTION: Do not use old or used water inlet hoses on the new product.It may cause stains on your laundry.
1 Tighten the nuts of the hose by hand.Never use a tool when tightening the nuts.
2 When hose connection is completed,check whether there are no leak problems at the connection
points by opening the taps fully. If any leaks occur, turn off the tap and remove the nut.Retighten the nut
carefully after checking the seal.In order to prevent the water leaks and resultant damages,keep the
taps closed when you do not use the product.
4.1.5 Connecting the drain hose to the drain
• Attachtheendofthedrainhosedirectlytothewastewaterdrain,lavatoryorbathtub.
ACAUTION: Your drain house will be flooded if the hose comes out of its housing during water discharge. Moreover,there
is risk of scalding due to high washing temperatures! In order to prevent such situations and make sure that the machine
performs water intake and discharge processes without any problem, fix the drain hose securely.
• Connectthedrainhosetoaminimumheightof40cmandamaximumheightof100cm.
• Incasethedrainhoseiselevatedafterlayingitonthefloorlevelorclosetotheground(lessthan40cm
above the ground),water discharge becomes more difficult and the laundry may come out excessively wet.
Therefore,follow the heights described in the figure.
40 cm
100 cm
• Topreventthewastewatergoingbackintothemachineagainandtoensureeasydrainage,donot
immerse the end of the hose into the waste water or do not insert it into the drain for more than 15 cm.If it
is too long,cut it short.
• Theendofthehoseshouldnotbebent,itshouldnotbesteppedonandthehosemustnotbepinched
between the drain and the machine.
• Ifthelengthofthehoseistooshort,addanoriginalextensionhose.Lengthofthehosemaynotbelonger
than 3.2 m.To avoid water leak failures, the connection between the extension hose and the drain hose of
the product must be fitted well with an appropriate clamp as not to come off and/or leak.

9 / EN
Washing Machine / User’s Manual
4.1.6 Adjusting the feet
ACAUTION: In order to ensure that the product operates more silently and vibration-free,it must stand level and balanced
on its feet.Balance the machine by adjusting the feet.Otherwise, the product may move from its place and cause crushing
and vibration problems.
CAUTION: Do not use any tools to loosen the lock nuts. Otherwise,they will get damaged.
1 Loosen the lock nuts on the feet by hand.
2 Adjust the feet until the product stands in a stable and balanced way.
3. Tighten all lock nuts by hand again.
4.1.7 Electrical connection
Connect the product to a grounded outlet protected by a 13A fuse.Our company shall not be liable for any
damages that will arise when the product is used without grounding in accordance with the local regulations.
• Connectionmustcomplywithnationalregulations.
• Thewiringfortheelectricaloutletcircuitmustbesufficienttomeettheappliancerequirements.Useofa
Groud Fault Circuit Interrupter (GFCI) is recommended.
• Powercableplugmustbewithineasyreachafterinstallation.
• Ifthecurrentvalueofthefuseorbreakerinthehouseislessthan13Amps,haveaqualifiedelectrician
install a 13Amp fuse.
• Thevoltagespecifiedinthe“Technicalspecifications”sectionmustbeequaltoyourmainsvoltage.
• Donotmakeconnectionsviaextensioncablesormulti-plugs.
BWARNING: Damaged power cables must be replaced byAuthorised Service Agents.
Electrical requirements
Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the
rating label corresponds to your electricity supply.
We recommend that this appliance be connected to the mains supply via a suitable switched and fused socket
in a readily accessible position.
Should the mains lead of the appliance become damaged or need replacing at any time, it must be replaced
by a special purpose made mains lead which can only be obtained from anAuthorised Service Agent.
BWARNING: This appliance must be earthed
If the fitted moulded plug is not suitable for your socket,then the plug should be cut off and an appropriate
plug fitted.
Destroy the old plug,a cut off plug with a bare cord could cause a shock hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this appliance incorporates a 13A fuse.Should the fuse need to be replaced anASTA
approved BS1362 fuse of the same rating must be used.Do not forget to refit the fuse cover. In the event of
losing the fuse cover, the plug must not be used until a replacement fuse cover has been fitted.Colour of the
replacement fuse cover must be the same colour as that visible on the pin face of the plug.Fuse covers are
available from any good electrical store.

10 / EN Washing Machine / User’s Manual
Important
Fitting a different plug
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals on your
plug,proceed as follows:
1 Connect the green - yellow or green (earth) wire to the terminal in
the plug marked‘E’ or with the symbol or coloured green and
yellow or green.
2 Connect the blue (neutral) wire to the terminal in the plug marked
‘N’ or coloured black.
3 Connect the brown (live) wire to the terminal in the plug marked‘L’
or coloured red.
With the alternative plugs a 13A fuse must be fitted either in the plug or
adaptor or in the main fuse box.If in doubt contact a qualified electrician.
Transportation of the product
1. Unplug the product before transporting it.
2. Remove water drain and water supply connections.
3. Drain all water that has remained in the product.
4. Install transportation safety bolts in the reverse order of removal procedure.
CNever move the product without the transportation safety bolts properly fixed in place!
AWARNING: Packaging materials are dangerous to children.Keep packaging materials in a safe place away from reach
of the children.
4.1.8 Initial use
Before starting to use the product make sure that the preparations are
made which are in line with the“Important Safety and Environment
Instructions”and the instructions in the “Installation”section.
To prepare the product for washing laundry,first perform a Drum
Cleaning programme.If this is not available in your machine,apply the
method which is described in the section 4.4.2.
CUse an anti-limescale suitable for the washing machines.
Some water might have remained in the product due to the quality control processes in production. It is not harmful for the
product.