Beko WMB 60801 Y+ User manual

2820523933_EN / 18-03-14.(11:33)
Document Number
WMB 60801 Y+
Washing Machine
User’s Manual
Makinë larëse
Udhëzim për përdorim
Mašina za pranje veša
Uputstvo za upotrebu
Mašina za pranje rublja
Priručnik za korisnika

Упатство за употреба

2/ EN Washing Machine / User’s Manual
1 Important instructions for safety and environment
This section contains safety instructions that will help protect from risk of perso-
nal injury or property damage. Failure to follow these instructions shall void any
warranty.
1.1 General safety
• This product can be used by children at and above 8 years old and by persons
whose physical, sensory or mental capabilities were not fully developed or who
lack experience and knowledge provided that they are supervised or trained on
the safe usage of the product and the risks it brings out. Children must not play
with the product. Cleaning and maintenance works should not be performed by
children unless they are supervised by someone.
• Never place the product on a carpet-covered floor. Otherwise, lack of airflow
beneath the machine will cause electrical parts to overheat. This will cause pro-
blems with your product.
• If the product has a failure, it should not be operated unless it is repaired by the
Authorized Service Agent. There is the risk of electric shock!
• This product is designed to resume operating in the event of powering on after
a power interruption. If you wish to cancel the programme, see "Cancelling the
programme" section.
• Connect the product to a grounded outlet protected by a 16 A fuse. Do not ne-
glect to have the grounding installation made by a qualified electrician. Our com-
pany shall not be liable for any damages that will arise when the product is used
without grounding in accordance with the local regulations.
• The water supply and draining hoses must be securely fastened and remain un-
damaged. Otherwise, there is the risk of water leakage.
• Never open the loading door or remove the filter while there is still water in the
drum. Otherwise, risk of flooding and injury from hot water will occur.
• Do not force open the locked loading door. The loading door will be ready to open
just a few minutes after the washing cycle comes to an end. In case of forcing
the loading door to open, the door and the lock mechanism may get damaged.
• Unplug the product when not in use.
• Never wash the product by spreading or pouring water onto it! There is the risk of
electric shock!
• Never touch the plug with wet hands! Never unplug by pulling on the cable,
always pull out by grabbing the plug.
• Use detergents, softeners and supplements suitable for automatic washing ma-
chines only.
• Follow the instructions on the textile tags and on the detergent package.
• The product must be unplugged during installation, maintenance, cleaning and
repairing procedures.
• Always have the installation and repairing procedures carried out by the
Authorized Service Agent. Manufacturer shall not be held liable for damages that
may arise from procedures carried out by unauthorized persons.
• If the power cable is damaged, it must be replaced by the manufacturer, after
sales service or a similarly qualified person (preferably an electrician) or someone

3/ EN Washing Machine / User’s Manual
designated by the importer in order to avoid possible risks.
• Place the product on a rigid, flat and level surface.
• Do not place it on a long-pile rug or similar surfaces.
• Do not place the product on a high platform or near the edge on a cascaded sur-
face.
• Do not place the product on the power cable.
• Never use sponge or scrub materials. These will damage the painted, chrome
plated and plastic surfaces.
1.2 Intended use
• This product has been designed for domestic use. It is not suitable for commer-
cial use and it must not be used out of its intended use.
• The product must only be used for washing and rinsing of laundry that are mar-
ked accordingly.
• The manufacturer waives any responsibility arisen from incorrect usage or trans-
portation.
1.3 Children's safety
• Packaging materials are dangerous to children. Keep packaging materials in a
safe place away from reach of the children.
• Electrical products are dangerous for the children. Keep children away from the
product when it is in use. Do not let them to tamper with the product. Use child
lock to prevent children from intervening with the product.
• Do not forget to close the loading door when leaving the room where the product
is located.
• Store all detergents and additives in a safe place away from the reach of the
children by closing the cover of the detergent container or sealing the detergent
package.
While washing the laundry at high temperatures, the loading
door glass becomes hot. Therefore, keep especially the children
away from the loading door of the machine while the washing
operation is in progress.
1.4 Package information
• Packaging materials of the product are manufactured from recyclable materials
in accordance with our National Environment Regulations. Do not dispose of the
packaging materials together with the domestic or other wastes. Take them to the
packaging material collection points designated by the local authorities.
1.5 Disposing of the waste product
• This product has been manufactured with high quality parts and materials which
can be reused and are suitable for recycling. Therefore, do not dispose the pro-
duct with normal domestic waste at the end of its service life. Take it to a collec-
tion point for the recycling of electrical and electronic equipment. Please consult
your local authorities to learn the nearest collection point. Help protect the envi-
ronment and natural resources by recycling used products. For children's safety,
cut the power cable and break the locking mechanism of the loading door so that
it will be non-functional before disposing of the product.

4/ EN Washing Machine / User’s Manual
1.6 Compliance with WEEE Directive
This product complies with EU WEEE Directive (2012/19/EU). This pro-
duct bears a classification symbol for waste electrical and electronic
equipment (WEEE).
This product has been manufactured with high quality parts and mate-
rials which can be reused and are suitable for recycling. Do not dispose
of the waste product with normal domestic and other wastes at the
end of its service life. Take it to the collection center for the recycling of
electrical and electronic equipment. Please consult your local authori-
ties to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU).
It does not contain harmful and prohibited materials specified in the Directive.
2 Installation
Refer to the nearest Authorised Service Agent for installation
of the product. To make the product ready for use, review
the information in the user manual and make sure that the
electricity, tap water supply and water drainage systems are
appropriate before calling the Authorized Service Agent. If they
are not, call a qualified technician and plumber to have any
necessary arrangements carried out.
CINFORMATIONS
Preparation of the location and electrical, tap water and waste
water installations at the place of installation is under customer’s
responsibility.
Make sure that the water inlet and discharge hoses as well as the
power cable are not folded, pinched or crushed while pushing the
product into its place after installation or cleaning procedures.
BWARNING
Installation and electrical connections of the product must be
carried out by the Authorized Service Agent. Manufacturer shall not
be held liable for damages that may arise from procedures carried
out by unauthorized persons.
AWARNING
Prior to installation, visually check if the product has any defects on
it. If so, do not have it installed. Damaged products cause risks for
your safety.
2.1 Appropriate installation location
• Place the machine on a rigid floor. Do not place it on a long
pile rug or similar surfaces.
• Total weight of the washing machine and the dryer -with
full load- when they are placed on top of each other
reaches to approx. 180 kilograms. Place the product on a
solid and flat floor that has sufficient load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product at places where temperature may
fall below 0ºC.
• Place the product at least 1 cm away from the edges of
other furniture.
2.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by
pulling the ribbon.
2.3 Removing the transportation locks
AWARNING
Do not remove the transportation locks before taking out the
packaging reinforcement.
Remove the transportation safety bolts before operating the
washing machine! Otherwise, the product will be damaged.
Loosen all the bolts with a suitable spanner until they rotate
freely (C). Remove transportation safety bolts by turning them
gently.Attach the plastic covers supplied in the User Manual
bag into the holes on the rear panel. (P)
CINFORMATIONS
Keep the transportation safety bolts in a safe place to reuse when
the washing machine needs to be moved again in the future.
Never move the product without the transportation safety bolts
properly fixed in place!

5/ EN Washing Machine / User’s Manual
2.4 Connecting water supply
CINFORMATIONS
The water supply pressure required to run the product is between
1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters
of water flowing from the fully open tap in one minute to have your
machine run smoothly.Attach a pressure reducing valve if water
pressure is higher.
If you are going to use the double water-inlet product as a single
(cold) water-inlet unit, you must install the supplied stopper to
the hot water valve before operating the product. (Applies for the
products supplied with a blind stopper group.)
If you want to use both water inlets of the product, connect the
hot water hose after removing the stopper and gasket group from
the hot water valve. (Applies for the products supplied with a blind
stopper group.)
AWARNING
Models with a single water inlet should not be connected to the
hot water tap. In such a case the laundry will get damaged or the
product will switch to protection mode and will not operate.
Do not use old or used water inlet hoses on the new product. It may
cause stains on your laundry.
Connect the special hoses supplied with the product to the
water inlets on the product. Red hose (left) (max. 90 ºC) is for
hot water inlet, blue hose (right) (max. 25 ºC) is for cold water
inlet.
AWARNING
Ensure that the cold and hot water connections are made correctly
when installing the product. Otherwise, your laundry will come out
hot at the end of the washing process and wear out.
Tighten all hose nuts by hand. Never use a wrench when
tightening the nuts. Open the taps completely after making the
hose connection to check for water leaks at the connection
points. If any leaks occur, turn off the tap and remove the nut.
Retighten the nut carefully after checking the seal. To prevent
water leakages and damages caused by them, keep the taps
closed when the machine is not in use.
2.5 Connecting to the drain
• The end of the drain hose must be directly connected to
the wastewater drain or to the washbasin.
AWARNING
Do not remove the transportation locks before taking out the
packaging reinforcement.
• The hose should be attached to a height of at least 40 cm,
and 100 cm at most.
• In case the hose is elevated after laying it on the floor level
or close to the ground (less than 40 cm above the ground),
water discharge becomes more difficult and the laundry
may come out excessively wet. Therefore, follow the
heights described in the figure.
100cm
40cm
• To prevent flowing of dirty water back into the machine and
to allow for easy discharge, do not immerse the hose end
into the dirty water or do not drive it in the drain more than
15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not be
stepped on and the hose must not be pinched between the
drain and the machine.
• If the length of the hose is too short, use it by adding
an original extension hose. Length of the hose may not
be longer than 3.2 m. To avoid water leak failures, the
connection between the extension hose and the drain
hose of the product must be fitted well with an appropriate
clamp as not to come off and leak.
2.6 Adjusting the feet
AWARNING
In order to ensure that the product operates more silently and
vibration-free, it must stand level and balanced on its feet. Balance
the machine by adjusting the feet. Otherwise, the product may
move from its place and cause crushing and vibration problems.
Loosen the lock nuts on the feet by hand. Adjust the feet until
the product stands level and balanced. Tighten all lock nuts
again by hand.
AWARNING
Do not use any tools to loosen the lock nuts. Otherwise, they will
get damaged.
2.7 Electrical connection
Connect the product to a grounded outlet protected by a fuse
complying with the values in the "Technical specifications"
table. Our company shall not be liable for any damages that
will arise when the product is used without grounding in
accordance with the local regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after
installation.
• The voltage and allowed fuse or breaker protection are
specified in the “Technical specifications” section. If the
current value of the fuse or breaker in the house is less
than 16 Amps, have a qualified electrician install a 16 Amp
fuse.
• The specified voltage must be equal to your mains voltage.
• Do not make connections via extension cables or multi-
plugs.