Bellagio Luxury MT-NR1401 User manual

MT-NR1401
Massage Bathtub
Instructions of Installation and Use

Thread sealing tape
Tape measure
Accessory box 2:
Shower head 1pcs
Drain cover 1pcs
Please make sure all accessories are in the package
(Bathtub 1set Accessory box 2pcs Pillow 2pcs)
Accessory box 1:
Faucet 1 pcs
Open spanner
Gradient
Installation Tools(no included)
Pillow
Adjustable spanner
Contents
Page2
Page4
Preparations
02
01
WARNING
1. For a person who has heart trouble, high blood pressure & sugar diabetes should
not take a steam shower or bath when feeling sick. (The kid is suggested to be
accompanied by an adult when taking a bath)
,
2. Don t take a bath alone after drinking wine with alcohol or excess sports.
3. The water temeperature should be below 45℃ during shower and the
recommended temperature is 30℃-38℃.
,
4. Don t take a bath for a long time. Recommended time: 15-21 .
5. All the information in this instruction are subject to change without prior notice.
6. Settings, configurations and details of the products are subject to be changed
or upgraded without prior notice.
7. For the maintenance, please contact the technicians appointed by the dealer
,
and don t disassemble and fix by yourself, or the supplier will be free from any
conquences that may occur.
8. Don't run the water pump until the water level in the bathtub goes beyond the
highest jet.
minutes
Dear Customer,
Thank you for choosing our product. For your safe concern, please take a few
minutes to read this manual before installation and use.

MODEL: MT-NR1401
SIZE: 1380mmX1380mmX580mm
580mm
1380mm
1380mm
840mm
500mm 500mm
Drain hole
Cold
Hot
Install 2 water supply holes (one for cold
and another for hot), 1 electrical outlet, 1
drain hole (diameter≥5cm) in advance.
Do as the pic. shows:
840mm
1Control Panel
2Waterfall
3
Water Circulation
4Cold Water Handle
5Switch Handle
6Hot Water Handle
7 Shower Head
8Small Jets
9Pillow
Volume Control
Big Water Jets
Light
Air Jets
11
12
13
14
10
15 Drainer Switch
Drainer
04
03
Installation rocess P
Preparations
1. Open the accessory box 1 as pic.
Shows.
2. Remove the screw of inlet faucet.
3. Put the inlet faucet into the
hole of the bathtub.
4. Put the rubber from below, and
use spanner to screw it.
5. Distinguish the water pipes of faucet. 6. Use spanner to screw the tie in.

1. Open the accessory box 2 as pic.
shows
2. Put the shower head into the bathtub
in right position as pic. shows
3. Distinguish water inlet pipe 4. Screw it
5. Side up the bathtub, then install
downcomer
6. Use thread sealing tape to wrap
around the drain hole
7. Make the thread sealing tape smooth 8. Fasten the drain tube
9. Put downcomer into the drain hole on
the ground
11. Put plugs into the drain hole
10. Drain sewage of the tube, then
connect the cold and hot water
pipe separately
1 2. Install pillow
06
05
Installation Process Installation rocess P

1. The creepage protector will
automatically cut off the circuit if the
current is too high.
2. Volume control
Unique Point
13. Seal the barthtub edge by silicon glue as follows
3. Waste water free piping system
08
07
Installation Process Installation rocess P

Precautions
1.
should be installed in the place easily to be controlled.
2. The electronic parts should be well grounded, otherwise, the manufacturer will not be
liable for any loss or consequences occurred.
3. The load capability of the power supply should be considered during installation, or it
affects the normal operation of the product or may lead to accident!
4. For any functions can not be activated through the ways mentioned above, please
contact a certified technicians or local dealer.
5. If you don't use the product for a long time, please disconnect the main power supply.
6. Parts containing live parts, except parts supplied with safety extra-low voltage not
exceeding 12V, must be inaccessible to a person in the bath.
7. Earthed appliances must be permanently connected to fixed wiring.
8. Parts incorporating electrical components, except remote control devices, must be
located or fixed so that they cannot fall into the bath.
9. The appliance should be supplied through a residual current device (RCD) having a
rated residual operating current not exceeding 30mA.
10. Make sure that the wire is laid correctly.
11. Make sure that the equipotential connection is done correctly.
12. The means having a contact at least 3.0mm separation in all poles that provide full
disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
13. If the supply cord is damaged,it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
The installation should be carried out by a qualified technician and creepage protector
Earthing Marking Equipotential Switch Marking
10
09
1. During the transportation or installation, do not pull the pipe or hold to avoid
the water leakage. ,
2. After long time use, if there are some dirt on product s surface, wipe it off gently by a soft
towel stained with mild detergent; for the metal parts, polish it with some car wax by a
towel, which brings out a refreshing appearance.
3. Scale deposit can be wiped off with warm citric acid or vinegar by a soft cloth.
,
4. Don t clean the tub and with hard or coarse material to avoid any scratches.
,
5. Don t clean the tub and with gasoline to avoid any damages.
6. It is not recommended to leave water in the tub for a long time or use this tub for washing
purpose. Pls drain off the water after the bath and disconnect the power supply.
7. There should be sufficient power supply and wires should be safely grounded.
8. For your safty, a professional technician is necessary to ensure earthing wire be well
grounded and a RCCB fitted during installation.
accessories
accessories
accessories
Cleaning & Maintaining
Installation Process Installation rocess P