Bellagio Luxury MT-NR1420 Guide

Massage Bathtub
Instructions of Installation
MODEL: MT-NR1420
SIZE: 1400*1400*600mm

Preparations
01
02
Please use tools to open the packing;
Make sure all accessories are in the packing
Pillows: 2pcs
Accessory Box:
Drain 1pc Handheld shower
hose 1pc
Handheld shower 1pc Drain cover 1pc
Installation Tools:(no included)
A: Gradient B: Sealant C: Adjustable spanner D: PTFE tape
Dear Customer,
Thank you for choosing our product. For your safe concern, please take a few
minutes to read this manual before installation and use.
WARNING
1、Children and adolescent are only allowed to use the bathtub in accompany
with an adult.
2、
People with hypertension, diabetes or cardiovascular diseases are not allowed
to use the bathtub.
3、
Don’t hit or rub the bathtub with a hard object to avoid damage and scratches.
4、To avoid stumbling, please pay attention to the drop height when go in or out
of the appliance.
5、Watch out the appliance with suds to avoid slip.
6、Don’t use acidic and strong alkaline detergent, acetone, ammonia and so on.
Clean with alkalescent detergent and soft cloth.
7
、
If the sealant falls off from the glass, please glue it immediately to avoid the
leakage.
8、Specifications can be varied without notice.
.
.

Preparations
Preparations
03
04
Bathtub Configuration Installation of Electric Appliance
1. Electric Parameter
Rated Voltage
Rated Frequency
Max Rated Power
Rated Current
220V
50Hz
2950W
13.4A
2.All electrical connections should be made by a licensed, locally certified electrician,
In accordance with the requirements of the requirements of the national electrical
codes and procedures.
3.There should be electric-leakage protector on the power supply. Power lines must be fixed
ones, which are with good ground line. The section of the electrical wire should not be less
than 2.5 m². The power supply appliance should be in accordance with the National Safety
Standard. And connect the protective ground line on the ground line- mark of bathtub frame
(The electric-leakage protector is prepared and connected by user).
4.Warning: when using electrical products, basic precautions should always be followed,
including the following.
5.Danger: risk of electric shock! connect only to circuits protected by a Ground Fault Circuit
Interrupter (GFCI). A GFCI is not supplied, however, we do specify its use. all known code
authorities require a GFCI.
Installation of Water Supply
Item
Description
Item
Description
1
Small jet
2
Big jet
3
Faucet
4
Suction
5
Hand shower
6
On/off swith
7
Underwater light
8
Drainer
9
Regulator

Preparations
I ns t alla t ion Process
05
06
Cold ater
Hot ater
Switch alve
1. Hose Connecting Way
The fittings of bathtub were already connected before shipment except faucet.
Users need to install the faucet according to the back procedures, and then connect
the cold/hot water hose to the corresponding water supply tube, which should be in
the shelter of the bathtub’s back.
Installation of Bathtub
1. As the picture shows below, turn over the bathtub, wrap the drainer hole with thread
PTFE tape, and then screw the drainer.
A: Handheld Shower
B: Switch of Handheld Shower and Faucet
C: Hot Water Inlet
D: Cold Water Inlet
A
B
C
D
Hot water Cold water
Water Inlet Faucet Connecting
2. Water Supply Chart
Handheld shower

Installation Process
Installation Process
07
08
2. As the picture shows below, turn back the bathtub. Install the waterfall, pillow and
hand shower, and connect to the water hose. Move the bathtub to the wall corner;
put the drainer into sewer and seal the drainer. Adjust the tub feet to make the
bathtub horizontal.
3. Seal the gap between the bathtub and the wall with sealant to avoid water leakage.

Instruction of Using Our Products
Instruction of Using Our Products
09
10
Usage
1. Switch on the power supply
2. Turn on the cold/hot water switch, and adjust to the suitable temperature. Use theswitch
to choose the faucet or handheld shower to let water in.
3. Don't press the water pump switch unless the water level in the bathtub reach to or
higher than the jets position.
4. Use air regulator to adjust the massage power.
5. Rotate the handheld shower to adjust the massage effection.
6. Light turns on and changes automatically when you turn on the pump, and turns off when
you turn off the pump.
7. Press pneumatic switch, turn off the pumps, and drain the water after use. Then turn off
the power supply.
Troubleshooting
Cleaning & Maintenance
1. Use general liquid detergent and soft cloth for daily cleaning. Don't use detergent that
with acetone or ammonia. Disinfector with formic acid and formaldehyde is forbidden
during disinfection.
2. If there is scratch on the bathtub surface, use 2000# waterproof abrasive paper to
polish it and lay toothpaste on. Then use soft cloth to furbish it.
3. Scale deposit can be wiped off with warm citric acid or vinegar by a soft cloth.
4. Screw off the Water Circulation and jets for cleaning when plug up by litter, such as hair
5. Frequent cleaning is not necessary for the parts gilded and silver-gilt
6. Don't clean the tub with hard or coarse material to avoid any scratches; and don'tclean
the tub by detergent with chemical menstruum to avoid any damages.
7. Be sure to drain off the water and disconnect the power supply after use
8. Don't hit and score the bathtub by hard or keen-edged material. And don't touch the
bathtub by cigarette end or heat source that over 70℃
9. Water massage system cleaning: fill the bathtub with 40℃hot water, and add
detergent (2g/L). Then run the water massage system for 5 minutes. After that, stop
the pump and drain the water. Fill the bathtub with cold water, and run the water
massage system for 3 minutes. Clean the bathtub after stopping the pump and
draining offthe water.
Precautions
1. The installation should be carried out by a qualified technician, and should be according
to the manual.
2. The appliance electric parameter should be tally with the National Safety Standard. And
there should be creepage protector on the power supply. Make sure the ground wire is
safe. Don't touch the switch, electrical outlet and plug with water.
3. Don't use overheated water. Put cold water first, then hot water. Don't run the appliance
until the water level is higher than the jets.
4. The rated voltage of this appliance is 220V. Don't run it when the voltage is over 235V
or under 190V.
5. Disconnect the power supply after use
6. Don't take a bath for a long time. Recommended time: less than 30 minutes
7. Please restart the appliance for occasional system halt
8. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
9. This manual is attached with the product. Before installation, please read it carefully.All
the installation and use should conform to this manual, to avoid damage or other accident.
Caution:
1. When the bathtub can't work, please check according to the troubleshooting list. If you can’t judge
the reason or unable to repair
it, please contact us.
2. T o insure the customers' safety , the installation should be carried out by a qualified technician.
Please use eligible creepage protector
. The ground wire should be well connected to the ground.
T rouble
Possible Reason
T ry this to solve
W ater pump
Don't work.
Power supply is not well connected,
the leakage protector disconnect.
T urn on the power supply , and connect
the leakage protector.
W ater pump impeller was stuck
by sundries.
Clean the water pump impeller .
The water pump switch is of f.
Press the water pump switch.
Power supply plug don't insert or no
enough power supply .
Plug the power supply in.
W ater pump trouble.
Repair or replace the water pump.
Massage power
can't be adjusted.
V oltage problem.
.
Check voltage.
Adjust switch is of f or has problem.
Check, replace the switch.
W ater Circulation is blocked.
Clean the water circulation.
Bathtub don't
stand horizontally .
Adjustable foot is not well-adjusted.
Adjust the Adjustable foot.
W ater leakage.
Obturating ring is not good.
Replace the obturating ring.
Nut is loose.
Screw down the nut.
Connect part is not well connected.
Pay attention to the connect part
conglutination