Bellini BCS604X-1 User manual

1
Installation and User manual
Content
Safety instructions----------------------------------- 2
Features of your product--------------------------- 4
Installing the appliance------------------------------ 5
Start using your appliance---------------------------7
Maintenance -------------------------------------------9
Warranty------------------------------------------------ 10
20121211 issue 4
60cm Built-in Electrical
Cooktop
BCS604X-1
BCS604X-1F
For warranty service call 1300 373 199(Australia)
or 0508 123108(New Zealand) to connect you to
the nearest authorised service centre

2
Safety instructions
This manual explains the proper installation and use of your appliance, please read it
carefully before using even if you are familiar with the product. The manual should be kept
in a safe place for future reference. In case of failure, only theAuthorized Technical
Service may repair this hob. Otherwise the guarantee will be null and void.
Warning
General safety
zThe appliance may only be installed and connected
by trained, registered service engineers.
zBuilt-in appliances may only be used after they have
built in to suitable built-in units and work surfaces
that meet standards.
zIn the event of faults with the appliance or damage,
the appliance must be switched off and
disconnected from the electrical supply, to prevent
the possibility of an electric shock.
zRepairs to the appliance must only be carried out by
trained registered service engineers.
zThe technical and identification data for the hob
figure on the reference plate fixed to the appliance.
zThis reference plate must be consulted before
making the electrical connections.
zThe electrical connections must be made by
specialist aware to the legal and regulatory,
requirements in each country.
zIf the cable is damaged in any way it must be
replaced by the manufacturer or after sale service
or by authorized technical staff, to avoid hazard.
Correct use
zPeople (including children) who, because of their
physical, sensory or mental capabilities or their
inexperience or ignorance are not able to use the
device safely, should not use this device without
supervision or instruction by a responsible person.
zThis appliance should be used only for normal
domestic cooking and frying of food.
zThe appliance must not be used as a work surface
or as a storage surface.
zAdditions or modifications to the appliance are not
permitted.
zDo not place or store flammable liquids, highly
inflammable materials or fusible objects (e.g. plastic
film, plastic, aluminum) on or near the appliance.
zDo not heat an empty pan on the appliance.
Children’s safety
zThe cooking zones will become hot when you
cook. Therefore, always keep small children
away from the appliance.
zThe appliance is not intended for use by
young children or infirm persons without
supervision.
zYoung children should be supervised to
ensure that they do not play with the
appliance.
zTo avoid small children and pets
unintentionally switching the appliance on, we
recommend activation of the child safety
device.
Safety during use
zThere is the risk of burns from the appliance if
used carelessly.
zCables from electrical appliances must not
touch the hot surface of the appliance or hot
cookware.
zOverheated fats and oils can ignite very
quickly. Warning! Fire hazard!
zSwitch the cooking zones off after each use.
zUsers with implanted pacemakers should
keep their upper body at least 30 cm from
heating cooking zones that are switched on.
zRisk of burns! Do not place objects made of
metal, such as knives, forks, spoons and
saucepan lids on the cooking surface, as they
can get hot.

3
Safety instructions
Safety when cleaning
zFor cleaning, the appliance must be switched off
and cooled down.
zFor safety reasons, the cleaning of the appliance
with steam jet or high pressure cleaning
equipment is not permitted.
How to avoid damage to the appliance
zObjects that melt and things that boil over should
be removed straightaway.
zDo not use the cooking zones with empty
cookware or without cookware.
zTo avoid damaging cookware, do not allow
saucepans or frying pans to boil dry.
zThe ventilation gap of 5mm between the worktop
and front of the unit underneath it must not be
covered.
Disposing of the device
When disposing of the device, do not bring it to regular municipal waste containers. Instead, bring
it to electrical and electronic waste recycling and reuse center. A relevant label has been put on the
device, its instructions manual, or the package. The device has been manufactured of recyclable
material. By bringing old device to recycling collection center, you show that you care about nature.
Ask your local environmental care authority for information on location of such facilities.

4
Features Of Your Product
Hotplate Control Knobs
Technical Data
Accessories
Model Product Dimensions
(h x w x d) mm Electrical Connection Max. Power Rating Description QTY
BCS604X-1
BCS604X-1F 45x580x510 220-240V/50Hz 5500 W User Manual 1
Left-upper 1000 W Ø 155mm
ST4.2x22
4
Right-lower 1000 W Ø 155mm
Right-upper 1500 W Ø 188mm
Heating Elements
Left-lower 2000 W Ø 188mm
Installation bracket
4
Pilot Light

5
Installing The Appliance
IMPORTANT: The benchtop and surrounding cabinet(s) must be able to withstand a minimum
temperature rise of 100°C above the ambient temperature of the room it is located in, during period of
use.
This appliance is to be built into a kitchen unit (depending on size) or 600mm worktop, providing the following
minimum distances are allowed:
z600mm (minimum) between the hob surface and the underside of any horizontal surface above it.
z50mm clearance around the appliance and between the appliance surface and any combustible materials.
CAUTION: The surface temperature of the top and bottom of the appliance exceeds 95°C. To avoid a
hazard, access to the bottom of the appliance from underneath the benchtop must be restricted
IMPORTANT: There must be a gap of at least 35mm between the bottom of the appliance in situ and
any surface directly below it.
Cut a hole in the benchtop that corresponds with the dimension shown on above drawings and carefully turn
the cooktop upside down and place it on a cushioned mat and apply the sealing strip provided around the edge
of the appliance. The protective covering must be removed from both sides. Do not leave a gap in the
sealing agent or overlap the thickness.

6
IMPORTANT: Do not use a silicon sealant to seal the appliance against the benchtop. This will make
it difficult to remove the cooktop from the benchtop in future, particularly if it needs to be serviced.
IMPORTANT:
zUsing a standard screwdriver, tighten the tension clamps evenly starting at the centre and moving
diagonally, until the cooktop rim is tight on the worktop.
zDo not over fasten screws to avoid thread stripped.
zDo not use an electric or pneumatic screw driver without an adjustable safety clutch.
Electrical Connection
zThis appliance must be installed by a qualified electrician or service agent.
zThere is no cord & plug supplied with this appliance as it is to be hardwired in.
zIt is not connected via a mains socket, it is hardwired in.
zIf the mains supply where the appliance is to be installed is different from 220...240V~ make the
connection as shown in the enclosed diagrams. (The cable must be able to withstand temperatures of
120°C). Before doing this disconnect the mains supply. A good earth connection necessary and a switch
for disconnecting all the phases must be placed accessibly, with a minimum distance of 3 mm between
contacts.
Open terminal board cover at rear panel of appliance and connect as per below diagram for 220V – 240V
earthed single phase. Close the cover after complete electrical connection.
1. Benchtop
2. Screw
3. Bracket
4. Cooktop
5. Sealing

7
Start Using Your Appliance
BCS604X-1, BCS604X-1F
Before first use, switch on one hotplate at a time for 5 minutes at the maximum setting. This will help to
eliminate any new smell that exists and evaporate any humidity that has formed on the heating elements during
transit.
Control Knobs
All operations are performed by means of the 4 control knobs that are located on the right hand side of the
cooktop.
The control knobs can be turned either clockwise or anti-clockwise to select a heating level. The numbers
around the outside of each control knob indicates the power level that you have set the hotplate to.
A marking to the bottom of each control knob, indicates which hotplate it controls.
Turn the control knob of the hotplate that you wish to cook on, clockwise or anti-clockwise until it reaches the
power level that you desire.
Each hotplate can be adjusted between 1 and 6. 1being the lowest temperature setting and 6being the
highest temperature setting.
When you have finished cooking, make sure that you turn the control knob anti-clockwise to the 0 position.
Cooktop Guidelines
The first few times the cooktop is used, it may give off an acrid, burning smell. This smell will disappear
completely with repeated use.
The hotplates are fitted with cooking areas of different diameter and power. The positions where the heat will
radiate form are clearly marked on the cooktop. The saucepans must be positioned exactly on these
hotplates for efficient heating to occur. Pans should have the same diameter as the hotplate that they are
being used on.

8
You should not use saucepans with rough bottoms, as this can scratch the solid plates.
Before use, make sure that the bottoms of the saucepans are clean and dry.
Cover pans with a lid to permit cooking at a lower heat.
Food or liquid that has a high sugar content may damage the cooktop if it comes into contact with the hotplates.
Any spillages should be wiped up immediately, however, this may not prevent the hotplates from becoming
damaged.
Large pots MUST NOT be placed over two or more hotplates as damage will more than likely occur.
Do not leave pans unattended on a hotplate.
Never heat an empty pan.
Switch off the heating element before removing the pan. Once switched off, the hotplates will remain warm for
a while.
Avoid using oversized pans that may radiate excessive heat and cause damage to surrounding surfaces.
WARNING: Do not use the hotplate if the surface becomes broken or cracked.

9
Maintenance
Caution:
Before maintenance or cleaning is carried out, the range hood should be disconnected from the main power
supply. Ensure that the range hood is switched off at the wall socket and the plug removed.
Cleaning Your Cooktop
zAllow the cooktop to cool before cleaning.
zThe hotplates should be cleaned after every use to avoid build up of food.
zIf a major spillage occurs, wipe clean as soon as possible with a damp cloth.
zDo not immerse in water.
zDO NOT use spray on or other cleaners as they may cause electrical damage. DO NOT use sharp utensils
to clean.
zAbrasive cleaners or sharp objects will damage the cooktop surface. You should clean it using water and a
little washing up liquid.
zAlthough it is easier to clean some deposits whilst the hotplates are still warm, you should take care not to
burn yourself.
After Each Use
zWipe the appliance over with a damp cloth and a little washing up liquid.
zDry the appliance by rubbing the surface with a clean cloth.
Stainless Steel Surface
The stainless steel surface should be cleaned with only a damp cloth or with a purpose made product such as
Steel Power from Hillmark or a few drops of olive oil on a damp cloth.
Hotplates
zWeekly cleaning of frequently used hotplates is recommended to maintain their surface finish.
zUse a small amount of concentrated household detergent and a nylon scourer to remove all baked on grime.
Wipe off with a damp cloth and dry with about 10 seconds of high temperature heat.
zApply a hotplate protector to the cleaned hotplates such as Solid Hotplate Protector from Hillmark or lightly
oil with olive oil while plate is still warm.
zThe chrome element rings around the hotplates will change colour over time due to the effect of the heat on
the metal. The colour changes are dependent on the temperature levels and is common to all electric
cooktops.

10
WARRANTY
1.1 In this warranty:
1.1.1 Australian Consumer Law means the law as set out in Schedule 2 of the Competition and
Consumer Act 2010;
1.1.2 Company means GSM Sales Pty Ltd ACN 007 682 475 of 101 Port Wakefield Road Cavan SA
5094. Telephone [phone]. Email [email protected];
1.1.3 Consumer means a “consumer” as that term is defined in Section 3 of the Australian Consumer
Law as the original purchaser of a Bellini product;
1.1.4 Consumer Guarantees means the guarantees under the Australian Consumer Law;
1.1.5 You means the Consumer.
1.2 Nothing in this warranty affects any person’s rights under the Australian Consumer Law. The benefits to
any Consumer under this warranty are in addition to the rights and remedies available under any
Consumer Guarantees.
1.3 Subject to the other clauses of this warranty, the Company warrants to the Consumer that the Bellini
product will be free of manufacturing defects and will perform to the Company’s specifications.
1.4 The benefit of this warranty extends only to the Consumer as original purchaser of a Bellini product which
is installed in a residential property.
1.5 This warranty commences on the date of purchase of the Bellini product by the Consumer and continues
for the benefit only of the Consumer until the expiry of two (2) years (Warranty Period).
1.6 If within the Warranty Period a manufacturing defect is discovered in the Bellini product or it fails to perform
to the Company’s specifications as a result of some defect in materials, components or workmanship
(Defect) then the Company will, at its option, repair the Bellini product or supply a replacement Bellini
product free of charge. A replacement Bellini product may differ from the original product purchased by the
Consumer.
1.7 This warranty will not apply to any Bellini product:
1.7.1 Installed by any person other than a qualified tradesperson; or
1.7.2 Subjected to misuse, neglect, negligence or accidental damage; or
1.7.3 Operated in any way contrary to any operating or maintenance instructions; or
1.7.4 Improperly handled, installed or maintained; or
1.7.5 Altered or modified prior to or after installation; or
1.7.6 Damaged directly or indirectly by power surges, electrical storm damage or connection to incorrect
power supply
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY THE
CONSUMER MUST CALL 1300 373 199 (AUSTRALIA) OR 0508 123 108
(NEW ZEALAND) TO CONNECT TO THE NEAREST AUTHORISED CENTRE
TheAustralianConsumerLawrequirestheinclusionofthefollowingstatement
withthiswarranty:
Our goods come with guaranteed that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.

11
1.8 You must provide proof of your purchase of the Bellini product and the date of purchase in order to obtain
the benefit of this warranty.
1.9 If you live outside the service area of the Company or one of its service agents, this warranty does not
cover the cost of transport of the Bellini product for service nor the service agent’s traveling costs to and
from your home.
1.10 If you are required to transport the Bellini product to the Company or its service agent, you must ensure it is
safely disconnected by a qualified tradesman and securely packed and insured. The Company does not
accept any responsibility for loss or damage of the Bellini product prior to it being received by the Company
or its service agent.
1.11 You will be responsible for all costs of returning a Bellini product to the Company and for redelivery of the
Bellini product by the Company (whether it is the original or a repaired and/or a replacement Bellini product)
and for any other expenses you incur in claiming under this warranty.
1.12 The Company or its service agent will examine any Bellini product and if the Company determines that it is
defective through no fault of the Owner and is otherwise undamaged, the Company will repair or replace
the Bellini product in accordance with this warranty.
DO NOT SEND IN THIS WARRANTY
Fill out the following details and file with your purchase invoice.
RETAIN & FILE WITH YOUR RECEIPT
Your Purchase Receipt/Invoice is proof of date of purchase. If you are unable to establish the date of purchase,
or if the fault is not covered by this warranty, or if the product is found to be in working order, you will be required
to bear all service call charges.
GSM Sales Pty Ltd reserves the right to discontinue items, modify designs and change specifications without
incurring obligation.
Whilst every effort is made to ensure that descriptions, specifications and other information in this publication is
correct, no warranty is given in respect thereof and the company shall not be liable for any errors therein.
Purchased from:
Co. Name:
Address:
Date of Purchase:
Serial number:
NOTE: Consistent with our continuing product development policy, improvements may have been made
which render the contents of this packaging slightly different to that shown.
FOR WARRANTY SERVICE CALL 1300 373 199 (AUSTRALIA)
OR 0508 123 108 (NEW ZEALAND) TO CONNECT YOU TO THE NEAREST
AUTHORISED SERVICE CENTRE