Bellini BCT604TG-F Installation instructions

GSM Retail Australia Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 Aust OR0800 764 912 NZwww.belliniappliances.com.au
Model: BCT604TG-FFINELINE: 5104068 Aus Only Also inBuilder Pack BPT350EC Fineline: 5104067 Aus Only 60cm Ceramic Cooktop
INSTALLATION & OPERATION
INSTRUCTIONS
60cm Ceramic Cooktop
Model No.
BCT604TG-F FINELINE: 5104068 Aus Only
BCT604TG
Also in Builder Pack BPT350EC Fineline: 5104067 Aus Only
V5 Sep20

Thank you
Thank you for choosing Bellini Appliances.
Bellini prides itself on ‘affordable living’ making sure there is
no compromise in your favourite room … The Kitchen
All Bellini appliances carry a 3 year In Home warranty,
be sure to retain your installation and user manual and
receipt.
For all warranty and technical queries please contact
1300 373 199
GSM Retail Australia Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 Aust OR0800 764 912 NZwww.belliniappliances.com.au
Model: BCT604TG-FFINELINE: 5104068 Aus Only Also inBuilder Pack BPT350EC Fineline: 5104067 Aus Only 60cm Ceramic Cooktop

Content
Safety instructions----------------------------- 2
Product description---------------------------- 4
Installation----------------------------------------5
Start using your appliance--------------------8
Maintenance ------------------------------------11
Warranty------------------------------------------ 12
GSM Retail Australia Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 Aust OR0800 764 912 NZ www.belliniappliances.com.au
Model: BCT604TG-FFINELINE: 5104068 Aus Only Also inBuilder Pack BPT350EC Fineline: 5104067 Aus Only 60cm Ceramic Cooktop

2
Important Safeguards
When using electrical appliances, in
order to reduce the risk of fire, electric
shock and/or injury, these basic safety
precautions should always be followed:
For Your Safety
Read all instructions carefully, even if you are
quite familiar with the appliance.
•Do not position this cooktop immediately below
or in front of a socket outlet.
•NEVER INSERT A KNIFE OR ANY OTHER
UTENSIL INTO THE HOB. This may damage
the mechanism and cause a safety hazard.
Contact with elements could result in electrical
shock.
•Take care not to burn hands on upper
elements when removing items from the Hob.
•To protect against the risk of electric shock DO
NOT IMMERSE of this appliance in water or
any other liquid.
•CAUTION: The temperature of cooktop or the
outer surface may be high when the appliance
is in operation.
•Switch off and remove the plug from the power
outlet before cleaning or when not in use.
•Do not operate any appliance with a damaged
cord or plug; after the appliance malfunctions,
or is dropped or damaged in any manner.
•Allow the appliance to cool before cleaning.
•Do not use the appliance for anything other
than its intended use. This product is intended
for household use only.
•Ensure the power cord does not touch the
cooker housing when in use.
•Dispose of packaging properly keeping plastic
bags away from babies and young children.
•Do not use outdoors.
•Do not attempt to repair or disassemble the
appliance. There are no user serviceable
parts.
•
The appliance should not be covered or
operated near or underneath flammable
material such as curtains or drapes or other
combustible materials when in operation.
•This appliance isnot intended for use by
persons (including children) with reduced
physical, sensory and mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use ofthe appliance bya person
responsible for their safety.
•Young children should be supervised
to ensure that they do not play with the
appliance.
•Do not operate in the presence of flammable
or explosive materials.
•Store the appliance indoors ina dry location.
•Metallic objects such as knives, forks, spoons
and lids should not beplaced on the hob
surface since they can get hot.
•The plug should beaccessible after installation
•This appliance isnot intended tobe operated
by means of an external timer orseparate
remote-control system.
•This appliance isdesigned for domestic
household use and for the cooking and frying
of domestic foodstuffs.
•IMPORTANT: The adjacent furniture and all
materials used in the installation must be able to
withstand a minimum temperature of 95°C
above the ambient temperature of the room it is
located in, whilst in use.
•Certain types ofvinyl or laminate kitchen
furniture are particularly prone toheat damage
or discolouration at temperatures below the
guidelines given above.
•Any damage caused by the appliance being
installed in contravention of this temperature
limit, will be the liability ofthe owner.
•You should not use this appliance to store items
onoras awork surface.
•You should not store orplace flammable or
highly flammable liquids/materials on top
or near the appliance. Items made from
aluminum, plastic orplastic film should also be
kept away from the appliance, asthey may
fuse to thesurface.
GSM Retail Australia Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 Aust OR 0508123108 NZ www.belliniappliances.com.au
Model: BCT604TG-F FINELINE: 5104068 Aus Only Also in Builder Pack BPT350EC Fineline: 5104067 Aus Only 60cm Ceramic Cooktop

3
•You should not allow the electrical connection
cables to come into contact with the hob
surface when it is hot or any hot cookware.
• Make sure that all of the cooking zones are
switched off after use.
•Always keep children away from the cooktop.
•While in operation direct contact with the
cooktop may cause burns!
•Ensure that small items of household
equipment, including connection leads, do
not touch the hob as the insulation material of
this equipment is usually not resistant to high
temperatures.
•Do not allow the hob to get soiled and prevent
liquids from boiling over onto the surface of the
hob, any spillages should be cleaned up as
they happen.
•Do not place pans with a wet bottom on the
warmed up heating zones as this can cause
irreversible changes to the hob(irremovable
stains).
•Do not switch on the hob until a pan has been
placed on it.
•Do not put pans weighing over 25kg on the
hob.
•Do not use the cooker in the event of a
technical fault. Any faults must be fixed by an
appropriately qualified and authorized person.
•The cooker should not be cleaned using steam
equipment or steam cleaner.
•WARNING - Accessible parts may become
hot during use. To avoid burn, young children
should be kept away.
•This cooking range must be connected to
the supply by a supply cord fitted with an
appropriately rated plug that is compatible with
the socket-outlet fitted to the final sub-circuit in
the fixed wiring that is intended to supply this
cooking range.
•CAUTION: The surface temperature exceeds
95°C. To avoid a hazard, underbench access
must be restricted. Refer to the installation
instructions.
•DO NOT USE THE HOB IF THE SURFACE
BECOMES BROKEN OR CRACKED.
Compulsory Warning
If the supply cord is damaged, the cord must be
replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a
hazard.
This product has not been designed for any uses
other than those specified in this booklet.
SaveTheseInstructions

4
Features of Your Hob
Heating Plate
Touch control pad

GettingtoKnow Your
Hob
Congratulations on the purchase of your new
Bellini Hob.
Before using your new Cooker, it is most
important that you read and follow the instructions
in this use and care booklet, even if you feel you
are familiar with this type of appliance.
Your attention is drawn particularly to the section
dealing with IMPORTANT SAFEGUARDS.
Find a safe and convenient place to keep this
booklet handy for future reference.
This appliance has been designed to operate
from a standard domestic power outlet. It is not
intended for industrial or commercial use.
How to Save Energy
Using energy in a responsible way not only saves
money but also helps the environment. So let’s
save energy! And this is how you can do it:
•Use proper pans for cooking. Pans with thick,
flat bases can save up to 1/3 on electric
energy. Remember to cover pans if possible
otherwise you will use four times as much
energy!
•Match the size of the saucepan to the surface
of the heating plates. A saucepan should
never be smaller than a heating plate.
•Ensure heating plates and pan bases are
clean. Soils can prevent heat transfer-and
repeatedly burnt -on spillages can often only
be removed by products which cause damage
to the environment.
•Do not uncover the pan too often (a watched
pot never boils!).
•Do not install the cooker in the direct vicinity
of refrigerators/freezers. Otherwise energy
consumption increases unnecessarily.
Installation
Positioning
This appliance must be correctly installed by a
suitably qualified person,
To avoid damaging your appliance.
•Cast iron and cast aluminium cookware with
damaged bases may scratch the hob surface if
they are dragged across it.
•Pans should be lifted on and off the hob
surface and not dragged.
•Cooking zones should not be switched on
without cookware placed on it. Also the
cookware should not be empty.
The adjacent furniture must be able
to withstand a minimum temperature
rise of95°C above the ambient
temperature of the room it is located
in, during periods of use.
Theappliance is to be built into a kitchen unit
(depending onsize) or600 mm worktop, providing
the following minimum distances are allowed:
•700 mm between the hob surface and the
underside of any horizontal surface above it.
•50 mm clearance around the appliance and
between the hob surface and any combustible
materials.
5

6
MODEL A B C D E
BCT604TG-F 580 510 560 490 53
Unpacking the appliance
When unpacking the appliance please check
that the following items are contained within the
packaging:
1 Ceramic hob
1 Installation and instruction manual
4 Fixing screws & clips
4 Clamps
1 Sealing strip
1 Cleaning kit
Installing the appliance
•Do not leave a gap in the sealing agent or
overlap the thickness.
•IMPORTANT: Do not use a silicon sealant to
seal the appliance against the aperture. This
will make it difficult to remove the hob from the
aperture in future, particularly if it needs to be
serviced.
Sealing strip
Hob and Aperture Dimensions
4x clip &
fixing screw
Installation Step
4x clamp 1 Cleaning kit
Firstly, insert the clip into the slot from side as fig
a,b &c.
•Cut a hole in the worktop that corresponds
with the drawings shown above.
•IMPORTANT: You must have a gap of at
least 25 mm between the underneath of the
appliance and any surface that is below it.
•Carefully turn the hob upside down and place
it on a cushioned mat.
•Apply the sealing strip provided around the
edge of the appliance.
•The protective covering must be removed from
both sides.
Secondly, place the clamp (B) over the holes that
match the size of the screws. There are one set
of screw holes in each corner of the hob. Slightly
tighten a screw (C) through the clamp (B) to which
the clamp is attached to the hob by the clips so
that you can still adjust the position of it as fig.D &
E finish other clamp & clip as same method.
Then, Carefully turn the hob back over and then
gently lower it into the aperture hole that you
have cut out.
Finally, on the underneath of the hob, adjust the
clamps into a position that is suitable for your
worktop. Then fully tighten the screws (C) to
secure the hob into position as fig e.
Fig. A

7
Fig. B
Fig. C (rear view)
Fig. D
Fig. E
Electrical connection
This appliance must be
installed by a qualified person.
Before connecting the appliance, make sure that
the supply voltage marked on the rating plate
corresponds with your mains supply voltage.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
•This appliance must be wired into a double
pole switched fused spur outlet, having 3 mm
contact separation and placed in an easily
accessible position adjacent to the appliance.
It should not be located above the appliance
and no more than 1.25m away from it.
•The spur outlet must still be accessible even
when your cooker is located in its operating
position.
Connecting the mains supply cable
•The mains terminal block is located on the
underside of the hob and the terminals are
accessible by removing the terminal block
cover by removing the cover screw.
•The cable connections must be in accordance
with the diagram located on the bottom of the
hob.
Replacing the mains supply cable
If the mains supply cable is damaged, then it
must be replaced by an appropriate replacement.
The mains supply cable should be replaced in
accordance with the following instructions:
•Switch the appliance off at the control switch.
•Open the terminal block on the underside of
the hob.
•Unscrew the terminal screws fixing the cable.
•Replace the cable with one of the same length
and in accordance with the specification given
above.
(A) Sealing strip
(B) Clamp
(C) Screw
Hard Wired Appliances :
When making the mains supply conductor connections to
the terminal block within the terminal box , please ensure
that minimum clearances are being maintained between
individual conductors and conductors/connectors to the
adjacent metal surfaces of the terminal box itself , where
possible add heat shrink sleeves to any bare conductor
end/connectors prior to securing.

8
Product dimensions:
L: x W: x H( mm) 580X510X55
Aperture
dimensions: L: x W:
x H( mm)
560X490
Product specifications:
4 Ceramic elements
2 x 1.8kw,
2 x 1.2kw
Electrical details
220-240 Vac 50 Hz
30 A (double pole
switched fused outlet
with 3mm contact gap)
Max Rated Inputs:
see the content on
rating label.
Mains Supply Lead:
H05RR-F 3 core x
2.5MM2 (not supplied)
Problems
Possible Cause and
solve
The cooking
zones are not
functioning or
will not switch
on.
Check that the mains
electrical supply to the
appliance is correct
and working. Check the
mains fuse.
A humming
sound is heard
when a cooking
zone is selected.
This is normal; the
sound will disappear
when the zone heats up
The cooking
zones have
become
discoloured
This maybe caused
by burnt on remnants
of food. This will not
affect the working of the
appliance. However you
should make sure that
the cleaning instructions
are being followed
regularly.
Only two of the
zones on my hob
are working
You should recheck
that the terminal screws
are all fully tightened
between the links.
•The “green-yellow” earth wire must be
connected to the terminal marked. It must be
about 10 mm longer than the live and neutral
wires.
•The “blue” neutral wire must be connected to
the terminal marked with letter (N) - the live
wire must be connected to the terminal marked
with letter (L).
Troubleshooting Guide
HowtoUseYourHob
Product specification
IMPORTANT: If your appliance appears not
to be operating correctly, then you should
disconnect it from your mains supply and
then contact the Service Department.
DO NOT ATTEMPT TO REPAIR THE
APPLIANCE YOURSELF. Plate layout
Before first use
IMPORTANT: You should clean the hob surface
and solid plates (see “Cleaning and maintenance”
section).
•You should switch on one cooking zone at a
time, for 5 minutes at the maximum setting.
This will help to eliminate any new smell that
exists and evaporate any humidity that has
formed on the heating elements during transit.

9
•When doing this burn off process, an
appropriately sized saucepan containing
cold water should be placed on the zone in
question.
•Do not burn off more than one zone at once.
Using the Hob
•Icons on the control pad as below:
1. Power Switch
2. Burner Switch
3. Burner Display
4. Minus
5. Plus
7. Timer
8. Timer Display
9. Children Safety Lock
11. Double Zone Indicator
12. Children Safety Lock Indicator
13. Burner Power Setting Indicator. If it is flash,
can set power. It no flash, can’t set power.
14. Single power indicator
•Operation of the touch pad:
1. Touch Power Switch, all power setting show
“0”, and Burner power setting indicator will
keep flashing. Need to make further operation
in 10S, otherwise it will turn off automatically.
2. Set power through “Plus” and “Minus”. First
touch plus, power will show “5”. First touch
minus, power will show “9”.
Remark:
a) Can operate one burner in one time.
b) If the burner is working, will show indicator
closed to burner.
c) Set power to “0”, burner will stop working.
•Children Safety Lock
For safety reason, you can lock the control by
pressing children safety lock. If power was off
before turn off the lock. The lock will keep working
when you restart power. Must turn off the lock for
further operation.
Power setting
Max working hour
1-2
6
3-4
5
5
4
6-9
1.5
•Stop Working
For safety reason, control panel will stop working if it
worked too long because of customer forget to turn
off the control.
After the control stop working, will show “H”
residential heating for 20 minutes.
•Auto Heating Mode
1. Set power to “9”, and then press plus, then
burner display will show “A” and “9” in turn. Now
it is auto heating mode. Then set the power you
need, for example, “6”, display will show “A”
and “6”, for 2.5 minutes (as below chart)
2. Auto heating mode will start when display show
“A” and “9” the first time. If you set power “6” for
10S, then display will show “A” and “6” for 2
minutes and 20S, and finally show “6” only.
3. Auto heating time
Power
Auto Heating time(minutes)
1
1
2
3
3
4.8
4
6.5
5
8.5
6
2.5
7
3.5
8
4.5
9
---
4. Auto heating setting. In this mode, when the
heating is working not exceed for 30S, press
minus, can reduce power. If more than 30S,
press minus, will stop auto heating mode, and
turn to regular heat mode. If more than 30S,
and display keep flashing “A” and power, can
press plus to have more power and still under
auto heating mode.
5. When you change power, the pasting time will
be calculated into time of auto heating mode of
new power. For example, you choose power “1”,
work for 30S, then change to power “4”, then
auto heating mode time will be 6 minutes only.

•Heat Time for Each Power
1 minutes for 1 cycle
Power：1，Time：Work for 1S, Stop for 59 S
Power：2，Time：Work for 3S, Stop for 57 S
Power：3，Time：Work for 6S, Stop for 54S
Power：4，Time：Work for 10S, Stop for 50 S
Power：5，Time：Work for 14S, Stop for 46S
Power：6 Time：Work for 19S, Stop for 41S
Power：7，Time：Work for 26S, Stop for 34S
Power：8，Time：Work for 38S, Stop for 22S
Power：9，Time：Keep working…
•Timer
1. Choose timer, display show “00”, press “Plus”
to set working time (01 to 99 minutes), press
“Minus” to set working time (30 to 0 minutes),
will confirm automatically in 10S.
2. Set timer for each burner. Press burner switch
to choose the burner, and the burner indicator
will flash, set power range, then press “Timer”,
will show “00”, then press “Plus” to set
working time (01 to 99 minutes), press “Minus”
to set working time (30 to 0 minutes), will
confirm automatically in 10S. Burner will stop
working if time was up.
Remark: can set new time by pressing “Plus”
or “Minus”.
3. Turn off timer. When time is up, timer will
sound for 2 minutes, and you can turn off
sound by touching any button. If you wanted
to turn off burner in advance, can set timer to
“00”.
Hob guidelines
•The first few times the hob top is used, it may
give off an acrid, burning smell. This smell will
disappear completely with repeated use.
•The positions where the heat will radiate
from are clearly marked on the hob top. The
saucepans must be positioned exactly on
these zones for efficient heating to occur. Pans
should have the same diameter as the cooking
zone that they are being used on.
•You should not use saucepans with rough
bottoms, as this can scratch the solid plates.
•Before use, make sure that the bottoms of the
saucepans are clean and dry.
•When cold, the bottom of the pans should be
slightly concave, as they expand when hot and
lie flat on the surface of the hob. This will allow
the heat to transfer more easily.
•The best thickness for the bottom of the pans
is 2 – 3 mm of enameled steel and 4 – 6 mm
for stainless steel with sandwich type bottoms.
•If these rules are not followed, then there will
be a great loss of heat and energy. Heat not
absorbed by the saucepan, will spread to the
hob, frame and surrounding cabinets.
•Preferably cover pans with a lid to permit
cooking at a lower heat.
10

11
CleaningYourHob
Disconnect the hob from the power outlet. Allow to
cool before cleaning.
•If a major spillage occurs inside the
compartment, wipe clean as soon as possible
with a damp cloth remembering to disconnect
from the power source first.
•Do not immerse in water.
•DO NOT use spray-on or other cleaners as
they may cause electrical damage. DO NOT
use sharp utensils to clean.
•Remove heavy splatters after use with a
nylon or polyester mesh pad, sponge or cloth
dampened with warm water. Blot dry with
paper towel or a soft, dry cloth.
Any residues that are left on the hob top surface
from cleaning agents will damage it. You should
remove any residues with water and a little
washing up.
Abrasive cleaners or sharp objects will damage
the hob surface; you should clean it using water
and a little washing up liquid.
Although it is easier to clean some deposits whilst
the hob surface is still warm. You should take care
not to burn yourself if cleaning the hob surface
when it is still warm.
After each use
•Wipe the appliance over with a damp cloth and
a little washing up liquid.
•Dry the appliance by rubbing the surface with
a clean cloth.
Using a specialist hob cleaner
It is possible to purchase specialist ceramic hob
cleaner/conditioner.
You should follow the instructions given by
the manufacturer of the specialist ceramic hob
cleaner. You should ensure that it is suitable for
use on your appliance.
Maintaining the solid plates
•If something is spilt onto the plate itself, then it
can be removed using a soft brush, plastic or
nylon scourer and warm water.
Regular inspections
Besides keeping the hob clean, you should:
•Carry out periodic inspections of the control
elements and cooking units of the hob. After
the guarantee has expired you should have a
technical inspection of the cooker carried out
at a service centre at least once every two
years.
Caution!
All repairs and regulatory activities should be
carried out by the appropriate service
centre or by an appropriately authorized fitter.

WARRANTY
1.1 In this warranty:
1.1.1 Australian Consumer Law means the law as set out in Schedule 2 of the Competition and
Consumer Act2010;
1.1.2 Company means GSM Retail Australia Pty Ltd ABN 53 007 682 475 of 142-144 Fullarton Road, Rose
Park SA5067. Telephone [phone]. Email [e-mail];
1.1.3 Consumer means a “consumer” as that term isdefined in Section 3 of the Australian Consumer
Law as the original purchaser of a Belliniproduct;
1.1.4 Consumer Guarantees means the guarantees under the Australian ConsumerLaw;
1.1.5 You means the Consumer.
1.2 Nothing in this warranty affects any person’s rights under the Australian Consumer Law. The benefits to
any Consumer under this warranty are in addition to the rights and remedies available under any
Consumer Guarantees.
1.3 Subject to the other clauses of this warranty, the Company warrants to the Consumer that the Bellini
product will be free of manufacturing defects and will perform to the Company’s specifications.
1.4 The benefit of this warranty extends only to the Consumer as original purchaser of a Bellini product which
is installed in a domestic household area.
*The in Home warranty does not apply to Commercial and or industrial usage. *Please See 1.7.7 for additional
information
1.5 This warranty commences on the date of purchase of the Bellini product by the Consumer and
continues for the benefit only of the Consumer until the expiry of three (3) year (Warranty Period).
1.6 If within theWarranty Period a manufacturing defect is discovered in the Bellini product or it fails to perform
to the Company’s specifications as a result of some defect in materials, components or workmanship
(Defect) then the Company will, at its option, repair the Bellini product or supply a replacement Bellini
product free of charge. A replacement Bellini product maydiffer from the original product purchased bythe
Consumer.
1.7 This warranty will not apply to any Bellini product:
1.7.1 Installed by any person other than a qualified tradesperson;or
1.7.2 Subjected to misuse, neglect, negligence or accidental damage;or
1.7.3 Operated in any way contrary to any operating or maintenance instructions;or
1.7.4 Improperly handled, installed or maintained;or
1.7.5 Altered or modified prior to or after installation; or
1.7.6 Damaged directly or indirectly bypower surges, electrical storm damage or connection to incorrect
power supply
1.7.7 Industrial and or Commercial usage is inclusive of staff areas in office/ shop environments, hotel/
motel or other similar accommodation or rental type properties including Bed and Breakfast
establishments.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY THE CONSUMER
MUST CALL 1300 373 199 (AUSTRALIA) OR0800 764 912
(NEW ZEALAND) TOCONNECT TOTHE NEAREST AUTHORISED CENTRE
The Australian Consumer Law requires the inclusion of the following
statement with this warranty:
Our goods come with guaranteed that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.

1.8 You must provide proof of your purchase of the Bellini product and the date of purchase in order toobtain
the benefit of thiswarranty.
1.9 If you live outside the service area of the Company or one of its service agents, this warranty does not
cover the cost of transport of the Bellini product for service nor the service agent’s traveling costs to and
from your home.
1.10 If you are required to transport the Bellini product to the Company or its service agent, you must ensure it is
safely disconnected by a qualified tradesman and securely packed and insured. The Company does not
accept anyresponsibilityfor loss or damage of the Bellini product prior to it being received bythe Company or
its serviceagent.
1.11 You will be responsible for all costs of returning a Bellini product to the Company and for redelivery of the
Bellini product by the Company (whether it is the original or a repaired and/or a replacement Bellini product)
and for any other expenses you incur in claiming under this warranty.
1.12 The Company or its service agent will examine any Bellini product and if the Company determines that it is
defective through no fault of the Owner and is otherwise undamaged, the Company will repair or replace the
Bellini product in accordance with thiswarranty.
DO NOTSEND IN THIS WARRANTY
Fill out the following details and file with your purchase invoice.
RETAIN & FILE WITH YOUR RECEIPT
Your Purchase Receipt/Invoice isproof of date of purchase. Ifyou are unable to establish the date of purchase, or if
the fault isnot covered by this warranty, or if the product isfound to be in working order, you will be required to bear
all service call charges.
GSM Retail Australia Pty Ltd reserves the right to discontinue items, modify designs and change specifications
without incurring obligation.
Whilst every effort ismade to ensure that descriptions, specifications and other information in this publication is
correct, no warranty is given in respect thereof and the company shall not be liable for anyerrors therein.
Purchased from:
Co. Name:
Address:
Date of Purchase:
Serial number:
NOTE: Consistent with our continuing product development policy, improvements may have been made
which render the contents of this packaging slightly different to that shown.
FOR WARRANTY SERVICE CALL 1300 373 199 (AUSTRALIA)
OR 0800 764 912 (NEW ZEALAND) TOCONNECT YOU TO THE NEAREST
AUTHORISED SERVICE CENTRE