Bellini BIA64EGP-W Installation instructions

GSM Retail Australia Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 Aust OR 0508123108 NZ www.belliniappliances.com.au
Model: BIA64EGP-W, BIA64EGP-F, BIA64EGP FINELINE: 60cm Induction Cooktop
INSTALLATION & OPERATION
INSTRUCTIONS
60cm Induction Cooktop
Model No.
BIA64EGP-W
FINELINE:0081479
BIA64EGP-F
BIA64EGP
V.3 June19

GSM Retail Australia Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: 1300 373 199 Aust OR 0508123108 NZ www.belliniappliances.com.au
Model: BIA64EGP-W, BIA64EGP-F, BIA64EGP FINELINE: 60cm Induction Cooktop
Thank you
Thank you for choosing Bellini Appliances.
Bellini prides itself on ‘affordable living’ making sure there is
no compromise in your favourite room … The Kitchen
All Bellini appliances carry a 3-year In Home warranty,
be sure to retain your installation and user manual and
receipt.
For all warranty and technical queries, please contact
1300 373 199

Content
3…………………………………..…………………Safety instructions
4-6…………………………………..………………Installation
7-9…………………………………..………………Description of the appliance
10…………………………………..………………..Fault code
11…………………………………..………………..Pots and pans and how to use them
12-13…………………………………..…………..Safety reminding and Maintenance and cleaning
14…………………………………..…………………Troubleshooting
15…………………………………..…………………Environmental note

Safety instructions
Important
This appliance generates magnetic field in the direct vicinity.
ATTENTION: People with PACEMAKERS must ensure that their pacemaker has been
designed in conformity with the norms in force. It is recommended that the manufacture or
your doctor is consulted to verify any incompatibility.
Important
This appliance generates short-range magnetic field therefore people with
other types of electrical medical equipment, such as hearing aids for the deaf,
must ensure they confirm to the norms regarding electromagnetic
disturbances.
This appliance has been designed for family use only. In case of doubts or questions,
please contact the manufacturer.
Keep the packing material away from children (plastic bags, parts in foamed plastic, etc.)
they could be potentially dangerous.
To prevent electrical shocks, contact the technical service centre for any repairs.
Make sure that installation and electrical connections are carried out by qualified personnel,
following the manufacturer’s instructions and in conformity with local norms in force.
The hob must be installed and grounded by qualified personnel. Do not repair or replace
any part of the appliance unless specifically recommended in this manual. All other
interventions must be carried out by qualified technicians.
This hob comes with a cooling fan with air vent underneath the worktop itself. If there is a
drawer under the worktop, do not put any paper or small light objects in it as they could be
sucked up by the fan, damaging it or compromising its function.
Do not use aluminium foil to protect parts of the hob.
Do not leave the kitchen unattended when cooking foods where high contents of oil or fat
are used, the oil could catch fire. If the oil catches fire never, put out with water. Immediately
suffocate the fire with a lid and turn off the hob.
Do not cook on the hob if the glass is broken. Water or cleaning products could filter
through the breakage and cause electrical shocks. Immediately contact qualified personnel
as soon as you notice a breakage.
Keep the area around the hob free from combustible material (plastic, paper etc.) or
flammable liquids, these can catch fire, metal parts can heat up and cause burns.
Children must not be along in the kitchen when the hob is in use.
After use, when the cooking element or entire hob is turned off, a residual heat indicator will
come on, showing an H (hot) for each cooking area that was used: this indicates that the
corresponding cooking area is still dangerous.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of
electric shock.

A steam cleaner is not to be used.
Metallic objects such as knives, forks, spoons and lids should not be placed on the hob
surface since they can get hot.
The appliance is not intended to be operated by means of an external timer or separate
remote-control system.
Danger of fire: Do not store items on the cooking surfaces.
CAUTION: The cooking process has to be supervised. A short-term cooking process has to
be supervised continuously.
WARNING: Use only hob guards designed by the manufacturer of the cooking appliance or
indicated by the manufacturer of the appliance in the instructions for use as suitable or hob
guards incorporated in the appliance. The use of inappropriate guards can cause accidents.
Children should be supervised to ensure that they do not play with the appliance.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Means for disconnection must be incorporated in the fixed wiring in accordance with the
wiring rules.
WARNING: The appliance and its accessible parts become hot during use.
Care should be taken to avoid touching heating elements.
After use, turn off the hob using the command device and do not rely on the pan
detector.
Important
The heating elements do not work if the pan has a diameter that is too small
or not magnetically detectable. To verify that the material of the pan is suitable,
that is ferrous, use a magnet. To prevent damage to the electronic circuit, the
hob has a sensor that constantly controls the temperature of the circuit itself:
in the case of overheating, the hob automatically reduces power or turns itself
off until a safe temperature is reached.

Installation
Preparing the unit for a built-in appliance
1. Drill a hole on the table surface according to the size shown in the drawing. For the purpose
of the installation and use, a minimum of 50mm space shall be preserved around the hole.
Be sure the thickness of the table surface should be at least 30mm.please select heat-
resistant table material to avoid larger deformation caused by the heat radiation from the
cooker. As shown in the Figure 1.
2. ATTENTION: important assembly instructions for keeping the induction module cold.
3. Do not install the hob on top of a refrigerator or dishwasher. If the hob is installed on top of a
drawer put a shelf in between as shown (50mm).If shelves are put in between ensure that
they allow air to flow (30mm).
Product dimensions
WARNING
The kitchen units that are in direct contact with the appliances must be heatproof (min. 95°).
The appliance can be installed on a work surface with a thickness of between 30 and 40 mm
and near to walls, which are higher than the work surface, maintaining a minimum distance
of 100 mm.

Carry out all cutting of the unit and work surface then carefully remove shavings or sawdust
before inserting the appliances.
To ensure a correct ventilation of the hob please comply with the dimensions shows in figures.
Always refer to the manufacturer for specific instructions,
Make sure the surface is level and square and that no part interferes with the space required
for installation.
Prepare the cut as indicated (see installation dimensions).
Installing the hob
WARNING
Risk of cutting.
Be careful of cutting edges.
End parts in foamed plastic - be careful.
During transportation, these could cause slight injury or cuts.
Remove the material and envelope of documents from the packaging.
Before proceeding with installation read the work instructions carefully.
Step.1
Put a towel or cloth on the work surface. Place the hob face down
on the protected surface.
Step.2
Apply the strip seal, supplied with the hob, which is for sealing it onto the
work surface.
Do not use silicone. Apply the seal to the edge of the bottom of the hob,
leaving about 3mm from the edge of the glass.
Apply the seal all around the circumference.
Cut any excess and bringthe two ends of the seal together so they match.
Step.3

Fix the brackets on the front side and rear side by screw. Put the induction hob in the cutout
cabinet.
Attention:
The electric hob is recommended to be installed by professional. Please never conduct the
operation by yourself.
The wall and the heating area above the table surface shall withstand heat.
To avoid danger, the ceramic cooker hob must be installed into the cabinet before use.
Applicable cabinet material: wood, marble resin etc.
Connect to the mains power supply
To connect the mains power supply, please follow these steps:
1) The “green-yellow” earth wire must be connected to the terminal marked. It
Must be about 10 mm longer than the live and neutral wires.
2) The “blue” or “black”neutral wire must be connected to the terminal marked with letter (N)
- The “red”or “brown”live wire must be connected to the terminal marked with letter (L).
Hard Wired Appliances : When making the mains supply conductor connections to the
terminal block within the terminal box, please ensure that minimum clearances are being
maintained between individual conductors and conductors/connectors to the adjacent metal
surfaces of the terminal box itself, where possible add heat shrink sleeves to any bare
conductor end/connectors prior to securing.
1. If the cable is damaged or needs replacing, this should be done by an after-sales
technician using the proper tools, to avoid any accidents.
2.If the appliance is being connected directly to the mains supply, an omnipolar Safety
instructions
Circuit breaker must be installed with a minimum gap of 3mm between the contacts.
3. The installer must ensure that the correct electrical connection has been made and that it

complies with safety regulations.
4. The cable must not be bent or compressed.
5. The cable must be checked regularly and only replaced by a properly qualified person.
Electrical principle diagram

Description of the appliance
Control Panel
Schematic diagram of the control panel
Instruction
1
ON/OFF: Turn ON or OFF the appliance.
2
CHILD LOCK: Press the button one time to lock keys (the indicator
light keep bright) and hold for a while to unlock, When it is activated,
none of the other buttons can be activated except for ON / OFF.
3
, ,
UP: Increase the power level or add the time.
4
, ,
DOWN: Reduce the power level or reduce the time.
5
Single digital tube: It shows power level and error code.
6
Twin digital tube: It shows time.
7
The left above burner.
8
The right above burner.

9
The left bottom burner.
10
The right bottom burner.
11
Timer: Setting the time as you need.
Display instructions
1) Display rule of the LED light
A. Switch indicator light: The indicator light will flash in standby state, and will remain on in
other states.
B. Function indicator light: the corresponding indicator light will not bright when not work. In
addition, it will stays bright when start working.
2) Display rule of the digital tube
A: In normal working:
Single digital tube (total four single digital tube): display the power level of each burner.
Twin digital tube: display the setting time of each burner.
B: When the digital tube fails, the single digital tube will display the error code (two single
digital tube will flash); and the twin digital tube will not displayed.
Operation
Operate and display requirement
(1) Standby status:
Plug in and connected to the electrical supply, the buzzer will “beep”a sound, all indicator
lights and all characters on the digital tube are lit for 1s, then the “ON / OFF”indicator lights
flash, and the child lock indicator lights keep bright to indicate that the induction cooker is in
standby condition.
(2) Power on status:
"ON / OFF" button used for switching ON and OFF the induction cooker.
A. Under standby state, press child lock, first unlock, then press "ON / OFF" button, power
indicator light always on, child lock indicator light does not show, Single digital tube display "-
", 20s without any operation, return to standby state. (10s no operation, Child lock indicator
light keep bright automatically lock.)
B. In working status, press the "ON / OFF" button to return to state of power-on, without any
operation in 20S will return to the standby state.
(3) Work status:
A. Choosing the cooking zone: Under power ON state, press the cooking zone select button,
enter to select the cooking zone, the default power level 5, single digital tube will display "5"
and flash. (If it is understandby state, it must be turned on first, then enter to select the cooking
zone, and then make appropriate operation.
B. Power level adjustment:
After select the cooking zone, when the single digital tube flash and display the power level,
press the +/- button to adjust the power level.

Each press of the “+”button, the power level increased by one unit; each press of the “-”
button, the power level reduced by one unit;
Power level:0,1,2,3,4,5,6,7,8,9.
Max power level: 9, Min power level: 1, 0 level close the power output.
In the working process, various faults are detected, and if occurs, the appliance will enter into
fault alarm processing state.
(4) Timer Control:
Under working condition, press cooking zone select button, when the twin digital tube flash,
press "timing" button to set the timer. The twin digital tube will display the timing and flash,
press the +/- button to set the timer.
Each press of the “+”button, the timer increased by one unit; Long press “+”button, the timer
is incremented in minute.
Each press of the “-” button, the timer reduced by one unit; Long press “-”button, the timer is
descended in minute.
Max time: 99 minutes, Min time: 1 minute.
Adjustable time range: 0-99 minutes recyclable.
The first time a timer is set, the default timing starts at "00".
Display: After setting the timing time, if there is no operation in 5s, the timing takes effect, the
timer of each cooking zone is alternately displayed 5s, when the cooking zone is displayed,
and the dot in the lower right corner of “8” will be displayed.
(5) Child Lock:
Standby state: child lock indicator light long lit, you must long press the child lock button to
unlock before entering the standby state.
Power on state or working state: The child lock indicator light is not on, but no operation in
10s will automatically locked, the child lock indicator light is always on. Unlock long press the
child lock button.
(6) Fan delay:
After shutdown, if the cooking surface temperature is above 50 ℃, fan will be delay 5 minutes
off. If the cooking surface temperature is below 50 ℃, the fan will be shut down immediately.

FAULT CODE
Fault
Code
Possible Cause
Description
E0
No pan or pot, or their
size, material, etc. is
not suitable, or not
placed precisely in
the middle of the
cooking area.
If no suitable pan or pot is placed on
after 60s, the hob will turn off
automatically; if suitable pan or pot
is placed within 60s, the hob will
start to work.
E1
Voltage is too low.
Lower than AC 160V.
E2
Voltage is too high.
Higher than AC 270V.
E3
IGBT overheat.
IGBT reaches 105±5℃for 3s (It can
recover automatically when
temperature decrease 50℃-70℃).
E4
Hob surface sensor
open-circuit
Power on and judge within 2
minutes.
Hob surface sensor
short-circuit
Power on and judge within 10S.
E5
IGBT sensor open-
circuit
Power on and judge within 2
minutes.
IGBT sensor short-
circuit
Power on and judge within 10S.
E6
Hob surface
overheat.
Hob surface temperature higher
than set value.
E7
Hob surface sensor
become invalid.
E9
Communication
failures.
Unplug or poor contact.
Eb
Line fault.
Coil panel is not connected.
H
Hob surface is of high
temperature.
After the hob is off, if the hob surface
temperature is too high, it will
display "H”, and the fan will delay
working for 5 minutes.

Pots and pans and how to use them
Attention
The pots and pans that can be used on this hob must be made of ferromagnetic material.
They can be made of enamoured steel, cast iron or special pans of stainless steel for
induction. The diameter of the pan should be at least 11cm.
To make sure a pan is suitable, try using a magnet to see if it sticks to the bottom of the pan.
Never use normal thin steel nor anything containing even just an amount of glass, terracotta,
copper or aluminium.
The display of the cooking area will show if the pan is suitable, if the power indicator flashes
the pan isnot suitable or thediameter of the bottom istoo small for the diameter of the cooking
area.
The pots and pans must be placed precisely in the middle of the cooking area.
In some cooking areas, an internal diameter is indicated, with a lighter outline, which advises
the user to go to a smaller cooking area, if available, with smaller diameter pan. This is to
obtain optimum performance and efficiency. You can however use pans with smaller
diameters than this limit.

Safety reminding
A dedicated power protection Never use the hob in high Never wash the hob with water
air switch must be incorporeted temperature environment. derectly. Steam cleaner is
in the fixed wiring in accordance not to be used.
with the wiring rules.
Never have the hob to work for sealed foods such as the appliance is not
Without food in pot, otherwise canned goods, please do not intended to be used by
Its operational performance heat them before opening children or handicapped
May be affected and danger their covers so as to avoid persons, unless they have
May happen. Any dangers of explosion due been supervised by a
To heating expansion. Responsible person to
Ensure they can use it
Safely.
Do not place rough or if the surface is cracked, pull do not put any detergents
Uneven appliances, which out the plug to avoid the or flammable materials in
May damage the ceramic possibility of electric shock. The equipment installed
Surface. Under the hob.
Because the hob can after being used, the If the supply is damaged, it
Generate very high corresponding heating must be replaced by the
Temperature, please use a zone of the hob is still hot. Manufacturer, its service
Pot resistant to a temperature Never touch the hob surface agent or similarly qualified
Of over 200. To avoid burn. Persons in order to avoid a
Hazard.

Maintenance and cleaning
1. Please shut off the power and pull out the plug before cleaning of the appliance.
2. Clean the appliance until it cools down completely.
3. To remove dirt, please select illustrious detergent.
4. After removing dirt, please use neat wet cloth to clean the unit.
5. Do not clean by water directly, water gets inside may cause malfunction.
6. Keep the crystal glass plate and pan clean before cook, otherwise dirt after charring is very
difficult to clean and the plate may get discoloration.
7. You may clean air vent / air entry’s dirt using vacuum cleaner to suck up. If there is dirt with
oil, add a little illustrious detergent with toothbrush to clean.
8. Don’t use caustic impregnates to clean? It may damage the cooker by chemical reaction.
Do not use scrubbing brush or polishing powder to clean the induction cooker.
Important
Periodically check that dust does not deposit under the fan or in the discharge openings, this
could obstruct ventilation for cooling the electronic system, reducing the efficiency of your
hob.
The hob could be damaged if hard and sharp edged objects fall on it, it is recommended that
such objects be kept away from the hob where they cannot fall on it.
Do not put hot pans on the control area or on the edge of the hob, do not use pans with a
raised design or pattern on the base, they could scratch the hob.
Cleaning techniques
Attention: When chemical products heat up them can corrode and damage the glass,
moreover the fumes can be dangerous for your health.
Clean the surface when it is completely cold except for the following: dried sugar, syrupy
sugar, tomato sauce, milk, these must be removed immediately with the scraper.
Cleaning after each use:
Dry any splashes with a damp sponge or paper
towel, rinse and dry. If any stains remain, use some vinegar, rinse and
dry.
Cleaning with cream detergents for glass hobs:
Apply a small amount of cream detergent for hobs, when dry, shine
the surface with a soft cloth or paper.

Do not use these products:
Abrasive powders or detergents, spray products for ovens, whitening products, sponges with
abrasive surfaces, steel wool balls or synthetic ones. These products could seriously damage
your hob.
Troubleshooting
Faults
Causes
Remedies
The appliance
does not work the
control lights are all
off.
The appliance is not
powered, the plant is
defective.
Check that the appliance is
connected, that there is
electricity and that the
current limiter or differential
has not intervened.
The appliance
turns off during use
and an intermittent
acoustic signal is
emitted.
The control may be dirty or
utensils may be on it.
Press any key to stop the
acoustic signal, clean the
control area or remove any
utensils and continue
cooking.
During cooking, the
hob makes a
noise.
The technology of
induction heating is based
on the capacity of certain
materials to vibrate when
subject to high frequency
waves. In some
conditions, whese
vibrations can produce
noise.
This is normal.
The control lights
continue to flash
when the hob is in
use.
The pan that is being used
is not suitable for
induction.
Verify that the pan is made
of suitable material by using
a magnet.
The fan continues
to work even after
the appliance has
been turned off.
The electronics of the
appliance have a high
temperatureandmustcool
down.
This is normal. Once the
appliance has cooled down
the fan will automatically
turn off.

Environmental note
Note: Before discarding an old appliance, switch off and disconnect it from the power supply.
Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person.
This product must not be disposed together with domestic waste. This product
has to be disposed at an authorised place for recycling of electrical and
electronic appliances. By collecting and recycling waste, you help save natural
resources, and make sure the product is
disposed in an environmental friendly and healthy way.

WARRANTY
1.1 In this warranty:
1.1.1 Australian Consumer Law means the law as set out in Schedule 2 of the Competition and Consumer
Act 2010;
1.1.2 Company means GSM Retail Australia Pty Ltd ABN 53 007 682 475 of 142-144 Fullarton Road, Rose
Park SA 5067. Telephone [phone]. Email [email protected]om.au;
1.1.3 Consumer means a “consumer” as that term is defined in Section 3 of the Australian Consumer Law
as the original purchaser of a Bellini product;
1.1.4 Consumer Guarantees means the guarantees under the Australian Consumer Law;
1.1.5 You means the Consumer.
1.2 Nothing in this warranty affects any person’s rights under the Australian Consumer Law. The benefits to
any Consumer under this warranty are in addition to the rights and remedies available under any
Consumer Guarantees.
1.3 Subject to the other clauses of this warranty, the Company warrants to the Consumer that the Bellini product
will be free of manufacturing defects and will perform to the Company’s specifications.
1.4 The benefit of this warranty extends only to the Consumer as original purchaser of a Bellini product, which
is installed in a domestic household area.
*The in Home warranty does not apply to Commercial and or industrial usage. *Please see 1.7.7 for
additional information
1.5 This warranty commences on the date of purchase of the Bellini product by the Consumer and continues
for the benefit only of the Consumer until the expiry of three (3) year (Warranty Period).
1.6 If within the Warranty Period a manufacturing defect is discovered in the Bellini product or it fails to perform
to the Company’s specifications as a result of some defect in materials, components or workmanship
(Defect) then the Company will, at its option, repair the Bellini product or supply a replacement Bellini
product free of charge. A replacement Bellini product may differ from the original product purchased by
the Consumer.
1.7 This warranty will not apply to any Bellini product:
1.7.1 Installed by any person other than a qualified tradesperson; or
1.7.2 Subjected to misuse, neglect, negligence or accidental damage; or
1.7.3 Operated in any way contrary to any operating or maintenance instructions; or
1.7.4 Improperly handled, installed or maintained; or
1.7.5 Altered or modified prior to or after installation; or
1.7.6 Damaged directly or indirectly by power surges, electrical storm damage or connection to incorrect
power supply
1.7.7 Industrial and or Commercial usage is inclusive of staff areas in office/ shop environments, hotel/ motel
or other similar accommodation or rental type properties including Bed and Breakfast establishments.
The Australian Consumer Law requires the inclusion of the following statement
with this warranty:
Our goods come with guaranteed that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY THE CONSUMER
MUST CALL 1300 373 199 (AUSTRALIA) OR 0508 123 108
(NEW ZEALAND) TO CONNECT TO THE NEAREST AUTHORISED CENTRE

20
1.8 You must provide proof of your purchase of the Bellini product and the date of purchase in order to
obtain the benefit of this warranty.
1.9 If you live outside the service area of the Company or one of its service agents, this warranty does
not cover the cost of transport of the Bellini product for service nor the service agent’s traveling
costs to and from your home.
1.10 If you are required to transport the Bellini product to the Company or its service agent, you must ensure
it is safely disconnected by a qualified tradesman and securely packed and insured. The Company does
not accept any responsibility for loss or damage of the Bellini product prior to it being received by the
Company or its service agent.
1.11 You will be responsible for all costs of returning a Bellini product to the Company and for redelivery of
the Bellini product by the Company (whether it is the original or a repaired and/or a replacement
Bellini product) and for any other expenses you incur in claiming under this warranty.
1.12 The Company or its service agent will examine any Bellini product and if the Company determines that it
is defective through no fault of the Owner and is otherwise undamaged, the Company will repair or
replace the Bellini product in accordance with this warranty.
DO NOT SEND IN THIS WARRANTY
Fill out the following details and file with your purchase invoice.
RETAIN & FILE WITH YOUR RECEIPT
Your Purchase Receipt/Invoice is proof of date of purchase. If you are unable to establish the date of purchase,
if the fault is not covered by this warranty, or if the product is found to be in working order, you will be required
to bear all service call charges.
GSM Retail Australia Pty Ltd reserves the right to discontinue items, modify designs and change
specifications without incurring obligation.
Whilst every effort is made to ensure that descriptions, specifications and other information in this
publication is correct, no warranty is given in respect thereof and the company shall not be liable for any
errors therein.
Purchased from:
Co. Name:
Address:
Date of Purchase:
Serial number:
NOTE: Consistent with our continuing product development policy, improvements may have been made
which render the contents of this packaging slightly different to that shown.
FOR WARRANTY SERVICE CALL 1300 373 199 (AUSTRALIA)
OR 0508 123 108 (NEW ZEALAND) TO CONNECT YOU TO THE NEAREST
AUTHORISED SERVICE CENTRE