Bellini BDOM609TCX User manual

1
60cm Built In
Touch Oven
Installation and User manual
Content
Important Safety instructions-------------------- 2
Product description--------------------------------- 4
Installation-------------------------------------------- 7
Start using your oven------------------------------- 9
Troubleshooting --------------------------------------12
Maintenance and cleaning------------------------ 13
Warranty----------------------------------------------- 15
BDOM609TCX
BDOM609TCX-F
20150428 Issue 2
For warranty service call 1300 373 199(Australia)
or 0508 123108(New Zealand) to connect you to
the nearest authorised service centre

Important Safety Instructions
This manual explains the proper installation and use of your oven, please read it carefully before
using even if you are familiar with the product. The manual should be kept in a safe place for future
reference.
General Warnings
If the supply cord is damaged, the cord must be
replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a
hazard.
This product has not been designed for any uses
other than those specified in this booklet.
This appliance must not be used as a space
heater.
In order to avoid fire, the appliance must be kept
clean and vents kept unobstructed.
Do not spray aerosols within the vicinity of the
appliance during operation.
Do not store flammable materials in or under the
appliance, e.g. aerosols.
Do not line the bottom of the oven with foil or
cookware.
Always use gloves when handling hot items inside
the oven.
Always turn the grill off immediately after use as
fat left behind may catch fire.
Do not leave the appliance unattended when
cooking. Oils and fats may catch fire due to
overheating or boiling over.
Do not put pans weighing over 15Kgs on the
opened door of the oven.
Do not use the appliance in the event of a
technical fault. Any faults must be fixed by an
appropriately qualified and authorised person.
In the event of any incident caused by a technical
fault, disconnect the power and report the fault to
the service centre to be repaired.
The rules and provisions contained in this
instruction manual should be strictly observed.
Do not allow anybody who is not familiar with the
contents of this instruction manual to operate the
appliance.
Child Safety
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they’ve been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
During use this appliance becomes hot. Care
should be taken to avoid touching hot surfaces, e.g.
oven door, heating elements.
Accessible parts will also become hot when in use.
To avoid burns and scalds children should be kept
away.
Installation, Cleaning & Servicing
The appliance must be installed only by an
authorised person in compliance with the
instructions provided. Incorrect installation may
cause harm to persons, animals or may damage
property.
Before using the appliance, ensure that all packing
materials are removed from the appliance.
In order to avoid any potential hazard, the
enclosed installation instructions must be followed.
Ensure that all specified vents, openings and air
spaces are not blocked.
The panels adjacent to the oven must be made of
heat-resistant material.
Cabinet with a veneer exterior must be assembled
with glues which can withstand temperature of up
to 120C.
2

To reduce the risk of fire, do not place or install
this unit in areas where the ventilation or
circulation ducts may become blocked. Make sure
there are at least 10mm of space between the
back of your oven and the wall. Keep some
distance on each side of your oven that you can
use that distance flowing installing instructions.
The unit's power cord must be connected to a
properly grounded and protected, 220-240V
electrical outlet. Always use ground fault
protection where required by the electrical code.
When transporting or storing the unit, keep it in a
dry location, free from dust, excessive vibration or
other factors, which may damage the unit.
Do not operate oven with a damaged cord, plug or
if the oven has malfunctioned or has been
dropped or damaged in any manner. Return
oven to authorised service facility for repair.
Only authorised personnel should carry out
servicing. (Certificate of Compliance to be
retained)
Always ensure the appliance is switched off
before cleaning or replacing parts.
Do not use steam cleaners, as this may cause
moisture build-up.
Always clean the appliance immediately after any
food spills.
THIS APPLIANCE MUST BE EARTHED.
To maintain safe operation, it is recommended
that the product be inspected every five years by
an authorised service person.
Oven
During use the appliance becomes hot. Care
should be taken to avoid touching the hot surfaces
inside the oven.
Switch the appliance off before removing the oven
light glass for globe replacement.
To avoid an accident, ensure that oven shelves
and fittings are always inserted into the appliance
in accordance with the instructions.
Do not use the door as a shelf.
Do not push down when the oven door is open.
Grill
Do not cover the grill insert with foil, as fat built up
may catch on fire.
Always keep the grill dish clean as any build up
may catch on fire.
Do not leave the grill on unattended.
To avoid fire, ensure that grill trays and fittings are
always inserted into the appliance in accordance
with the instructions.
Do not place thick portions of food under the grill.
Foods may curl, catch and ignite.
Accessible parts may become hot when grill is in
use. Children should be kept away.
Environmental Hints
Use the oven efficiently, by cooking many trays of
food at the same time.
Cook 2 trays of scones, small cakes or sausage
rolls at the same time.
Select the correct shelf location for food being
cooked.
Do not open the oven door more than necessary.
After the oven is turned off it retains heat for some
time.
This product must not be disposed together
with domestic waste. This product has to be
disposed at an authorised place for recycling
of electrical and electronic appliances.
By collecting and recycling waste, you help save natural
resources, and make sure the product is disposed in an
environmental friendly and healthy way.
3

Product Description
LED display
A B
C
D
A/B
C Door Handle
D 3 Layers Glass Door
Clock setting button
Alarm Timer/Delay start setting button
Function setting button
Decrease setting button
Increase setting button
Temperature/Cooking Time setting button
Stop button
Start button
Function Pad
4

Accessory Name Picture Quantity
Baking tray 1 pair
Grill rack
2
Distant holder
2
Screws(ST4x3 ) 2
Technical Specifications
product
dimensions
(h x w x d) mm net weight
usable
capacity
electrical
connection
max. power
rating
595 x 595 x 575 Approx. 32Kg 65 litres 220-240V/50Hz 3.0kW
0
5

Installation
WARNING!
Please follow the points below when installing the appliance
Use An Authorized Person
As stated in the local municipal building codes
and other relevant statutory regulations:
Wiring connections must be in accordance with
AS/NZS 3000 Wiring Rules and any particular
conditions of the local authority.
Refer to data plate for rating information. The
data plate is positioned at the side of cavity.
A functional switch should be provided near the
appliance in an accessible position. Refer to
AS/NZS 3000 clause 4.7.1.
Wiring should be protected against mechanical
failure. Refer to AS/NZS 3000 clause 1.5.
A means of disconnection with a contact
separation of at least 3mm must be supplied in
the fixed wiring.
Disconnect the power plug of the appliance from
the power point when conducting maintenance
or repairs to the unit

This Appliance Must Be Properly Earthed
Do not lift the appliance by the door handles.
Prepare the cupboard opening to match your
appliance measurements. (See diagrams).
Slide appliance in to cabinet cavity, ensuring
supply cable is not obstructed (kinked, jammed
or twisted).
To prevent tipping or dislodging of the appliance,
secure appliance to the cabinet with 2 screws
(provided), through the dedicated holes in the
appliance frame.
Where the appliance is built into a cabinet, the
cabinet material must be capable of withstanding
120°C. Installation into low temperature tolerant
cabinetry (E.g. vinyl coated) may result in
deterioration of the low temperature coating by
discoloring or bubbling.
The cabinet panels to the oven must be heat
resistant. With veneered wood units, glues must
be resistant to a temperature of 100C.
If the appliance is to be installed adjacent to vinyl
wrapped surfaces, use an installation kit
available from the vinyl-wrap supplier.
GSM cannot accept responsibility for damage
caused by installation into low temperature
tolerant cabinets.
After installation, test and ensure the appliance
operates correctly before handing it over to the
customer.
CAUTION!
Where the appliance is connected via power supply
cable to a power point, the installed power point must
remain accessible after appliance installation
A dedicated power circuit is recommended for the unit
but not required. Additional electrical appliances on
the same circuit may exceed the current (amperage)
rating for that circuit. If after the installation of your
unit the circuit breaker trips or the fuse fails on a
repeated basis, then a dedicated circuit will likely be
required.
WARNING!
To avoid any potential hazard, you must
follow our instructions when you install
your appliance. Failure to install the
appliance correctly could invalidate any
warranty or liability claims and lead to
prosecution.
Install the shelf
1. Pay attention to high temperature, you may need
to wear gloves if it is hot inside.
2. Always slide shelves into the layer with stopper.
6

Cut-out dimensions
Secure the oven to cabinet
Fit oven into the cabinet recess.
Open the oven door.
Secure the oven to the kitchen cabinet with two distance holders "A" which fit the holes in the oven frame
and fit the two wood screws "B".
7
590
7

Start Using Your Oven
Clock setting
The oven has 24 hours clock, only in standby mode, the clock can be set. To set the clock, please follow
1. Press clock setting button “ ” once.
3. Press clock setting button “ ”once again.
4. Press “<” or “>” button to set minute of clock time.
5. Press clock setting button “ ”again to confirm clock time setting. After clock setting, display shows the
time, and oven resume to standby mode.
-If you have set the clock time, when cooking, you can check the clock time by press “ ” once. The display
will show clock time for 3 seconds.
-When setting clock time, if press Stop “ ” button, current clock time setting would be canceled. Display
would show previously clock setting, if not yet set clock time, will show “0:00”.
-Long press on “<” or “>” button can fast backward or forward for clock time setting.
below steps:
Alarm timer setting
The oven Alarm timer function could help to remind you in the setting time. To set alarm timer, please follows
below steps:
1. Press Alarm Timer/Delay start setting button “ ” once, “0:00” and alarm timer icon “ ” shows in
2. Press Increase setting button “<” or decrease setting button “>” to set Alarm timer time.
3. Press start button “ ” to confirm alarm timer setting.
The oven buzzer will sound for 10 times when reach the setting time. During Alarm timer setting, you
can cancel it by press stop button “ ” once. After confirm Alarm timer setting, you can cancel it by press
stop button “ ” twice.
display.
This function is to disable oven button, to avoid children altering selected programmer in unconscious.
Press start “ ” and stop “ ” together for about 4 seconds, oven child lock will efficient. Oven buzzer
sounds once, and child lock icon “ ” illuminates in display. During this function, all press of oven button invalid.
To cancel the child lock, press start “ ” and stop “ ” together for about 4 seconds again. The oven
” disappears.
-Child lock function is only in order to make no efficient practice for oven buttons; it wouldn’t cancel the clock
time, cooking or any other setting.
-When child rock or standby mode, if there is no efficient practice for oven in 10 minutes. Oven display will
auto turn off to save electricity. The programmer still works during it and then will be resumed by press start
-When standby, if press start button “ ” for 3 seconds, oven display would turn off to save electricity and
buzzerers would sounds once, and child lock icon “
Safety Child Lock setting
Notes:
Notes:
Notes:
2. Press “<” or “>” button to set hour of clock time.
key and stop key only.
then will be resumed by press start key and stop key only.
Notes:
When using oven for the first time, you need to burn the oven in for approximately 1 Hour at 240
Degrees to remove any smells from the oven. During this time light smoke may emit from the oven( This
is normal ), so please ventilate kitchen by opening windows during this time. Ensure that all packaging
material is removed before first starting oven.
8

Function Description
0 Switch off function
Oven Light
Enables the user to observe the progress of cooking without opening the door
Defrost
The circulation of air at room temperature enables quicker thawing of frozen food,
(Without the use of any heat). It's a gentle but quick way to speed up the defrosting
time and thawing of ready-made dishes and cream filled produce etc.
Bottom Element
A concealed element in the bottom of the oven provides a more concentrative heat to
the base of food without browing It’s ideal for slow cooking dishes such as casseroles,
stews, pastries and pizzas where a crispy base is desired. The temperature can be set
within range 60-120C. The default temperature is 60C.
Conventional cooking
The top and bottom work together to provide conventional cooking.
The oven needs to be pre-heated to the required temperature, and is idea for single
items, such as large cakes. Best results are achieved by placing food in the center of
the oven. The temperature can be set within the range of 50-250C. The default
temperature is 220C.
Convention with fan
Combination of the fan and both heating element provides more even heat
penetration, saving up to30-40% of energy. Dishes are lightly browned on the outside
and still moist on the inside.
Note: This function is suitable for grilling or roasting big pieces of meat at a higher
temperature. The temperature can be set within the range of 50-250C. The default
temperature is 220C.
Radiant grill
The inner grill element switches on and off to maintain temperature.
Best results can be obtained from using the top shelf for small items and lower shelves
for large items. The temperature can be set within the range of 180-240C.
The default temperature is 210C.
Combined Grill
(Grill & Top element)
The inside radiant element and top element are working.
The temperature can be set within the range of 180-240C. The default temperature is
210C.
Combined grill with fan
The inside radiant element and top element are working with fan
The temperature can be set within the range of 180-240C. The default temperature is
210C.
Rear heater with fan
An element around the convection fan provides an additional source of heat
for convection style cooking. In this mode the fan automatically comes on to
improve air circulation within the oven and creates an even heat for cooking.
The temperature can be set within the range of 50-240C. The default temperature is
180C.
9

Cooking setting
Only when oven in standby mode, one can set cooking function follows below steps:
1. Press function setting button “ ” to set the cooking function you want. Press Function setting button “ ”
successively, you can switch for different function, follows sequence
.
2. Select the functions you want, then press “<” or “>” button to adjust cooking time. After that, you can also
adjust cooking temperature setting, by press button Temperature/Cooking Time “ ” switch to cooking tem-
perature setting, then press “<” or “>” button to adjust cooking temperature under this cooking function.
3. Press start button “ ” to confirm setting and start cooking.
Note:
-If do not adjust setting for cooking time and temperature, directlypress start button “ ”, you can also start
cooking with default setting temperature and cooking time.
- In “ ”and “ ” function, can’t adjust cooking temperature.
-If the temperature of oven cavity not yet reaches the temperature setting, temperature setting icon in display
will flashing. After temperature of oven cavity reach oven cooking temperature setting, oven buzzer sounds
once, and temperature setting icon stop flashing, keep on illuminate.
During cooking, you can adjust cooking time and cooking temperature follows below steps:
1. Press Temperature/Cooking Time setting button “ ” once, the temperature indicator “ ” illustrate in
display. Then press “<” or “>” button to adjust cooking temperature.
2. Press Temperature/Cooking Time setting button “ ” another time, the temperature indicator “ ” dis-
appear in display. Then press “<” or “>” button to adjust cooking time.
3. After above adjustment for cooking temperature or cooking time, please remember to press start button
“ ” to confirm the setting. If there is no confirmation after above adjustment in 5 seconds, programmer will
resume to previously setting.
Press for Temperature/Cooking Time setting button “ ”, could switch between temperature setting
and Cooking Time setting. During cooking, if press stop button “ ”once, cooking will be suspended. If press
stop button twice, you can cancel current cooking setting.
Notes:
Delay Start Function
The oven could be set to auto start under selected cooking function in the setting time. To set delay start func-
tion, first you need to set the clock time.
After clock time setting, you can use this setting follows below steps:
1. Press Alarm Timer/Delay start setting button “ ” twice, the delay start function icon “ ” and “End” will
show in display.
2. Press “<” or “>” button to adjust the hours you want to for delay start, then press Alarm Timer/Delay start
setting button “ ”. After that, press “<” or “>” button to adjust the minutes you want to for delay start, to finish
delay start time setting.
3. Press Function setting button “ ” to select cooking function for delay start. The delay start function icon
“ ”, cooking function icon, cooking time and cooking temperature will illuminate in display.
4. Press “<” or “>” button to adjust cooking time. After that, you can also adjust cooking temperature setting, by
press button Temperature/Cooking Time setting button “ ” switch to cooking.
---- - -- -
10

5. Press start button “ ” to confirm delay start function. The delay start function icon “ ” and clock time will
illuminate on display.
Note:
-The time set for auto start, must be after current clock time!
-After delay start setting, you can check the setting auto start time, by press clock time button “ ”, the auto
start time will illuminate for 3 seconds.
-Function can’t be set together with delay start function.
-After delay start setting, if press stop button “ ” once, would pause delay start setting; When pause the de-
lay start setting, press start button “ ” once could resume delay start function. While if the delay start setting
time already passed, delay function would not work when press start button “ ”.
-After delay start setting, if press stop button “ ” twice, would pause delay start setting;
-Delay start function and Alarm reminder function, can’t not be set together.
11

Troubleshooting
In the event of an emergency, you should:
Switch OFF all controls of the appliance
Disconnect the mains plug
Call the service centre
Some minor faults can be fixed by referring to the instructions given in the table below. Before calling the
customer support centre or the service centre check the following points that are presented in the table.
faults causes remedies
The upper crust is dark and
the lower part too pale
Not enough heat from the bottom -Use the natural convection position
-Use deeper cake tins
-Lower the temperature
-Put the cake on a lower shelf
The lower part is dark and
the upper crust too pale
Excessive heat from the bottom -Use the natural convection position
-Use lower side tins
-Lower the temperature
-Put the cake on a higher shelf
The outside is overcooked
and the inside is not cooked
enough
Temperature is too high -Lower the temperature and increase the
cooking time
The outside is too dry even
though it looks cooked
Temperature is too low -Increase the temperature and reduce the
cooking time.
The appliance does not work Break in power supply Check the household fuse box, if there is a blown
fuse replaces it with a new one.
The oven lighting does not
work
Bulb is loose or damaged Tighten up or replace the blown bulb (see chapter
Cleaning and Maintenance)
Display show Er-1 Sensor open circuit Call Service center
Display show Er-2 Sensor short circuit Call Service center
Display show Er-3 Meat probe short circuit N/A for this model
Display show Er-4 Oven cavity temperature higher
the 320C. Normally happen
restart pyrolytic function when
oven cavity still very hot.
Press , wait until oven cavity temperature cool
down then restart.
Display show Er-5 Temperature rise is abnormal in
pyrolytic function. Press , try to restart oven, if still not fixed, call
service center.
Display show Er-6 Door locker is not activated
Press , Close oven door completely then try
pyrolytic function again.
Display show “DOOR” Door opened or not closed well
during pyrolytic Press , close oven door completely then try
pyrolytic function again.
12

Maintenance and Cleaning
WARNING!
Before cleaning your oven, or performing maintenance, disconnect it from the
power supply.
Do not use steam cleaners.
Do not line the oven bottom with aluminium foil, as the consequent accumulation of
heat could compromise the cooking and even damage the enamel.
To protect against the risk of electrical shock, do not immerse the unit, cord or plug
in water or other liquid or sprinkle water to clean the appliance!
Do not clean the appliance when it is still hot! The inside and external surface of
the oven should preferably be cleaned with a damp cloth when it has cooled down.
Wash all accessories in hot sudsy water or in a dishwasher, wipe dry with a paper
or cloth towel.
If you use your oven for an extended period of time, condensation may form. Dry it
using a soft cloth.
Stainless steel
All grades of stainless steel can stain, discolour or become greasy. You must clean these areas regularly by
following the procedures below, if you want your appliance to look its best, perform well and have a long life.
Care must be taken when wiping exposed stainless steel edges, they can be sharp!
The front frame around the oven can be cleaned with stainless steel cleaners if it becomes soiled or
discoloured.
The stainless steel should only be cleaned with warm water and a mild detergent.
DO NOT use abrasive cleaners or harsh solvents.
NOTE: Make sure you follow the polish or brushing lines in the stainless steel
Glass
Glass surfaces on doors and control panels are best cleaned immediately after soiling.
A damp cloth may help remove baked on food deposits.
Oven cleaners can be used to remove stubborn marks and stains.
The glass door on this appliance is made from a tough, durable material that withstands heating and cooling
without breaking.
However, it must be remembered that it is GLASS, it may break. Treat it accordingly!
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door since they can scratch
the surface, which may result in shattering of the glass.
Oven
Always keep your appliance clean. Ensure fats and oils do not accumulate around elements, burners or fans.
Always keep the oven dish, baking trays and grill dish inserts clean, as any fat deposits may catch fire.
Always wrap your meats in foil or an oven roasting bag to minimise cleaning. Any polyunsaturated fats can
leave a varnish-like residue which is very difficult to remove.
Grill
Always keep the grill dish and grill insert clean, as any fat deposits may catch fire.
13

Replacement Of The Oven Light Bulb
WARNING!
In order to avoid the possibility of an electric shock ensure that the appliance is
disconnected from the power supply before replacing the bulb.
Set all control knobs to the “OFF” position (●/ 0)
and disconnect the mains plug.
Unscrew and wash the lamp cover and then
wipe it dry.
Unscrew the light bulb from the socket, replace
the bulb with a new one-a high temperature bulb
(300C) with the following parameters:
-voltage230 V
-power 25 W
-thread E14
Screw the bulb in, making sure it is properly
inserted into the ceramic socket.
Screw in the lamp cover.
Door Removal
In order to obtain easier access to the oven chamber
for cleaning, it is possible to remove the door. To do
this, tilt the safety catch part of the hinge upwards.
Close the door lightly, lift and pull it out towards you.
In order to fit the door back on to the oven, do the
inverse. When fitting, ensure that the notch of the
hinge is correctly placed on the protrusion of the
hinge holder. After the door is fitted to the oven, the
safety catch should be carefully lowered down again.
If the safety catch is not set it may cause damage to
the hinge when closing the door.
Removal Of The Internal Glass Panel
Slide glass toward direct 1 and directly lift the glass as
direction 2, then slide out glass carefully.
14

WARRANTY
1.1 In this warranty:
1.1.1 Australian Consumer Law means the law as set out in Schedule 2 of the Competition and
Consumer Act 2010;
1.1.2 Company means GSM Sales Pty Ltd ABN 53 007 682 475 of 142-144 Fullarton Road, Rose
Park SA 5067. Telephone . Email [email protected];
1.1.3 Consumer means a “consumer” as that term is defined in Section 3 of the Australian Consumer
Law as the original purchaser of a Bellini product;
1.1.4 Consumer Guarantees means the guarantees under the Australian Consumer Law;
1.1.5 You means the Consumer.
1.2 Nothing in this warranty affects any person’s rights under the Australian Consumer Law. The benefits to
any Consumer under this warranty are in addition to the rights and remedies available under any
Consumer Guarantees.
1.3 Subject to the other clauses of this warranty, the Company warrants to the Consumer that the Bellini
product will be free of manufacturing defects and will perform to the Company’s specifications.
1.4 The benefit of this warranty extends only to the Consumer as original purchaser of a Bellini product which
is installed in a residential property.
1.5 This warranty commences on the date of purchase of the Bellini product by the Consumer and continues
for the benefit only of the Consumer until the expiry of two (2) years (Warranty Period).
1.6 If within the Warranty Period a manufacturing defect is discovered in the Bellini product or it fails to perform
to the Company’s specifications as a result of some defect in materials, components or workmanship
(Defect) then the Company will, at its option, repair the Bellini product or supply a replacement Bellini
product free of charge. A replacement Bellini product may differ from the original product purchased by the
Consumer.
1.7 This warranty will not apply to any Bellini product:
1.7.1 Installed by any person other than a qualified tradesperson; or
1.7.2 Subjected to misuse, neglect, negligence or accidental damage; or
1.7.3 Operated in any way contrary to any operating or maintenance instructions; or
1.7.4 Improperly handled, installed or maintained; or
1.7.5 Altered or modified prior to or after installation; or
1.7.6 Damaged directly or indirectly by power surges, electrical storm damage or connection to incorrect
power supply
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY THE
CONSUMER MUST CALL 1300 373 199 (AUSTRALIA) OR 0508 123 108
(NEW ZEALAND) TO CONNECT TO THE NEAREST AUTHORISED CENTRE
TheAustralianConsumerLawrequirestheinclusionofthefollowingstatement
withthiswarranty:
Our goods come with guaranteed that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
1300 373 199
15

1.8 You must provide proof of your purchase of the Bellini product and the date of purchase in order to obtain
the benefit of this warranty.
1.9 If you live outside the service area of the Company or one of its service agents, this warranty does not
cover the cost of transport of the Bellini product for service nor the service agent’s traveling costs to and
from your home.
1.10 If you are required to transport the Bellini product to the Company or its service agent, you must ensure it is
safely disconnected by a qualified tradesman and securely packed and insured. The Company does not
accept any responsibility for loss or damage of the Bellini product prior to it being received by the Company
or its service agent.
1.11 You will be responsible for all costs of returning a Bellini product to the Company and for redelivery of the
Bellini product by the Company (whether it is the original or a repaired and/or a replacement Bellini product)
and for any other expenses you incur in claiming under this warranty.
1.12 The Company or its service agent will examine any Bellini product and if the Company determines that it is
defective through no fault of the Owner and is otherwise undamaged, the Company will repair or replace
the Bellini product in accordance with this warranty.
DO NOT SEND IN THIS WARRANTY
Fill out the following details and file with your purchase invoice.
RETAIN & FILE WITH YOUR RECEIPT
Your Purchase Receipt/Invoice is proof of date of purchase. If you are unable to establish the date of purchase,
or if the fault is not covered by this warranty, or if the product is found to be in working order, you will be required
to bear all service call charges.
GSM Sales Pty Ltd reserves the right to discontinue items, modify designs and change specifications without
incurring obligation.
Whilst every effort is made to ensure that descriptions, specifications and other information in this publication is
correct, no warranty is given in respect thereof and the company shall not be liable for any errors therein.
Purchased from:
Co. Name:
Address:
Date of Purchase:
Serial number:
NOTE: Consistent with our continuing product development policy, improvements may have been made
which render the contents of this packaging slightly different to that shown.
FOR WARRANTY SERVICE CALL 1300 373 199 (AUSTRALIA)
OR 0508 123 108 (NEW ZEALAND) TO CONNECT YOU TO THE NEAREST
AUTHORISED SERVICE CENTRE
16

P/N:291800201684
17