Bellman Visit 868 User manual

26
Bellman Visit 868 Repeater, BE1510
Thank you for choosing products from Bellman & Symfon.
The Bellman Visit 868 System consists of a number of radio transmitters and receivers.
The transmitters detect different events in the surrounding area and transmit a radio
signal to the receivers. The receivers pick up this signal and provide indications using
light, sound and/or vibration.
The transmitter determines what type of light, sound or vibration should be displayed so
that the reason for the indication is evident.
Read through the entire user manual rst and then start to install the system.
Refer to the illustration of the Bellman Visit 868 System on the inside of the cover.
Introduction
Getting started
Unpacking, installing and testing the unit
1. Open the battery cover (7). Connect the power supply unit to the socket (6), t one back-up
battery, either a 6LR61 alkaline or 6F22 lithium type battery, and close the battery cover.
2. Press the Test Button (2). The Bellman Visit 868 Repeater blinks with the LED (1) to indicate
that the unit is transmitting a radio signal. The Bellman Visit 868 receivers will indicate the Door
Signal.

27
General
Function
The Bellman Visit 868 Repeater, BE1510, is a repeater in the Bellman Visit 868 System for
indoor use which receives a radio signal from a transmitter in the Bellman Visit 868 System and
transmits this radio signal to the receivers in the system. The aim is to increase the range and
obtain reception in locations in which it is not otherwise possible by using Bellman Visit 868
Repeaters.
The Repeater also operates as a multi-function transmitter, either via a pushbutton or via an input
for an Exterior External Trigger. The Test Button and Exterior External Trigger can be detected
separately and transmit different Signal Patterns to the receivers in the Bellman Visit 868 System
depending on what has activated the Bellman Visit 868 Repeater. There is a range of options
for connecting the Bellman Visit 868 Repeater to various applications. We recommend using a
maximum of one Repeater per system.
CZ
DE
DK
ES
FI
FR
GB
GR
HU
IT
NL
NO
PL
PT
SE
YU
3. Mount the Bellman Visit 868 Repeater on the wall either using the self-adhesive Velcro tape
or suspended on the wallmount bracket (8) on the screw supplied. If the Velcro tape is used, the
wall on which the transmitter is to be positioned can be cleaned using the enclosed wet wipe. The
Repeater can also be placed on a level surface, e.g. a table, but avoid placing it on the oor.
Radio key
On delivery all Bellman Visit 868 units are tuned to the same Radio Key. If you have a neighbour
with a similar system, you can change to different Radio Keys so that you do not affect each
other’s systems. If you use the Radio Key Switch (5) to change the Radio Key on this transmitter,
you must also change all other units in your Bellman Visit 868 System to the same Radio Key.
Refer to the user manual for the relevant unit.

28
System indicators
The LED (1) blinks, when the Bellman Visit 868 Repeater transmits or receives radio signals.
Power supply
When the Repeater is connected to the power supply unit, the LED is constantly green, apart from
when it is receiving or transmitting radio signals when it blinks.
When the Repeater is activated, the LED (1) lights up green. This means that the back-up battery is
in good condition.
If the LED (1) blinks yellow, this means that the back-up battery is at and must be changed. Only
use a 6LR61 (alkaline) or 6F22 (lithium) type battery.
Indicators and Signals
Troubleshooting in brief
Problem
Nothing happens when the transmitter is activated
with the Test Button (2).
Solution
• Check that the power supply unit is connected
correctly.
• If the power supply unit is not connected, change
the back-up battery. Only use an alkaline 6LR61 or a
lithium 6F22 type battery.
Make sure that the power supply unit is connected
correctly.

29
CZ
DE
DK
ES
FI
FR
GB
GR
HU
IT
NL
NO
PL
PT
SE
YU
For further information about the product in English, refer to the Appendix.
1. LED. Combined transmission and back-up battery indicator. For
further information see Indicators and Signals
2. Test button/pushbutton
3. Exterior External Trigger.
4. Signal switch
5. Radio key switch
6. Connector for power supply unit
7. Battery cover
8. Wall mount bracket
The LED (1) blinks yellow when the Repeater is
activated.
The LED (1) blinks green when the Repeater is
activated, but the receivers are not signalling.
The receivers in the system transmit signals for no
reason.
• Change the back-up battery. Only use an alkaline
6LR61 or a lithium 6F22 type battery.
Make sure that the power supply unit is connected
correctly.
• Check the battery in the receiver.
• Check that the receivers are not placed too far
away by moving them closer to the transmitter.
• Check that the Repeater is set to the correct radio
key. For further information see Function/Radio
key.
• Change the Radio Key on all units in the system.
For further information see Function/Radio key