Belson Outdoors MINISAN MSN01-1000 User manual

111 North River Road
North Aurora, IL 60542
Phone: [phone]
Fax: [phone]
[email protected]
Model # MSN01-1000 Instructions Sheet
www.belson.com
MINISAN™ HAND SANITIZER DISPENSER STAND
We recommend reading through the entire assembly instructions prior to proceeding
with installation, service and maintenance. All references to left and right throughout this
guide are as viewed from the front.
DIMENSION
Height
Width
Depth
Base Capacity
Advertising Area
Weight Empty
Maximum Foam Dispensers
IMPERIAL
58
in
15 in
15 in
2.2 gal
8 x 10.5 in
8 lbs
67.5  oz
METRIC
147 cm
38 cm
38 cm
8.3 L
20.3 x 26.7 cm
3.63 kg
2000 mL
SPECIFICATIONS
Sanitizer foam dispensers not included.

www.belson.com
MSN01-0002
MiniSan
Dispenser Holder
PC-000417
3/4” Uni-Seal
MSN01-0001
MiniSan Base
FD1-1000
Foam Dispenser
or FD1-2000
Hands Free
Foam Dispenser
(Sold Separately)

www.belson.com
General Use and Information
Assembly Instructions
Step 1. Fill the MSN01-0001 base with water or sand through the hole in the
all sand in and around
the top of the post.
Step 2. Insert the PC-000417 Uni-Seal in the hole in top of the Base
Step 3. Liberally apply some dish soap or other suitable lubricant to the inner
surface of the Uni-Seal.
Step 4. Insert the stem at the bottom of the MSN01-0002 dispenser holder
rmly press the dispenser holder down onto the base until
seated.
Step 5. Mount the hand sanitizer dispenser (s) using the directions that came
t this prod-
uct. We recommend the use of either the FD1-1000 Dispenser, or the FD1-2000
Hands Free Dispenser. The use of PC-000105 rivets is recommended to mount
the dispensers.
Filling a Dispenser:
If this product is installed with the FD1-1000 or FD1-2000 foam dispensers
from PolyJohn (recommended), then push up on the tab from underneath the
dispenser and pull down the cover. Fill with Rid-It™ - Foam Hand Sanitizer
(follow the instructions located on the sticker inside of the foam dispenser). Order
lls, available from PolyJohn. If this product
is being used in a cold environment such as a winter event, please order part #
lls available from PolyJohn.
Draining the Base:
lled with water, pull up on the MSN01-0002 dispenser
holder, while holding the base down. Remove the PC-000417 Uni-Seal, and tip
the base over into a sink.

www.belson.com
CLEANING AND MAINTENANCE
Use a mild soap to clean all surfaces and component parts.
Minor scratches and abrasions can be lightly sanded or scrubbed with a mild abrasive
cleaner (such as “Soft Scrub”) that contains calcium carbonate, hypochlorate bleach and
detergents. Be sure to follow the cleaning product directions since these ingredients
may cause hazardous gases when mixed with other chemicals. Rinse the cleaned area
with a conventional wax.
Some light scratches may also be hidden by using an industrial hot air gun.
For a source of cleaning, deodorizing and paper products contact:
RID IT
2500 GASPAR AVE.
WHITING, IN
TENSION 514
www.rid-it.com
We highly recommend membership in the Portable Sanitation Association International
(PSAI); the worldwide authority on portable sanitation services. The PSAI, “Portable
cation Program” manual contains a wealth of information on
standards and service procedures. For more information contact the PSAI:
7800 METRO PARKWAY, SUITE 104
BLOOMINGTON, MINNESOTA 55425 USA
www.psai.org