Silver King SKNES2 Quick start guide

1
Technical Manual
and
Replacement Parts List
Cream Dispenser
Specifications Subject to Change Without Notice.
1600 Xenium Lane North, Minneapolis, MN 55441-3787
Phone [phone]
MODEL SKNES2

1
TECHNICAL MANUAL
MODEL SKNES2 CREAM DISPENSER
INSTALLATION, OPERATION AND MAINTENANCE
Thank you for purchasing Silver King food service equipment. Our goal is to provide our customers with the most reliable
equipment in the industry today. Please read this manual and the accompanying warranty information before operating your new
Silver King unit. Be sure to complete and mail the warranty card within 10 days of purchase to validate your warranty.
Upon delivery of your new Silver King unit, inspect the carton and unit for shipping damages. Report any damage immediately to
the transportation carrier and file a written freight damage claim to protect your investment. If a claim is to be filed, save all
packaging materials.
INSTALLATION
The stainless steel exterior of the cabinet has been protected by a plastic covering during manufacturing and shipping. This
covering can be readily peeled before installation. After removing this covering, wash the interior and exterior surfaces using a
warm mild soapy water solution and a sponge or cloth, rinse with clean water and wipe dry.
Drip Tray:
The Drip Tray and Drip Tray Cover are shipped inside the unit. Install them as shown on the replacement parts diagram found later
in this document.
Location:
When locating your cream dispenser, convenience and accessibility are important considerations, but the following factors must be
observed:
•When placing the unit on a counter, the counter must be able to support a minimum of 100 pounds.
•When placed on a counter, the unit must be on the feet supplied. If the feet are removed the unit will not operate properly
and the warranty will be void.
•There must be at least two inches of clear space above, on the sides and behind the unit and open in front.
•Correct serving height is important so that those using the dispenser can operate the dispenser properly.
•The unit must be level. The feet are adjustable to aid in leveling the unit.
•Avoid placing the unit next to an oven, heating element or hot air source which would affect the performance of the unit.
Electrical Connections:
Be sure to check the data plate, located on the liner of the cabinet, for required voltage prior to connecting the unit to power. The
specifications on the data plate supersede any future discussion.
The standard dispenser is equipped with an seven (7) foot power cord that requires a 115 Volt, 60 Cycle, 1 Phase properly
grounded electrical receptacle. The power cord comes with a 3 prong plug for grounding purposes. Any attempt to cut off the
grounding spike or to connect to an ungrounded adapter plug will void the warranty, terminate the manufacturers responsibility and
could result in serious injury.
The circuit must be protected with a 15 or 20 ampere fuse or breaker.

2
OPERATION
Initial startup:
After satisfying the installation requirements, the cream dispenser is ready to start. The unit will start when the power cord is
connected to a live electrical receptacle. If the compressor is not running when the unit is initially plugged in, check to make sure
that the Temperature Control is not set to the ‘off’ position. Allow the unit to run a minimum of two hours before loading it with
product.
Preparation For Use:
Once the unit has achieved proper operating temperature, observe the procedures noted in the label on the door liner for loading
cream into the cream dispenser. When removing an empty Cream Container, be sure to push the Valve Slide in fully before pulling
the Dispensing Tube out of the valve. It may be easier to remove or install the Dispensing Tube in the valve by removing the Valve
Insert first then removing or installing the Cream Container and Dispensing Tube. The end of the tube may need to be cleaned
daily with a clean cloth to prevent buildup which could affect the dispensing of product.
Temperature Control:
The Temperature Control is factory set at the midpoint position, which will maintain an average product temperature of around 36 -
38 Deg F.
Defrost:
The Silver King cream dispenser is a manual defrost unit. The unit should be defrosted whenever the walls accumulate a frost bank
that is 1/2 inch thick. To defrost the unit, either turn the Temperature Control knob to the ‘off’ position or disconnect the power cord
from the electrical receptacle, and open the door. After the frost has melted or come loose from the cabinet walls, wipe out the
cabinet interior. Do not attempt to scrape or chisel off the frost as you could do irreparable damage to the unit.
MAINTENANCE
Preventative maintenance is minimal although these few steps are very important to continued operation and maximizing the life of
the appliance.
Cabinet Surfaces:
The cabinet interior and exterior are stainless steel and should be cleaned periodically with a solution of warm water and a mild
soap, rinsed and wiped dry with a clean soft cloth. A stainless steel cleaner can also be used. Should a surface become stained or
discolored, do not attempt to clean with an abrasive cleaner or scouring pad. Use a soft cleaner and rub with the grain of the metal
to avoid scratching the surface. Do not use chlorinated cleaners.
Valve Assembly:
To dis-assemble the valve for cleaning start by pushing in on the Valve Slide and pulling the Valve Insert up and out. This will free
up all of the valve parts. The Valve Slide, Spring and Cap Sleeve will all be removable once the Valve Insert is removed. Clean all
valve parts with a solution of mild soap and warm water. Rinse, dry and re-assemble. The Valve Body must be cleaned in place as
it is not readily removable.
MODEL SERIAL NO. DATE INSTALLED

3

4

5
REPLACEMENT PARTS LIST – MODEL SKNES2
WHEN ORDERING REPLACEMENT PARTS, PLEASE PROVIDE MODEL AND SERIAL NUMBERS

6
FORM NO. 30931 REV I