Beltronics Shifter ZR4 User manual

Important Notes
SHIFTER ZR4 Comes Complete
 Read This First Please read both sides of
these instructions before
starting your installation.
For the easiest trouble-free
installation, install the
Interface first, and wire it to
a 12-volt switched circuit.
Then before installing the
other components, plug all
of them into the Interface
and power up the unit to
confirm proper operation.
Since Laser signals will not
pass through any objects,
including plastic, it is critical
that the Laser SHIFTERS be
mounted perfectly level, and
have an unobstructed “view”
of the road.
Performance
Warning
1 A professional installer
must install your new Laser
SHIFTER. Installation of this
system requires experience
and expertise in automotive
electronics. Car audio
specialists and many new
car dealers can install the
Laser SHIFTER for you.
2 Attempting to install this
product without expertise
in automotive electronics
installation can cause
personal injury, or damage to
your vehicle.
3 If your vehicle is
damaged during installation,
its safety systems may be
compromised, which could
cause personal injury or
property damage.
4 Improper installation
may void SHIFTER’s warranty.
Front Laser SHIFTERS
• Twin weather-proof sensors
• 16 foot cables with in-line
grommets
• Universal mounting brackets with
stainless steel hardware
Miniature
Display Controller
• Display Controller mounts easily
to instrument pod, dashboard, or
console
• Velcro and adhesive pads
provided for secure mounting
Interface
• Central module connects to
switched 12-volt power and
ground
• All components plug directly in
using modular connections
• 3M connector taps into existing
vehicle wiring
Rear Laser SHIFTER
• Weatherproof license plate
mounted sensor
• 30-foot cable with modular
connector
Documentation
• Comprehensive Owner’s Manual
• Installation Manual
Built-in Diagnostics
• Confirms all components are
operational
CINCINNATI MICROWAVE
5440 West Chester Road
West Chester OH 45069
Sales/Service 800-433-3487
LaserShifting.com
©2008 CINCINNATI MICROWAVE. SHIFTER ZR4, SPEED OF LIGHT PROTECTION and CINCINNATI MICROWAVE are trademarks of
ESCORT Inc. Features, specifications and prices subject to change without notice.
Important
Installation
Warnings
®
®
®
SP E E D O F L I G H T P R O T E C T I O N™
L A S E R D E F E N S E S Y S T E M
LA S E R SH I F T I N G TE C H N O L O G Y • P R O F E S S I O N A L I N S T A L L A T I O N
Installa tion Ma nua l

Interior of Vehicle
Radar
Detector
(Optional)
12 Volt
Power Line
±
Display Controller
SHIFTER ZR4 Installation Manual
1 Determine the best location for the
Display Controller in the vehicle’s
interior. (Consult customer if
necessary.)
2 Install Display Controller using
supplied velcro, or double-sided tape.
3 Route cable and plug into jack
marked “Display” on Interface.
Note:
1. Make certain that the Display is
clearly visible from the driver’s
position, and that the controls can be
easily accessed without
interfering with normal driving.
A
E
C
B
B
D
D
F
A
G
BB
1 Remove two license plate screws
(top or bottom).
2 Mount Laser SHIFTER to plate using
supplied mounting bracket.
3 Route wire through trunk
compartment, and into the vehicle’s
interior.
4 Insert connector to jack labeled
“Rear Shifter” on Interface.
Tips
1. Do not block license plate
illumination.
2. Do not cover any required license
plate information.
Installation Alternatives:
1. Cable can be routed under vehicle
(keep away from hot and moving
parts) then brought into the vehicle’s
interior.
2. DO NOT SPLICE CABLE unless
within interior of vehicle. Reconnect
and solder each of the three wires,
and seal with heat-shrink tubing.
1 Determine best location for the
Laser SHIFTERS. For optimum
performance, install each laser
SHIFTER on either side of the front
license plate, with a clear “view” of
the road. If possible, center each
SHIFTER module between the license
plate, and the outside edge of the
vehicle. (See photo below at left.)
2 Determine which mounting
hardware (metal U-bracket or grill
clamp) is best suited to the vehicle.
Mount the front SHIFTERS to a sturdy
part of the grill or bumper. To tighten
the grill clamp, simply insert a 9/64
Allen wrench into the front slot of the
clamp. (See illustration below.)
3 Before tightening, pull SHIFTER
cables through grill area and make
Front Laser SHIFTERS Rear Laser SHIFTER
After all components are installed
correctly:
1 Turn the Laser SHIFTER on by
rotating the volume control knob.
2 Turn vehicle’s ignition to the “on”
position.
3 SHIFTER will cycle through a
startup sequence.
Test
Radar Detector (optional)
CB
1 Determine best location for your
detector.
2 Route optional “link” cable to the
ZR4 interface and plug into “detector”
jack.
3 Connect the other end of the cable
to the actual detector.
4 Refer to the Owner’s Manual for
programming options.
Interface Remote Mute Laser SHIFTER Cables
D E G F
1 Install Interface under the dash
using supplied zip-ties. DO NOT
MOUNT IN ENGINE COMPARTMENT.
2 Connect black wire (–) to ground,
and red-striped wire (+) to a switched
12-volt supply. (If the Laser SHIFTER
is left in the “on” position, it will
automatically power on and off with
the ignition.) Use blue 3M connector
(provided) to tap into existing circuit
if needed.
3 Be sure to plug all cables into the
correct labeled jacks.
1 Determine best location for the
Remote Mute Button.
2 Clean surface area.
3 Remove paper backing on the back
of the button, and press onto surface.
4 Route cable and plug into jack
marked “Mute” on Interface.
1 Route Laser SHIFTER cables to
firewall, and secure with zip-ties
(included).
2 Route both SHIFTER cables into the
vehicle’s interior. If there is not a
suitable opening, drill a 13/32" or
7/16" hole.
3 Pull cables through firewall, and
plug into jacks marked Front Shifter 1
and Front Shifter 2 on interface.
4 Pull grommet (located on each
cable) through the firewall to seal the
hole. Use silicone sealant (not
supplied) if necessary.
Note:
1. Only drill hole in firewall after
thoroughly investigating location first,
ensuring no other wires, hoses, etc.
will be damaged.
2. Keep all cables away from moving
parts, and hot surfaces. (Radiator,
hoses, etc.)
3. DO NOT SPLICE CABLE unless
within interior of vehicle. Reconnect
and solder each of the three wires,
and seal with heat-shrink tubing.
certain that both SHIFTERS (front
lens) are level to the road. THEY
MUST BE LEVEL TO WORK PROPERLY.
Note:
1. Thoroughly investigate location of
SHIFTERS and cables before installing.
2. Keep cables completely away from
all moving parts and hot surfaces in
the engine compartment.
3. DO NOT SPLICE CABLE unless
within interior of vehicle.
4. Double-check to make certain the
SHIFTERS are level and have a clear
view of the road.
Grill Clamp