BENRO DJ Series User manual

DJ Series Tilthead
75 Virginia Road
North White Plains, NY 10603
T 914.347.3300
F 914.347.3309
[email protected]
BenroUSA.com
Operating Instructions
Thank you for making Benro your choice for professional photographic
equipment. Your Benro gear is manufactured to provide years of
dependable service. In order to obtain optimum satisfaction and
performance, we suggest that you carefully read these instructions.
Specifications and design are subject
to change without notice.

Bubble Level
Quick Release Plate
Tilt Lock Knob
Security
Locking Lever
Plate Locking Lever
SETUP
Head Mounting
Install by screwing the head clockwise onto
the 3/8" mounting thread of the top plate
of the Monopod. Once it is hand tight, if
available, secure by fully tightening the
Head Locking Screw(s) (on select models)
from below.
OPERATION
Positioning Adjustments (FIGURE 1)
Horizontal rotation or panning can be
easily accomplished by swiveling the
entire Monopod.
Front to rear angle or tilt adjustments can
be easily accomplished by first loosening
the Tilt Lock Knob (be sure to hold firmly to
balance weight of the camera). Position as
desired and tighten the Knob securely.
Depending on your requirements, you may
find it convenient to reorient the camera or
lens 90° on the Quick Release Plate and then
remount. This allows the Tilt Control Knob
to give you different positioning support.
NOTE: Do not over tighten the Locking
Knob as this could damage the Tilthead
locking mechanism.
Quick Release Plate
The DJ Series Tilthead incorporates a Quick
Release Plate system. It offers a quick
method of mounting or releasing a Camera
or Equipment from the Head. It’s important
that the correct Quick Release Plate be used
along with the proper mounting screw
(1/4–20 is included as the standard size but
spare 1/4–20 and 3/8 plates are available as
accessories). Extra Plates are recommended
as you can screw one to each Camera or
Lens for even greater convenience when
rapidly mounting and dismounting gear.
Quick Release Locking Lever
(FIGURES 2, 3 & 4)
When used properly, the patented Dual
Lock Quick Release system offers two levels
of security for your gear. To remove the
Quick Release Plate, squeeze both the Plate
Locking Lever and the Security Locking
Lever and pull the larger Locking Lever
out. The Quick Release Plate will disengage
allowing it to be removed.
To reconnect the Quick Release Plate, insert
the angled part of the Plate into the groove
on the opposite side of the Locking Levers
and press down flat. The Locking Levers will
automatically engage the locking system and
will return to the safety lock position. Press
the Plate Locking Lever in firmly to secure.
USER NOTICE
• Do not exceed the maximum specified
load capacity (see specifications at
www.BenroUSA.com).
• Always ensure that all Tilthead locks
are tightly engaged before mounting
any gear.
• Always clean and dry any Tilthead after
it has been exposed to wet, dusty, sandy
or salty conditions. Your Tilthead is not
recommended for use in salt water. If
required, clean ballhead using a mild
soap solution applied with a soft cloth,
rinse with fresh water and dry with soft
towel. Remove any dust, dirt or sand from
all locks and all moving parts.
• Do not leave any Tilthead in the sun
for prolonged periods and avoid high
temperature exposure.
• Avoid leaving any Tripod or Monopod
unattended in areas where people could
trip over the gear and get hurt.
• Remove camera, lens, and all gear from any
Tripod or Monopod when transporting.
• For your safety, don’t let your Benro
gear come in contact with any electrical
power source.
1
3
2
4
Operating Instructions & User Notice