Besenzoni BUC User manual

Download
Besenzoni Control Device
from the APP Store
With you can use your smartphone
to manage the handling of hydraulic gangway
Besenzoni installed on board through
bluetooth technology.
Download the Besenzoni Control Device App
from the App store, check that your device
is compatible with the operating systems
that allow the App to work:
IOS .0 or later
Android 7.0 or later
WHITE VERSION
Watch
video
I0

Garanzia:
Besenzoni fornisce una garanzia sul prodotto in conformità della normativa vigente.
In casi di disputa: a) per clienti italiani sarà competente l’Autorità giuridica italiana
in particolare il foro di Bergamo. b) per cliente esteri si ritiene competente l’arbitrato
della Camera di Commercio Internazionale.
Important information:
Before positioning, installing and commissioning the device, read this instruction manual
carefully as it contains important information on assembly, safety and use.
Do not change or tamper with any part of the device.
Improper use could harm people and/or objects.
Besenzoni S.p.A. cannot be held responsible for damages caused by failure to follow these
instructions. Keep these user instructions safe and pass them on to any future users.
Only a specialised technician may install the Besenzoni Unit Control
contained in this box. You may find it useful to check the “Assistance and Resellers”
section in the Besenzoni Control Device App, which includes a map
of our official Service points that you can contact.
This box contains:
A1 - Besenzoni Unit Control.
Bluetooth Receiver / Adaptor code 7FF99620 to be used
with up to 8 smartphones/devices.
B1 connector cable for the 4 button control panel
to control the transom passerelle.
C1 connector cable for the 6 button control panel
to control the retractable passerelle.
The instructions for installation and use in Italian and English are available on:
www.besenzoni.it/landing/buc
INSTRUCTIONS FOR INSTALLATION AND USE

BOX 100x100
GANGWAY ELECTRONIC
JUNCTION BOX
Inside: DIP-switch for 4 or 6 button
control panel
DIP = ON 4 buttons
DIP = OFF 6 buttons
Option 1
Button control panel
to control a transom passerelle
Option 2
Button control panel
to control a retractable passerelle
Connect cable for 4 button panel
Connect cable for 6 button panel
+12V o 24V
blue LED
+12V o 24V
Connect cable B or C according
to either an external or retractable
walkway in the panel cable input
A
D
E F
C
B

Remove the power source from the system that controls the passerelle.
Install the receiver/adaptor far away from heat sources and electromagnetic disturbances.
Select the appropriate connector cable out of the two that are supplied (see figs. Band C),
based on whether the boat is fitted with a transom or retractable passerelle:
Option 1: to control a transom passerelle connected to a 4 button control panel
(see
fi g . E) you must use the connector cable shown in fi g . Bwith 4 PINs.
The Bluetooth Receiver / Adaptor must be open and the DIP switch must be turned ON.
Option 2: to control a retractable passerelle connected to a 6 button control panel
(see
fi g . F) you must use the connector cable shown in fi g . Cwith 6 PINs.
The Bluetooth Receiver / Adapter has the DIP-switch default to OFF .
Disconnect the cable connected to the control panel from the electronic junction box
(see fi g . D) and connect it directly to the (see fi g . A).
Take the connector fi g . Bor C, connect it first to the and then to the control panel
socket with the same number of PINs (4 or 6) inside the electronic control unit (fi g . D).
Take note of the password on the label attached to the front of the
Power the circuit board with the electronic junction
box line stabilised at 12/24 volts.
Restore power to the system.
Activate the device’s bluetooth.
Open the App on your device.
Click Settings from the dropdown menu in the top
left-hand corner.
Choose and set an unlock code which
you will also use in the future.
Deactivate the Demo mode and tick “Start in Command View”.
Click “Set Device Code” and insert the 5 digit security code
shown on the label.
Click “Select device” and select the device that corresponds to the name shown
on the label: e.g. Name: Besenzoni1006.
Click the Dropdown menu button.
Click Command and then the screen to start the App.
The commands to control the passerelle will appear in the next screen.
In order to correctly control the passerelle, you must press and hold the selected
command, otherwise an Error message will show up on the device’s screen.
To restart the controlling operation, press and hold the command again.
INSTALLATION PROCEDURE ACTIVATION PROCEDURE
NOTE SETTINGS
Settings: by selecting Launch Commands when you next open the App, once you have
inserted your unlock code, you will have immediate access to the commands section.
Controlling the passerelle via the App still allows you to use the remote control that
you have been supplied with.
PROCEDURE FOR RESETTING MEMORIZED DEVICES:
1) Open the lid of the by removing the 4 screws
2) Press the S1 button indicated in the image for 2 seconds
until the blue LED goes out
3) Close the receiver cover. S1
blue LED

BESENZONI S.p.A.
Via Molere 2 - 24067 Sarnico (BG) Italy
Ph. [phone] r.a. | Fax [phone]
[email protected] | www.besenzoni.it
WARRANTY
Besenzoni provides a warranty for the product in compliance with the legislation in force. In case of dispute:
a) for Italian customers, the Italian law will apply and the Court of Bergamo will be competent.
b) for customers outside Italy the arbitrators of the International Chamber of Commerce will be competent.
WHITE VERSION