Bestway 58517 User manual

OWNER’S MANUAL
bestwaycorp.com/support
Visit Bestway YouTube channel
WE SUGGEST NOT TO RETURN
THE PRODUCT TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
For FAQ, Manuals, Videos Or
Spare Parts, Please Visit
bestwaycorp.com/support
V
i
s
i
t
w
w
w
.
b
e
s
t
w
a
y
c
o
r
p
.
c
o
m
/
s
u
p
p
o
r
t
f
o
r
h
e
l
p
58517

IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
• The appliance must be supplied through a residual current device (RCD) having a rated
residual operating current not exceeding 30mA.
• Ensure the transformer is at least 2 meters away from pool. Keep distance as far as
possible.
• The plug of the transformer must be at least 3.5m away from the pool.
• The appliance is only to be used with the provided transformer.
• Do not sit, straddle, step on or exert pressure on the product as injury could occur.
• DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge
trimmers, or any other equipment.
• To reduce the risk of electric shock, replace damaged cord immediately.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
• Extension cords can’t be used.
• Always unplug this product from the electrical outlet before removing, cleaning, servicing
or making any adjustment to the product.
• Don’t plug or unplug the appliance if hand is wet.
• Read the instructions before using the appliance, installing it, or reassembling it.
• If instructions are misplaced, please contact with Bestway or search it on the website:
www.bestwaycorp.com
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they do
not play with the appliance.
• This product is not intended for commercial use.
• The battery is non-replaceable.
• Non-rechargeable batteries are not to be recharged.
• Exhausted batteries are to be removed from this product. Do not dispose of product and
its batteries in fire. Check your local regulations for proper disposal instructions.
• Keep the batteries away from children.
• The battery can cause severe or fatal injuries in 2 hours or less if it is
swallowed or placed inside any part of the body.
• Medical attention should be sought immediately if it is suspected the
battery has been swallowed or placed inside any part of the body.
• If you suspect your child has swallowed or inserted a button battery
immediately call the 24-hour Poisons Information Centre on 13 11 26 for
fast, expert advice.
• Examine devices and make sure the battery compartment is correctly
secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if
SWIM FITNESS SYSTEM
OWNER’S MANUAL
3
WARNING

compartment is not secure.
• Dispose of used button batteries immediately and safely. Flat batteries can still be
dangerous.
• Tell others about the risk associated with button batteries and how to keep their children
safe.
4
TECHNICAL SPECIFICATIONS
USE THE PRODUCT
PARTS LIST
Suitable for in-ground pools or above ground metal frame pools (Pool size: length≥4.57 m(15’), width≥2.44 m(8’), depth≥1 m(39.5”))
Suggested water temperature range: 15-35°C
Frequency band: 433.92 MHz
Maximum radio-frequency power: 8 dBm
No.
1
2
3
4
5
6
Item
P05264
P05263
P04876
P04755
P04756
P04757
Description
Remote control
Swim fitness system
Transformer
Mounting bracket
Screws
Set screw
QTY
1
1
1
1
2
1
2
0.74
0.81
3
0.83
0.91
4
0.92
1.01
5
1.01
1.10
6
1.10
1.20
7
1.19
1.30
8
1.30
1.42
INTENSITY LEVEL
m/s
yd/s
1
0.65
0.71
1
3
4
5
6
2
Speed range (Approximate):
Display Panel Function:
A Digital display window
Display current mode parameters
B Calorie counter mode
1. Press this button in free running mode, the digital screen
displays the calorie interface
2. Press and hold this button in any state to enter the
calorie consumption mode setting interface, and the
calorie consumption mode button indicator will flash.
Press the “+/-” button to set the parameter increase or
decrease (range 10-1000 cal). After the setting is
completed, press the start button to start the
operation.
C Timer mode
1. Press this button in free running mode, the digital screen
displays the time interface
2. Press and hold this button in any state to enter the
timing mode setting interface, and the timing mode A B
C D E F button indicator will flash. Press the “+/-” button
to set the parameter increase or decrease (range 5-90 minutes). After the setting is completed, press the start button to start
the operation.
J I H G
A B C D E F
Disposal
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.

D Distance mode
1. Press this button in free running mode, the digital screen displays the distance interface
2. Press and hold this button in any state to enter the distance mode setting interface, and the m/yd indicator will flash. Press the
“+/-” button to set the parameter increase or decrease (range 10-5000 m/10-5500 yards). After the setting is completed, press
the start button to start the operation. (Pressing this button without holding it down will switch between m/yd units)
E Stop button
1. In all cases except the standby state, press the stop button to clear the current data and the machine will enter the standby
state.
2. When the fault code is reported, press this button to cancel the fault and the machine enters the standby state.
F Speed and parameters adjustment buttons
During operation, you can accelerate or decelerate by pressing the “+/-” key; in the mode setting, you can set the parameter to
increase or decrease by pressing the “+/-” key.
G Start/pause button
1. Press this button in the standby mode to enter the free mode, and press this button to pause during operation. The machine will
stop automatically after a maximum of 90 minutes of operation.
2. After the calorie consumption, timing or distance mode setting is completed, press this button to start running. Press this button
to pause during operation.
H LED light switch button
Press to turn on/off the LED light
I Distance unit indicator
m/yd indicator
J Speed Setting Display
One speed bar represents one speed setting, which is represented from left to right with green representing slower speeds and red
representing faster speeds. The default speed when the machine is activated is set at 4 speed bars.
5
A
B C
D
Remote control:
A Indicator light
Flashes a red color when a button is pressed
B Speed Adjustment Buttons
Press to increase or decrease the speed setting
C Emergency stop button
In an emergency, press the emergency stop switch to completely cut off the power to the
device.
D Start/pause button
Press to start or pause
If the remote control or the body of the Swimfinity is replaced, they must be paired again using the following instructions:
1. Ensure the body of the Swimfinity is in standby mode
2. The remote control must be within 3 m (10 ft.) from the control panel
3. On the remote control, press the and emergency stop button at the same time.
Hold it until you hear the buzzer sound. This means the pairing was successful.
Important: after the paring operation is finished, the alarm will appear on the control panel. This is normal. Press the stop
button on the control panel to reset the alarm, and you may use your Swimfinity.
Please disassemble and store the product indoors when the device will not be used for a
long period of time.
1. Turn off the transformer and unplug the power cable from the electrical outlet.
2. Disconnect the machine power cable from the transformer.
3. Remove the machine from the pool, and air-dry thoroughly .
MAINTENANCE

4. Store the machine and transformer in a dry place. The storage’s temperature should be
between 4°C and 40°C.
6
TROUBLESHOOTING
ERROR CODES
Alarms
Fault alarm code Problem Solution
After the remote control emergency stop button is
pressed, the system is forced to enter the fault mode.
The motor stops running and the alarm prompts.
Motor idling and overload protection. If the motor is
no-load rotating or stalling, the operation current is too
large. The system enters the failure mode, the motor
stops running and the alarm prompts.
Motor failure.
Motor temperature is too high.
Signal problem between the control panel and PCB.
Input voltage is too low.
You can press the stop button to cancel the
fault or the system needs to be powered off
and turned back on to solve the fault.
Please check if the water level in the
swimming pool is lower than the bottom of
the motor impeller or if the motor impeller is
blocked.
Turn off the power, and restart after 30
minutes or after the water temperature has
cooled.
For assistance, please visit the support
section on our website,
www.bestwaycorp.com.
For assistance, please visit the support
section on our website,
www.bestwaycorp.com.
Please check if the voltage is within the
range required by the rating label.
PROBLEM
Remote Control is no
longer working
Too noisy / Jet water
is weak
No LED display
CAUSE
- The battery is on low power.
- The machine unit is not fully immersed in the
water.
- The machine is not parallel to the water
surface.
- Motor doesn't work properly
- The transformer is unplugged or off.
- The transformer is not connected with the
machine.
- Display panel cord or display panel failure.
SOLUTION
- Contact your local Bestway Service Center for
instructions.
- Make sure the device is under the water.
- Check if the support plate is in place. Refer to
the “Installation” for details.
For assistance, please visit the support section on
our website, www.bestwaycorp.com.
- Ensure the transformer is plugged in and
switched on.
- Connect the transformer with the machine.
For assistance, please visit the support section on
our website, www.bestwaycorp.com.

7
INSTALLATION
(Pool must be filled with water before installation. Two adults required for both above and in-ground pools.)
1 2
3
x2
x2
A
4 5
x2

8
67
>2m
A. For above ground metal frame pool:
1. Pull the fastening nut out ,and remove the mounting bracket.
2. Lift the machine up to the pool frame.
3. Pull back the support plate, place it against the wall of the pool, and adjust it so the plate is placed securely against the pool
wall.
4. Grab the height adjustment handles on both sides of the machine to raise or lower the motor underwater.
5. Adjust the machine slightly to make it horizontal against the water line.
6. Tighten the locking screw.
1
140mm
160mm
B
23
x2 x2

9
45
x2
>2m
6
B. For in-ground pool:
1. Install the in-ground pool mounting bracket.
- Make sure the top surface of the pool edge is stable, flat and level.
- Drill two holes on the pool edge – in the center of the shorter side – where the mounting bracket will be installed. Pay attention to
the electrical, gas and water lines when drilling the holes.
2. Place the machine on the mounting unit.
3. Pull back the support plate, place it against the wall of the pool, and adjust it so the plate is placed securely against the pool wall.
4. Grab the height adjustment handles on both sides of the machine to raise or lower the motor underwater.
5. Use the set screw for enhanced stability.
Transformer assembly:
1. The transformer must be installed on a solid level area.
2. The transformer requires free circulation of air for cooling.
3. The transformer must be installed in a location protected from the moisture, rain
and splashing water.
Connecting the swimming machine unit to the transformer:
1. Be sure the transformer switch is OFF, and connect the transformer cable to a
grounded electrical outlet.
2. The transformer shall be placed at least 2m away from the pool. Connect the machine power cable plug to the transformer power
receptacle. Be sure the plug cover is securely tightened.
3. Turn the transformer switch ON.
440mm
240mm
8mm

303021272185
For support please visit us at:
bestwaycorp.com/support
©2021 Bestway Inflatables & Material Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte vorbehalten/Tutti i diritti riservati
Trademarks used in some countries under license from/
Marques utilisées dans certains pays sous la licence de/
Marcas comerciales utilizadas en algunos países bajo la licencia de/
Die Warenzeichen werden in einigen Ländern verwendet unter Lizenz der/
Marchi utilizzati in alcuni paesi concessi in licenza a
Bestway Inflatables & Material Corp., Shanghai, China
Manufactured, distributed and represented in the European Union by/
Fabriqués, distribués et représentés dans l’Union Européenne par/Fabricado, distribuido y representado en la Unión Europea por/
Hergestellt, vertrieben und in der Europäischen Union vertreten von/Prodotto, distribuito e rappresentato nell'Unione Europea da
Bestway (Europe) S.r.l., Via Resistenza, 5, 20098 San Giuliano Milanese (Milano), Italy
Distributed in Latin America by/Distribué en Amérique latine par/Distribuido en Latinoamérica por/Distribuído na América Latina por
Bestway Central & South America Ltda, Salar Ascotan 1282, Parque Enea, Pudahuel, Santiago, Chile
Distributed in Australia & New Zealand by Bestway Australia Pty Ltd, Unit 2/98-104 Carnarvon St Silverwater, NSW 2128, Australia
Tel: Australia: ([phone]; New Zealand: 0800 142 101
Distributed in United Kingdom by Bestway Corp UK Ltd. 8 Wentworth Road, Heathfield Industrial Estate, Newton Abbot, Devon, TQ12 6TL
Exported by/Exporté par/Exportado por/Exportiert von/Esportato da
Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited
Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong
Tel: [phone] (For U.S. and Canada)
www.bestwaycorp.com