beta sensorik MW SDR-75 Series User manual

beta SENSORIK GmbH · Hummendorfer Straße 74 · 96317 Kronach · Telefon [phone] · Fax [phone]
[email protected] · www.betasensorik.de
!!!!!!!!!!!!!!!!!!!!!!!!!!!Installation Manual
zType烉
烉
SDR DIN rail power supply
炷
炷
Series烉
烉
SDR-75, SDR-120, SDR-240, SDR-480, SDR-480P, SDR-960炸
炸
SDR-75-12 INPUT: 100-240VAC 1.55A 50/60Hz OUTPUT: 12V 6.3A
SDR-75-24 INPUT: 100-240VAC 1.55A 50/60Hz OUTPUT: 24V 3.2A
SDR-75-48 INPUT: 100-240VAC 1.55A 50/60Hz OUTPUT: 48V 1.6A
SDR-120-12 INPUT: 100-240VAC 1.4A 50/60Hz OUTPUT: 12V 10A
SDR-120-24 INPUT: 100-240VAC 1.4A 50/60Hz OUTPUT: 24V 5A
SDR-120-48 INPUT: 100-240VAC 1.4A 50/60Hz OUTPUT: 48V 2.5A
SDR-240-24 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 24V 10A
SDR-240-48 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 48V 5A
SDR-480-24 INPUT: 100-240VAC 5A 50/60Hz OUTPUT: 24V 20A
SDR-480-48 INPUT: 100-240VAC 5A 50/60Hz OUTPUT: 48V 10A
SDR-480P-24 INPUT: 100-240VAC 5A 50/60Hz OUTPUT: 24V 20A
SDR-480P-48 INPUT: 100-240VAC 5A 50/60Hz OUTPUT: 48V 10A
SDR-960-24 INPUT: 200-240VAC 6A 50/60Hz OUTPUT: 24V 40A
SDR-960-48 INPUT: 200-240VAC 6A 50/60Hz OUTPUT: 48V 20A
zIntroduction
SDR is a DIN rail power supply series with a 150% peak load capability (3 seconds) and high efficiency of up to 94%.
Like other Mean Well’s DIN series, they can be mounted on a TS35 Standard DIN rail.
zInstallation
炷1炸Always allow good ventilation clearances, 5mm left and right, 40mm above and 20mm below, around the unit
in use to prevent it from overheating. Also a 10-15 cm clearance must be kept when the adjacent device is a
heat source.
炷2炸The appropriate mounting orientation for the unit is vertical, the input terminals at the bottom and output on
the top. Mounting orientations other than that, such as upside down, horizontal, or table-top mounting, is not
allowed.
beta
SENSORIK

beta SENSORIK GmbH · Hummendorfer Straße 74 · 96317 Kronach · Telefon [phone] · Fax [phone]
[email protected] · www.betasensorik.de
3
1
2
4
炷3炸Use copper wire only, and recommended wires are shown as below.
AWG
18
16
14
12
10
Rated Current of
Equipment (Amp)
6A 6-10A 13-16A 16-25A 25-32A
Cross-section of
Lead(mm
2
)
0.75 1.00 1.5 2.5 4
Note: 1. Current each wire carries should be de-rated to 80% of the current suggested
above when using 5 or more wires connected to the unit.
2. The maximum allowable wire cross-sectional area for the terminal of the
SDR-75 is 12AWG/2.5 mm2 .
Make sure that all strands of each stranded wire enter the terminal connection and the screw terminals are
securely fixed to prevent poor contact. If the power supply possesses multi-output terminals, please make
sure each contact is connected to wires to prevent too much current stress on a single contact.
炷4炸Use wires that can withstand temperatures of at least 80°C, such as UL1007.
炷5炸Recommended wire strapping length is 5mm (0.197”).
炷6炸Recommended screwdriver is 4mm, slotted type.
炷7炸The recommended torque setting for terminals is shown as below.
Model
I/P
O/P
SDR-75
4 kgf-cm (3.5 Lb-in)
4 kgf-cm (3.5 Lb-in)
SDR-120
6.3 kgf-cm (5.5 Lb-in)
8 kgf-cm (7 Lb-in)
SDR-240/480/480P
5 kgf-cm (4.4 Lb-in)
8 kgf-cm (7 Lb-in)
SDR-960
10 kgf-cm (9 Lb-in)
8 kgf-cm (7 Lb-in)
炷8炸Suggested fuse and maximum number of the SDR PSUs that can be connected to a circuit breaker at 230V are
shown as below.
Model Fuse
Circuit breaker
C16
D16
SDR-75
T3.15A/L250V
10
12
SDR-120
T4A/L250V
7
14
SDR-240
T5A/L250V
4
8
SDR-480
T8A/L250V
4
4
SDR-480P
T8A/L250V
4
4
SDR-960
F10A/H250V
2
2
炷9炸Mounting Instruction烉
Mount as shown in figure only, with input terminals down, or else sufficient cooling will not be possible.
Admissible DIN railǺTS35/7.5 or TS35/15
For rail fasteningǺ
ȐaȑTilt the unit slightly rearwards.
ȐbȑFit the unit over top hat rail.
ȐcȑSlide it downward until it hits the stop.
ȐdȑPress against the bottom for locking.
ȐeȑShake the unit slightly to check the locking action.
"Click"
!!!!!!!!!!!!!!!!!!!!!!!!!!!Installation Manual
beta
SENSORIK

!!!!!!!!!!!!!!!!!!!!!!!!!!!Installation Manual
炷10炸For SDR-960, if it is necessary for your system to meet EN61204-3 Radiation class B. Then, attaching a ferrite
core clamp filter to the AC cable, as close as possible to the AC source, can fulfil the radiated emissions
requirements. The wiring is shown below. There are compatible models including ZCAT2235-1030A by TDK,
ZCAT12V-BK by TDK and KCF-130-B by KING CORE.
炷11炸For other information about the products, please refer to www.meanwell.com for details.
zWarning / Caution !!
炷1炸Risk of electrical shock and energy hazard. All failure should be examined by a qualified technician. Please do
not remove the case of the power supply by yourself!
炷2炸Risk of electric arcs and electric shock (danger to life). Connecting both the primary and the secondary sides
together is not allowed.
炷3炸Risk of burn hazard. Do not touch the unit in operation and shortly after disconnection!
炷4炸Risk of fire and short circuit. The openings should be protected from foreign objects or dripping liquids.
炷5炸Only install the unit in a pollution degree 2 environment (Note.1).
炷6炸Please do not install the unit in places with high moisture or near the water.
炷7炸The maximum operating temperature is 50°C for SDR-960 series and 60°C for SDR-75/120/240/480/480P
series, please do not install the unit in places with high ambient temperature or near fire source.
炷8炸The FG ( ) must be connected to PE (Protective Earth).
炷9炸Output current and output wattage must not exceed the rated value on its specification.
炷10炸SDR-960 is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
炷11炸Disconnect system from supply voltage:
Before commencing any installation, maintenance or modification work: Disconnect your system from
supply voltage. Make sure that inadvertent connection in circuit will be impossible!
炷12炸For continued protection against risk of fire, replace only with same type and rating of fuse.
Pour ne pas compromettre la protection contre les risqué d’incendie, remplacer par un fusible de même
type et de memes caractéristiques nominales.
Note.1: Pollution Degree 2 applies where there is only non-conductive pollution that might temporarily become
conductive due to occasional condensation. Generally refer to dry, well-ventilated locations, such as
control cabinets.
AC/N
AC/L
FG
AC
DC
CB
LIVE
NEUTRAL
PE
Clamp Filter
beta SENSORIK GmbH · Hummendorfer Straße 74 · 96317 Kronach · Telefon [phone] · Fax [phone]
[email protected] · www.betasensorik.de
beta
SENSORIK

!!!!!!!!!!!!!!!!!!!!!!!!!!!Installation Manual
Manufacturer烉
烉
MEAN WELL ENTERPRISES Co., LTD.
No.28, Wuquan 3rd Rd., Wugu Dist.,
New Taipei City 24891, Taiwan
Tel: [phone]
Web: www.meanwell.com
beta SENSORIK GmbH · Hummendorfer Straße 74 · 96317 Kronach · Telefon [phone] · Fax [phone]
[email protected] · www.betasensorik.de
beta
SENSORIK

beta SENSORIK GmbH · Hummendorfer Straße 74 · 96317 Kronach · Telefon [phone] · Fax [phone]
[email protected] · www.betasensorik.de
Declaration of China RoHS Conformity
In order to reduce the impacts on the environment and take the more responsibility for protecting the
earth, MEAN WELL is confirming and announcing the conformity to China RoHS, an
Administrative Measures for the Restriction of the Use of Hazardous Substances in Electrical and
Electronic Products.
Environment Friendly Use Period Label
Observing SJT 11364-2014, Marking for the Restricted Use of Hazardous
Substances in Electronic and Electrical Products
Observing SJ/Z 11388-2009, General Guidelines of Environment-friendly
Use Period of Electronic Information Products Appendix B, adopting
table look-up to verify the Environment Friendly Use Period
Names and Contents of Hazardous Substances Lists
Part Name
Hazardous Substances
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
chromium
(Cr
6+
)
Polybrominated
biphenyls
(PBB)
Polybrominated
diphenyl ethers
(PBDE)
PCB and its
components
X
O X O O
O
Metal structure
parts
X
O O O O O
Plastic structure
parts
O
O O O O O
Accessories
O
O
O
O
O
O
Cables
X
O
O
O
O
O
O: The concentration of the hazardous substances within the homogeneous material of that product is less than
the concentration limits set by GB/T 26572-2011.
X: The concentration of the hazardous substances within the homogeneous material of that product is over the
concentration limits set by GB/T 26572-2011; however, it follows the standard advised by 2011/65/EU.
beta
SENSORIK