BHG BH15-092-099-01 User manual

1
BHG Sullivan Pointe 3 person Gazebo Swing
ASSEMBLY INSTRUCTIONS
ITEM# BH15-092-099-01
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
Questions, problems, missing parts with this product? Do not return to your
retailer,please call our customer service department 9:00 a.m. to 5:00 p.m.
Eastern Standard Time Monday through Friday Phone # [phone]
contact us at www.numarkcustomerservice.com
DON’T RETURN TO STORE
or

2
WARNINGS AND CAUTIONS
CLEANING AND MAINTENANCE
Pls inspect and tighten all bolts or fasteners on a regular basis to ensure proper
performance and safety of your swing.
＊Wash frame and fabric with mild soap and water; rinse thoroughly.
Dry frame completely and allow the fabric to drip dry away from direct sunlight.
Do not use bleach, acid, or other solvents on the fabric or frame parts.
DON’T RETURN TO STORE
In order to prolong the life and beauty of your swing, we recommend that the swing be
stored in a dry area when not in use. (For example, overnight or on rainy days.)
＊It is essential to place the swing on level ground and not less than 1.83m
from any obstruction such as fences, garages, the house, overhanging
branches, laundry lines, or electrical wires.
＊
Assembly by four adults is recommended.
＊Always remove the canopy in heavy wind conditions, otherwise the canopy
may tip over and may cause damage to its parts.
＊The swing should always be inspected before each use.
＊Do not discard any of the packaging until you have checked that you have
all the parts and pack of fittings.
＊
Keep children away during assembly.This item contains small parts which
can be swallowed by children.Children should always be under direct adult
supervision while using the product.
＊The manufacturer will not accept responsibly for unauthorized repair of
modifications to the gazebo.
Retain the assembly instructions for future reference.
Oil all metallic moving parts during usage season
Check all nuts and bolts for tightness before and during usage season.
＊
＊
＊
＊
＊
＊
＊
＊Weight limit 600lbs.

Remove all components from the polybag and unwrap all package materials. Please
count the components, there are:
NO.
Part
Description
Quantity
A
B
Side Panels
2
C1
1
G
2
H
1
E
1
F
1
I
4
Leg Post
Right Arm
J
2
Long Hanging Bar
3
Top Crossbar
Rear Leg Crossbar
Left Arm
Seat Support Bar
Seat and Back
D
4
4
K
L
M
N
O
P
1
1
2
1
Pillows
Short Hanging Bar
Canopy Side Bar
Canopy Top Frame
Cushion
Canopy Fabric
DON’T RETURN TO STORE
A
C
2
Q
R
S
Leg Post 2
2
4
2
Top Crossbar
Post Base
Base Plate

4
DON’T RETURN TO STORE
I
P
J
R
S
T14
A
B
C
D
E
F
G
H
Q
E
KLK
L
K
P
I
M N
N
N
N
D
O
T13

5
NO.
Part
Description
Quantity
T1
M6x12L
8+1 spare
T2
M6x15L Bolt
4
T3
M6x36L Bolt
12+1 spare
T4
M6x55L Bolt
2
T5
M6 Nut
6
T6
4
T7
24
T10
2
T12
ACCESSERIES
2
T13
5
T15
1
T16
T17
1
M8x20L Bolt
M8x65L Bolt
M8x77L Bolt 2
M8 Nut
Assembly
instructions sheet
Plastic Washer
S-Hook
U-Bracket
Open Hex WrenchOpen Hex Wrench
DON’T RETURN TO STORE
2
Counter Sink Bolt
T8
T9
T11
T14
T18
4
4
6
22
4
1
2
M6 Metal Washer
M8 Metal Washer
Allen Wrench
M8 Hex Wrench

Step1
T5 x 8 T11 x 8
Please don’t tighten the bolts fully at this step.
M8 Metal Washer
M8x20L Bolt
M6x15L Bolt
Repeat procedure for the other 3 legs.
T2
T11
T14
A
A
A
B
B
T11
R
S
T5
T5
T1 T1
C
T14 x 4
U-Bracket
T1 x 8
M6x12L
Counter Sink Bolt
Note: After assembly, Bolt T1 should flush with base plate S
Repeat procedure for the other side.
T2 x 4
6
DON’T RETURN TO STORE
Step2
Please don’t tighten the bolts fully at this step.

7
Step3
Please don’t tighten the bolts fully at this step.
DON’T RETURN TO STORE
Repeat procedure for the other side.
T5 x 4 T11 x 4
M8 Metal Washer
M8x20L Bolt
A
D
AB
D
D
A
B
D
BT11
T5

Step4
Step5
8
Please don’t tighten the bolts fully at this step.
DON’T RETURN TO STORE
Repeat procedure for the other side.
D
E
T11 T9
T6
T11
E
E
D
D
T9 x 4 T11 x 8
M8 Nut
T6 x 4
M8x65L Bolt M8 Metal Washer
C
F
T10
T4
C
T10 x 2
T4 x 2
M6x55L Bolt M6 Metal Washer
Please don’t tighten the bolts fully at this step.
Repeat procedure for the other side.
And then securely tighten overall frame’s the bolts except T2 bolt on leg post top .
Note:Arrow on the rear leg crossbar should point upside.

9
Step6
Please tighten all the bolts fully at this step.
Step7
DON’T RETURN TO STORE
T9 x 2 T11 x 2 T12 x 2
M8 Metal Washer Plastic Washer
M8 Nut
T7 x 2
M8x77L Bolt
Please make sure the tabs on the ends of the seat support bars fully insert into
the brackets on the arms .
Note: There is a ‘FRONT’ label mark on the left & right arm.
The seat should be assembled the front of the arms.
FRONT
G
GG
I
I
I
IH
G
H
T12
T7
T9
T11
J
J
H
FRONT

Step8
Step9
10
T13 x 2
S-Hook
DON’T RETURN TO STORE
T13
J
G
J
L
K
H
H
L
L
L
K
K
L
L
K
J
E
Note: Long hanging bar should face outside.
Short hanging bar should face inside.

11
Step10
Please tighten all the bolts and nuts.
Step11
DON’T RETURN TO STORE
N
N
M
M
N
T8
T3
T3 x 4 T8 x 4
M6 Nut
M6x36L Bolt
Using as a swing.
Fully check with all the bolts and keep all them tightened at this step.
Q
O
P
Q

12
Step12
DON’T RETURN TO STORE
Converting the swing to a hanging bed.
J
L
Printed in China
K
L
F
J
F
J
F
J
F
J
The supporting bar of the back J should be inserted into the U-shaped brackets
at the same time by 2 persons and then fully press it, keeping the bed steady .
Removing the cushions.
Taking out the hanging bar L from the pin bolt of the back J .