Outsunny Tete-to-Tete Swing User manual

Columpio Balancín Jardín
IMPORTANTE-CONSERVE ESTA INFORMACIÓN PARA
SU CONSULTA POSTERIOR: ¡LEER DETALLADAMENTE!
Solamente para uso doméstico
Consejos de uso:
*Coloque el balancín de forma estable sobre un suelo plano.
*Montar el balancín al abrigo de la intemperie.
*Manténgase alejado de llamas abiertas.
*No cuelgue nada en la estructura.
*Envite la sobrecarga en los anclajes.
*Se aconseja no permanecer en el balancín cuando hay tormenta.
*Se recomienda resguardar en caso de viento o lluvia fuerte y en su
ausencia.
Precauciones antes del montaje:
*Prepare una zona de montaje limpia y seca.
*Verificar que el producto no este dañado.
*Controlar que no falta ninguna de las piezas.
Mantenimiento:
*Limpiar con la ayuda de un paño suave.
*Eliminar regularmente las hojas y/o agua recogidas sobre la lona.
*Compruebe regularmente los anclase.
Condiciones de almacenaje:
*La tela debe ser guardada totalmente seca, en un lugar limpio y seco
para evitar los riesgos de moho.
Precaución con los riesgos de pinzamientos o cortes durante el montaje.
El fabricante declina toda responsabilidad en caso de deteriores debidos
a una mala instalación o por causas meteorológicas.
IMPORTADOR POR:
SPANISH AOSOM, S.L.
c. roc gros no.15
08550 Els hostalets de Balenya
Barcelona
España
TEL: [phone]
http://www.aosom.es
Fabricado en China

XXLarge Bolt-Nut-Washer (S) 2pcs
10x280mm
Support (H2)
3x35mm
Screw (K) 26pcs
Tete-to-Tete Swing Assembly Instructions
Top Crossbar (A) 1pc Legs (B) 4pcs
Top Supports (C) 4pcs Cross Supports (D) 2pcs
Swing Posts (E) 2pcs
Seat (G) 1pc
Support (H1)
Table (I) 1pc
Seat Back (F) 2pcs
ADDITIONAL DETAILS / WARNINGS:
l This product is designed for a maximum capacity of 200 pounds per
seat.
lDo not throw away any packaging until assembly is complete.
lAssemble product on a soft surface so as not to scratch or damage the
item.
lKeep parts and packaging away from children and pets.
lFor ease of assembly, two people are recommended.
lTo allow for slight adjustments, do not over-tighten screws or bolts until
the swing is fully assembled.
lWe recommend using a rubber mallet to tap the pieces of this product
together during assembly and a power drill to tighten all screws.
lMake sure the frame is placed on a level surface.
lDo not leave children unattended on swing.
lDo not climb, jump off or hang from the swing or frame.
lDo not sit or stand on the swing table.
lTo avoid injury, periodically check the swing and all hardware for signs
of wear and possible metal fatigue that may require repair or
replacement.
lCheck all hardware to be sure screws, bolts and nuts are tight.
lSolid wood such as this has knots and marks which are normal and
should be considered an enhancement to the natural beauty of the
product.
PARTS LIST
Eye Bolt-Nut-Washer (P) 2pcs
Arm (J) 2pcs
Seat Supports (R) 4pcs
x85mm
88x100mm 8x120mm
8x140mm
XLarge Bolt-Nut-Washer (O) 4pcs
Medium Bolt-Nut-Washer (M)
2pcs
Small Bolt-Nut-Washer (L)
8pcs
Large Bolt-Nut-Washer (N)
4pcs
S-Hook (Q) 4pcs
HARDWARE LIST
2pcs 2pcs

R
R
K
K
K
K
1
STEP ONE
Insert two Supports (H1) in the middle of Seat (G) and secure with four
Screws (K). Insert the back of the Table (I) into both Seat Backs (F).
Insert Seat Backs (F) and Table (I) into Seat (G) and Supports (H1).
Secure Table and Seat Back using Fourteen Screws (K).
STEP TWO
Attach one Support (H2) to one Arm (J) and insert into the end of Seat
(G). Secure the Arm to the Support using one XXLarge Bolt-Nut-Washer
(S). Secure the back of Arm (J) to the side of Seat Back (F) using one
Medium Bolt-Nut-Washer (M). Repeat step for other side.
STEP THREE
Attach two Seat Supports (R) to the back of the left Seat Back (F) and
Seat (G) using four Screws (K), two Screws for each Support. Repeat
step for Right Seat Back.
Tete-to-Tete Swing Assembly Instructions

Made in China
STEP FOUR
Attach Swing Post (E) to the outside of Arm (J) and the inside back of
Seat (G) with two Large Bolt-Nut-Washers (N). Repeat step for other
side.
STEP FIVE
To build the frame, start by attaching Top Cross Bar (A) to Legs (B) using
two sets of X-Large Bolt-Nut-Washers (O), one each side. Attach Cross
Support (D) to the outside of each Leg (B) using four sets of Small Bolt-
Nut-Washers (L), two each side.
STEP SIX
Attach four Top Supports (C) to Top Cross Bar (A) and Legs (B) using
four Small Bolt-Nut-Washers (L) in the lower holes and two sets of X-
Large Bolt-Nut-Washers (O) in the top holes. Place two Eye Bolt-Nut-
Washers (P) up through the Top Crossbar (A).
STEP SEVEN
Securely tighten all Screws/Bolts and Nuts. Hang the Swing by
connecting the S-Hooks (Q) to the Swing and Frame using two S-Hooks
for each side. Assembly complete.
Tete-to-Tete Swing Assembly Instructions