bianco iCON Series User manual

BIA-SPC1 rev 5 Page 1
Installation and Operation Manual
SPC1

BIA-SPC1 rev 5 Page 2
TABLE OF CONTENTS
Page
QUICK GUIDE DRAINAGE PUMP –FLOATS CONNECTED TO PANEL 4-5
QUICK GUIDE DRAINAGE PUMP –FLOAT CONNECTED TO PUMP 6-7
QUICK GUIDE PRESSURE BOOSTING 8-9
QUICK GUIDE TRANSFER 10-11
1.0 INTRODUCTION
1.1 Applications 13
1.2 Technical parameters and features 13
1.3 Meanings of the icons shown on the LCD 15
2.0 GENERAL
2.1 Electrical connection to the power supply and pump 16
2.2 Connections for pump over temperature protection (where supplied) 17
2.3 Installing float switches and probes 17
3.0 INSTALLATION –DRAINAGE
3.1 Function switch setting 18
3.2 Diagrams for drainage by liquid level through float switches or probes 19
4.0 INSTALLATION –DRAINAGE
WITH AUTOMATIC PUMPS
4.1 Function switch setting 22
4.2 Diagram for drainage by liquid level 23
Cont....

BIA-SPC1 rev 5 Page 3
TABLE OF CONTENTS cont.
5.0 INSTALLATION –BOOSTING
5.1 Function switch setting 25
5.2 Diagrams for boosting by liquid level through float switches or probes 26
6.0 INSTALLATION –TRANSFER
6.1 Function switch setting 30
6.2 Diagrams for transfer by liquid level through float switches or probes 31
7.0 OPERATION
7.1 Parameter calibration and erasing 36
7.2 Switching to AUTO mode 37
7.3 Switching to MANUAL mode 37
7.4 Alarm Test and MUTE 37
7.5 Pump protection 37
7.6 Last five failure record 38
7.7 Pump accumulated running time 38
8.0 COMMUNICATION LINK 39
8.1 Basic Function 40
8.2 Special application 40
8.3 Technical parameters 40
9.0 TROUBLE SHOOTING GUIDE 41

BIA-SPC1 rev 5 Page 4
SPC1 QUICK GUIDE
DRAINAGE PUMP –FLOATS CONNECTED TO PANEL
DO NOT REMOVE BRIDGES BETWEEN TERMINALS 10&12
SET THE DIP SWITCHES ON THE INSIDE OF THE DOOR

BIA-SPC1 rev 5 Page 5
SPC1 QUICK GUIDE
DRAINAGE PUMP –FLOATS CONNECTED TO PANEL
CALIBRATION
SWITCH TO MANUAL PRESS MODE AND
STORE AT THE SAME TIME FOR 5 SEC
SWITCH TO AUTO PRESS MODE
CALIBRATE PUMP PRESS START THEN
AFTER PUMP RUNNING FOR 10
SECONDS PRESS STORE
TURN MCB ON

BIA-SPC1 rev 5 Page 6
SPC1 QUICK GUIDE
DRAINAGE PUMP –FLOAT CONNECTED TO PUMP
DO NOT REMOVE BRIDGES BETWEEN TERMINALS 10&12
SET THE DIP SWITCHES ON THE INSIDE OF THE DOOR
INSTALL EXTRA JUMPER

BIA-SPC1 rev 5 Page 7
SPC1 QUICK GUIDE
DRAINAGE PUMP –FLOAT CONNECTED TO PUMP
CALIBRATION
SWITCH TO MANUAL PRESS MODE AND
STORE AT THE SAME TIME FOR 5 SEC
SWITCH TO AUTO PRESS MODE
CALIBRATE PUMP PRESS START THEN
AFTER PUMP RUNNING FOR 10
SECONDS PRESS STORE
TURN MCB ON

BIA-SPC1 rev 5 Page 8
SPC1 QUICK GUIDE
PRESSURE BOOSTING
DO NOT REMOVE BRIDGES BETWEEN TERMINALS 10&12
SET THE DIP SWITCHES ON THE INSIDE OF THE DOOR
INSTALL EXTRA JUMPER

BIA-SPC1 rev 5 Page 9
SPC1 QUICK GUIDE
PRESSURE BOOSTING
CALIBRATION
SWITCH TO MANUAL PRESS MODE AND
STORE AT THE SAME TIME FOR 5 SEC
SWITCH TO AUTO PRESS MODE
CALIBRATE PUMP PRESS START THEN
AFTER PUMP RUNNING FOR 10
SECONDS PRESS STORE
TURN MCB ON

BIA-SPC1 rev 5 Page 10
SPC1 QUICK GUIDE
TRANSFER
DO NOT REMOVE BRIDGES BETWEEN TERMINALS 10&12
SET THE DIP SWITCHES ON THE INSIDE OF THE DOOR
INSTALL EXTRA JUMPER