BIG FURNITURE WAREHOUSE BRUNEL G-BNLLAMMNG User manual

BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS
Thank you for purchasing the BRUNEL LAMP TABLE. Please read
the instructions carefully to ensure safe operation of the product.
Size: W 400 X D 400 X H 530
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not destroy any of
the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be kept away
form young children whilst assembling your unit to avoid the danger of choking hazards.
Tools Required
X 1 1Hour
Set Up
V1 02/20
Page 1 of 15

IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
V1 02/20
Page 2 of 15
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS
INFORMATION
•Due to the size of this product we recommend that it is assembled in the room
intended for use.
•When you are ready to start, make sure that you have the right tools, plenty of
space and a clean, dry area for assembly.
•Unwrap all packaging materials and place the components on top of the carton
box or on a clean floor to prevent it from scratching.
•Check the pack and make sure you have all the parts listed.
•Ensure that this product is fully assembled and secured as illustrated before use.
•Check all screws or bolts are tightened and inspect regularly.
•This product should only be used on firm, level ground.
•Please dismantle for transportation.
•Tools not included.
WARNING
•Keep small parts out of reach of children.
•Make sure the legs remain in contact with the ground.
•DO NOT use power tools to construct this product.
•DO NOT tighten screws until fully assembled.
•DO NOT over tighten screws or bolts.
•DO NOT use this product if parts are missing, damaged or worn.
•DO NOT stand on the product.
•DO NOT place hot objects directly onto the surface. Always use a heat resistant
mat.
•Wipe Up any accidental spillage with a soft absorbent cloth.
•Please pay particular attention when children or animals are present to ensure
that no accidental entrapment occurs whilst operating this product.
•Incorrect installation could lead to injury, take care following instruction.
CARE INFORMATION
•Never use scourers, abrasives or chemical cleaners.
•To clean wipe with a sponge and warm soapy water. Do not use solvent based
cleaners or detergents as they can bleach or damage the product.

Please check the pack contents before assembling the product. If any components are missing, please
contact your retailer. The fittings pack contains small items that should be kept away from small children.
V1 02/20
Page 3 of 15
(P1)
(P2)
(P2)
(P3)
(P9)
(P11)
(P12)
(P4)
(P7)
(P5)
(P6)
(P8)
(P13)
(P10)
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS

Parts
TOP FRAME & TOP PANEL
1PC
Carton No: 1
P1
SIDE FRAME
2PCS
Carton No: 1
P2 P3
TOP SHELF
1PC
Carton No: 1
P4
BOTTOM PANEL
1PC
Carton No: 1
P5
SIDE PANEL LEFT
1PC
Carton No: 1
P6
SIDE PANEL RIGHT
1PC
Carton No: 1
P7
BACK PANEL
1PC
Carton No: 1
P8 P9
DRAWER FRONT
1PC
Carton No: 1
BOTTOM SUPPORT
2PCS
Carton No: 1
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS
V1 02/20
Page 4 of 15

Parts
DRAWER BACK
1PC
Carton No: 1
P10
DRAWER SIDE LEFT
1PC
Carton No: 1
P11
DRAWER SIDE RIGHT
1PC
Carton No: 1
P12
P13
V1 02/20
Page 5 of 15
DRAWER BOTTOM
1PC
Carton No: 1
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS

10 20 30 40 50 60 70 80 90 100 110 120
Fixings (to scale)
Ref Dimensions Qty
H1 4
H2 14
H3
JCBCW SCREW M6 X 50MM
4
H4
JCBC SCREW M6 X 15MM
12
H5 1
(Not to scale)
Ref Dimensions Qty
H9 M4 ALLEN KEY 1
CAUTION: There are many small components used in the construction of this product. Please keep
these components away from young children whilst assembling this product.
If you keep the fittings in a bowl during assembly you will be less likely to lose them
H10 METAL HANDLE 1
H11 DRAWER SLIDER 12" 1
H12 1
V1 02/20
Page 6 of 15
H6 10
H7 8
H8 8
CAM BOLT
CSK SCREW M4 X 38MM
CSK SCREW M3.5 X 16MM
HANDLE SCREW M4 X 19MM
DOWEL M8 X 25MM
CAM NUT 15MM
DRAWER SLIDER 12"
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS
L
R
L
R

V1 02/20
Page 7 of 15
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS

STEP 1 Parts
Required
(P4)
Top Shelf - 1pc
(P6)
Side Panel Left
- 1pc
(P7)
Side Panel Right
- 1pc
(P9)
Drawer Front
- 1pc
(P11)
Drawer Side Left
- 1pc
(P12)
Drawer Side Right
- 1pc
(H6)
Dowel M8x25mm
- 10pcs
(H7)
Cam Nut 15mm
- 8pcs
(H8)
Cam Bolt - 8pcs
V1 02/20
Page 8 of 15
(H7)
(H8)
Parts
Required
STEP 2
(P6)
Side Panel Left
- 1pc
(P7)
Side Panel Right
- 1pc
(H4)
CSK Screw M3.5
x16mm - 6pcs
(H11)
Drawer Slider 12"
L / R - 1pc
(H4)
(H11)
(P7)
(P6)
(H8)
(H7)
(H8)
(H7)
(H6)
(H6)
(H6)
(H6)
(H7)
(H7)
(P7)
(P6)
(P4)
(P9)
(P11)
(P12)
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS
Refer to page 7

Parts
Required
STEP 4 Parts
Required
STEP 3
V1 02/20
Page 9 of 15
(P5)
Bottom Panel
- 1pc
(P6)
Side Panel Left
- 1pc
(P7)
Side Panel Right
- 1pc
(H1)
JCBCW Screw
M6x50mm - 4pcs
(H9)
M4 Allen Key
- 1pc
(H1)
(H9)
(P5)
Bottom Panel
- 1pc
(P6)
Side Panel Left
- 1pc
(P7)
Side Panel Right
- 1pc
(P8)
Back Panel
- 1pc
(P7)
(P6)
(P5)
(P7)
(P6)
(P5)
(P8)
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS

Parts
Required
STEP 5 Parts
Required
STEP 6
V1 02/20
Page 10 of 15
Bottom
View
(P4)
Top Shelf - 1pc
(P6)
Side Panel Left
- 1pc
(P7)
Side Panel Right
- 1pc
(P8)
Back Panel
- 1pc
(P4)
(P7)
(P8)
(P6)
(H2)
(H9)
(P2)
Side Frame - 2pcs
(P3)
Bottom Support
- 2pcs
(H2)
JCBC Screw
M6x15mm - 4pcs
(H9)
M4 Allen Key
- 1pc
(P2)
(P3)
(P3)
(P2)
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS
(H2)
(H2)
(H2)
(H2)
Unlock Lock
Refer to page 7
TIP : Do not fully tighten
all H2 screw until
frame fully assembled.

Parts
Required
STEP 7 Parts
Required
STEP 8
V1 02/20
Page 11 of 15
(P2)
Side Frame - 2pcs
(P3)
Bottom Support
- 2pcs
(P5)
Bottom Panel
- 1pc
(H2)
JCBC Screw
M6x15mm - 6pcs
(H9)
M4 Allen Key
- 1pc
(P2)
(P2)
(P1)
(H2)
(H9)
(P1)
Top Frame &
Top Panel - 1pc
(P2)
Side Frame - 2pcs
(H2)
JCBC Screw
M6x15mm - 4pcs
(H9)
M4 Allen Key
- 1pc
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS
(P2)
(P3)
(P5)
(H2)
(H9)
(P5)
(P3)
(P2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
TIP : Do not fully tighten
all H2 screws until Cabinet
assembly is in place and aligned.

Parts
Required
STEP 9 Parts
Required
STEP 10
(P10)
Drawer Back - 1pc
(P11)
Drawer Side Left
- 1pc
(P12)
Drawer Side Right
- 1pc
(H3)
CSK Screw
M4x38mm
- 4pcs
V1 02/20
Page 12 of 15
(P12)
(P11)
(P10)
(H3)
(H3)
(P10)
(P12)
(P11) (P13)
(P10)
Drawer Back - 1pc
(P11)
Drawer Side Left
- 1pc
(P12)
Drawer Side Right
- 1pc
(P13)
Drawer Bottom
- 1pc
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS

Parts
Required
STEP 11 Parts
Required
STEP 12
(P11)
V1 02/20
Page 13 of 15
(P12)
(P9)
(P9)
Drawer Front
- 1pc
(P11)
Drawer Side Left
- 1pc
(P12)
Drawer Side Right
- 1pc
(P13)
Drawer Bottom
- 1pc
(P13)
(H4)
(P11)
Drawer Side Left
- 1pc
(P12)
Drawer Side Right
- 1pc
(H4)
CSK Screw
M3.5x16mm
- 6pcs
(H12)
Drawer Slider 12"
L / R - 1pc
(P11)
(P12)
(H12)
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS
Unlock Lock
Refer to page 7

Parts
Required
STEP 13 Parts
Required
STEP 14
(H10)
(H5)
(P9)
(H10)
(P9)
(P9)
Drawer Front
- 1pc
(H5)
Handle Screw
M4x19mm - 1pc
(H10)
Metal Handle
- 1pc
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS
V1 02/20
Page 14 of 15
(H5)

A- Width - 400mm
B- Depth - 400mm
C- Height - 530mm
D- Bottom Height - 160mm
OVERALL DIMENSIONS COMMENTS:
Lamp Table Dimensions Template:
Keep instructions for future reference
Complete Assembly
Periodically check to ensure that the components are in their proper position, free from damage.
Also, make sure the end of connectors are tight and secure.
V1 02/20
Page 15 of 15
BRUNEL LAMP TABLE
ASSEMBLY INSTRUCTIONS
A
B
C
D