BIG FURNITURE WAREHOUSE MELBOURNE G-MEL04CBWN User manual

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 1 of 20
Thank you for purchasing the Melbourne 4 Drawer Chest. Please read the instructions carefully
to ensure safe operation of the product.
Size:
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking hazards.
Tools Required
(W)600 x (D)400 x (H)685mm
Batch No :PO# 1271

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 2 of 20
IMPORTANT - READ CAREFULLY RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
INFORMATION
•Due the size of this product we recommend that it is assembled in thee room intended for use.
•When you are ready to start, make sure that u have the right tools, plenty of space and a clean,
dry area for assembly.
•
Unwrap all packaging materials and place the components on top of the carton box or on a clean
floor to prevent it from scratching.
• Check the pack and make sure you have all the parts listed.
• Ensure that this product is fully assembled as illustrated before use.
• Check all screws or bolts are tightened and inspect regularly
• This product should only be used on firm, level ground.
• Keep small parts out of reach of children.
• Make sure the legs remain in contact with the ground.
WARNINGS
•DO NOT use power tools to construct this product.
•DO NOT tighten screws until fully assembled.
•DO NOT over tighten screws or bolts.
•DO NOT use this product if parts are missing, damaged or worn.
•DO NOT stand or jump on the product.
CARE INFORMATION
•Never use scourers, abrasives or chemical cleaners
•To clean wipe with a sponge and warm soapy water. Do not use solvent based cleaners or
detergents as they can bleach or damage the product
•Never drag or pull this product across the floor as this could cause damage to the joints and could
result in failure to the product that will invalidate the warranty.

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 3 of 20
Please check the pack contents before assembling the product. If any components are missing,
please contact your retailer. The fittings pack contains small items that should be kept away from
small children.
B
A
C
D
D
E
F
G
G
G
G
H
H
I
I
I
I
J
J
K
L
MM

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 4 of 20
Parts
Description : Side Panel (L)
Qty : 1
Description : Side Panel (R)
Qty : 1
Description : Top Panel
Qty : 1
ABC
Description : Bottom Bar
Qty : 2
Description : Bottom Bar
Qty : 1
Description : Support Bar
Qty : 1
DEF
Description : Drawer Front
Qty : 4
Description : Side Panel (L)
Qty : 4
Description : Side Panel (R)
Qty : 4
GHI
Description : Drawer Back
Qty : 4
Description : Drawer Bottom
Qty : 4
Description : Drawer Support
Qty : 4
JKL
Description : Back Panel
Qty : 2
M

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 5 of 20
CAUTION: There are many small components used in the construction of this product.
Please keep these components away from young children whilst assembling this product.
If you keep the fittings in a bowl during assembly you will be less likely to lose them!
10 20 30 40 50 60 70 80 90 100 110 120
0
Ref Qty
Discription
aWood Dowel (D6 x 30mm) 36
b
c
Csk Screw (M3.1 x 20mm) 16
d
Csk Screw (M4.7 x 38mm) 16
e
Handle Screw (M4 x 20mm) 8
f
4
g
Nail Leg (5x8x13.5mm)
22
h
Nail Pin (19mm)
20
Minifix Bolt (M5 x 29mm)
20
(Not to scale)
Minifix Cam (15/12)
jDrawer Slide - 300mm 8
k4
l1
Handle - (7050) (64holes)
Allen Key (M4)
(to scale)
i8
Drawer Stopper (5 x 22mm)

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 6 of 20
Hints and Tips
Layout Parts on Soft Surface
Lay out all parts on a soft surface i.e. Rug, Carpet or Packaging Carton

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 7 of 20
a
a
x24
a
- Panel (A)
(1pcs)
- Panel (B)
(1pcs)
- Panel (D)
(2pcs)
- Panel (E)
(1pcs)
- Panel (F)
(1pcs)
- Panel (H)
(4pcs)
- Panel (I)
(4pcs)
- Panel (L)
(4pcs)
STEP 1 Parts
Required
x12
a
B
A
E
Dx2
F
Ix4 Hx4
Lx4

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 8 of 20
- Panel (A)
(1pcs)
- Panel (B)
(1pcs)
- Panel (C)
(1pcs)
STEP 2 Parts
Required
B
C
A
Gx4
g
g
gx8
gx12
- Panel (G)
(4pcs)

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 9 of 20
b
j
B
A
b
j
- Panel (A)
(1pcs)
- Panel (B)
(1pcs)
STEP 3 Parts
Required
x8
j
x16
b
FIRST
HOLE
SECOND
LAST HOLE

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 10 of 20
A
F
E
D
hx4
- Panel (A)
(1pcs)
- Panel (D)
(2pcs)
- Panel (E)
(1pcs)
- Panel (F)
(1pcs)
STEP 4 Parts
Required
h
D

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 11 of 20
B
F
D
E
D
hx4
- Panel (A)
- Panel (B)
(1pcs)
- Panel (D)
- Panel (E)
- Panel (F)
STEP 5 Parts
Required
h

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 12 of 20
ex4
B
AD
D
- Panel (A)
- Panel (B)
- Panel (D)
STEP 6 Parts
Required
e

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 13 of 20
h
- Panel (A)
- Panel (B)
- Panel (C)
(1pcs)
C
B
A
STEP 7 Parts
Required
hx4

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 14 of 20
g
g
x22
- Panel (M)
(2pcs)
M
M
C
B
STEP 8 Parts
Required

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 15 of 20
c
J
H
I
- Panel (H)
(4pcs)
- Panel (I)
(4pcs)
- Panel (J)
(4pcs)
STEP 9 Parts
Required
(x4)
cx16

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 16 of 20
J
H
I
L
I
L
J
K
- Panel (H)
- Panel (I)
- Panel (J)
- Panel (L)
(4pcs)
- Panel (H)
- Panel (I)
- Panel (J)
- Panel (K)
(4pcs)
- Panel (L)
STEP 10 Parts
Required
(x4)

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 17 of 20
h
G
I
L
K
- Panel (G)
(4pcs)
- Panel (H)
- Panel (I)
- Panel (J)
- Panel (L)
STEP 11 Parts
Required
(x4)
hx8

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 18 of 20
kx4
k
G
d
dx8
STEP 12 Parts
Required
IJ
H
(x4)
- Panle (G)
- Panel (H)
- Panel (I)
- Panel (J)
- Panel (L)

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 19 of 20
STEP 13 Parts
Required
i
ix8
H
G
I

MELBOURNE 4 DRAWER CHEST ASSEMBLY INSTRUCTIONS
Page 20 of 20
Complete Assembly
Your MELBOURNE 4 DRAWER CHEST is now completely assembled.
Periodically check to ensure that the components are in their proper position, free from damage.
Also, make sure the connectors are tight and secure.
Keep instructions for future reference