Big Game Treestands Eyecon Quick-Shot TV1001 User manual

User’s Manual
from
Big Game®Treestands
Model TV1001

2
User's Manual
F rst Ed t on, January 2012. Publ shed by BGHA, Inc., W ndom, MN.
© 2012 BGHA, Inc. All r ghts reserved.
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
Model TV1001

3
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
CAMERA DIAGRAM 4
ITEMS REQUIRED FOR STARTU 5
BATTERY INSTALLATION 6
MEMORY CARD INSTALLATION 7
QUICK SETU 8
ADVANCED SETTINGS & FUNCTIONS 9
QUIKSHOT MOUNTING & FIELD SETU 12
CAMERA CARE 14
TROUBLE SHOOTING 15
WARRANTY INFORMATION 16
RODUCT REGISTRATION CARD 17
WARNING! Prolonged exposure from looking directly into any
infrared light could cause cataracts or permanent retinal damage.
Do not look directly into the camera during test mode! Failure to
follow this warning may cause serious injury or blindness!
WARNING! Do not expose camera interior components, batteries, or
SD card to rain or water. Make sure camera and hands are completely
dry before handling. Failure to follow this warning may result in
serious damage to the camera and/or its parts, personal electrical
shock or death!
WARNING! Only batteries as designated in this manual should be
used. Failure to follow this warning may result in leaking batteries,
serious damage to the camera, and personal injury or death!

4
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
Clock
Date
Photos
Mode
Burst
Vid Lg
Res.
Delay
Photo
GB
16
SDHC
PM
SET
11:50
1 3 5
F
E
C
L
10s 30s 1m
1.3 3mp 5mp
10s 30s 1m 5m
Video
3 5
F
30s 1m
1 3m
30s 1m 5
Red Walk
Test Light
Green
Camera
Set-Up
Light
SD Card
Slot
Set Button C-Cell Battery
Comparment
C-Cell Battery
Comparment
Plus Arrow
Minus Arrow
Power
On/Off
Button
Case
Door
Lat h
Case Door
(Open)
Camera Options
Column

5
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
ITEMS REQUIRED FOR STARTU :
•6 C-Cell Alkaline Batteries (Sold separately)
•1 SDHC Storage Card (up to 32GB) (Sold separately)
NOTE: Eyecon™ Trail Camera’s can accept SD cards up to 32GB,
but testing shows that maximum performance is obtained at 16GB.
•1 External SD memory card reader for viewing
photos/videos. (Sold separately)
•OPTIONA : 1 Model TVA100 Extenda- ife
rechargeable lithium battery pack. (Sold separately)
NOTE: Your QuikShot Trail Camera is designed with a dual power
supply. The camera will operate using six C size alkaline batteries
or the TVA100 Extenda- ife battery pack, or a combination of both.
If both alkaline and the Extenda- ife pack are used together the
camera will run on the external Extenda- ife pack until depleted
and then automatically switch to the internal alkaline C batteries.
It will always run on the external pack first when both battery sources
are installed in the camera.
To see which battery source the camera is using, look at the battery
indicator. If there is an on the left side of the battery indicator this
means the camera is running on the TVA100 Extenda- ife ithium
pack. If a C has replaced the this means the camera has switched
over to the internal alkaline C batteries and you should remove the
Extenda- ife pack for recharging.

6
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
BATTERY INSTALLATION:
IF USING C-CE BATTERIES
1. Turn battery door lock to open position to release door located
on the bottom of the camera.
2. Insert (3) C-cell batteries, negative (–) side inserted first into one side.
3. Close the battery door and position lock to locked position.
4. Repeat on opposite side.
IF USING EYECON™ EXTENDA- IFE BATTERY PACK
1. Remove plastic plug on the back side of the camera. NOTE: Save
this plug for future use. It should A WAYS be in position when the
Extenda- ife Battery Pack is not being used.
2. Insert Extenda- ife Battery Pack by sliding it into position until
it "clicks" into place.

7
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
MEMORY CARD INSTALLATION:
TO INSTA THE SD CARD (Sold separately)
1. Open case door.
2. Insert the SD card face up into the SD Card Slot until you hear it
click into place. Press it once to remove.
PHOTO SIZE MEMORY CARD SIZE = NUMBER OF PHOTOS
(Resolution) 1GB 2GB 4GB 8GB 16GB 32GB
1.3 M 2000 4000 8000 16000 32000 64000
3.0 M 905 1808 3619 7238 14476 28952
5.0 M 595 1190 2381 4762 9524 19048
Video (30 Sec) 216 433 866 1733 3466

8
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
QUICK SETU :
Your QuikShot Trail Camera will come with the following standard
options already preset so that quality photos may be taken right out
of the box without changing any settings.
MODE: Photo BURST: 3 photo burst
RESO UTION: 1.3mp DE AY: 10 sec
If you wish to customize your own settings proceed to Advanced
Settings & Functions.
3 5
F
3m
Clock
Date
Photos
Mode
Burst
Vid Lg
Res.
Delay
Photo
PM 11:50
1 3 5
F
E
C
L
10s 30s 1m
1.3 3mp 5mp
10s 30s 1m 5m
Video
Camera
Options
Column
Battery
Indi ator
Arrow
Indi ates
Sele tion
User Setup Screen

9
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
ADVANCED SETTINGS & FUNCTIONS:
Press and quickly release the power button to activate the camera
and view the user setup screen.
Setting the functions is easy; simply use the plus or minus arrows to
select the feature (blinking) you wish to change and then push the
SET button. Each feature will blink and can be changed using the
+/– arrows and then push SET to move to the next feature.
C OCK: This will set the Time, Date and Year that will be stamped
onto the bottom of your photos.
To set the TIME: Use either the +or – arrows and scroll up until the
"Clock" starts to flash. Press the SET button and Clock will stop
flashing, and either "AM" or "PM" will start to flash. Use the arrows
to select the correct setting and press the SET button to move on to
the "Hour" setting. Use the +or – arrows again to set the correct
Hour, press the SET button and move on to get the "Minutes" to flash.
Arrow up or down the correct Minutes and hit SET to finish setting
the time. This will bring you back to the camera options column,
where you'll notice the "Clock" is flashing again
To set the MONTH: Use the +or – arrows and scroll down until the “Date”
starts to flash. Press the set button and you will see “MM” start to flash.
Pressing the set button again will allow you to select the correct Month.
Use the +or – arrows to change the Month setting.
To set the DAY: Press the set button again and you will see “DD” start to
flash. Pressing the set button again will allow you to select the correct day.
Use the +or – arrows to change the day setting.

10
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
To set the YEAR: Press the set button again and you will see “YY”
start to flash. Pressing the set button again will allow you to select the
correct year. Use the +or – arrows to change the year setting. Press
the set button again and this will bring you back to the camera
options column and you will notice the “Date” is flashing again.
PHOTO: This option will show you how many photos and/or
videos the camera has taken.
To check HOTOS: Use the +or – arrow to scroll down to “Photos”
MODE: Mode selects whether you would like the camera to take
still photos or take video clips. Options are: Photo (still) or Video
To set the MODE: Scroll down by pressing either the +or – arrows until
the “Mode” starts to flash. Press the set button until an arrow starts to
flash by either Photo or Video, this determines what mode the camera
is in. Press the +or – arrows to select either the Photo or Video
setting. Press the set button again to lock in the setting and exit Mode.
You will see “Mode” flashing again in the camera option column.
BURST: Burst selects how many photo images you would like the
camera to take in a row before set trigger delay kicks in. Options are:
1, 3, or 5
To set the BURST: Use the +or – arrows to scroll down until the “Burst”
starts to flash. Press the set button until an arrow flashes at one of the
Burst settings. Use the +or – buttons to select the desired Burst
setting. Press the set button again to lock in that setting and exit Burst.
You will see “Burst” flashing again in the camera options column.

11
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
VID G: This setting selects the length you would like each video
to be. Options are: 10 seconds, 30 seconds or 1 Minute.
To set the VIDEO LENGTH: Use the +or – arrows to scroll down until
the “Video G” starts to flash. Press the set button until an arrow
flashes at one of the Video settings. Use the +or – arrows to select
the desired Video G setting. Press the set button again to lock in
that the setting and exit Video G. You will see “Video G” flashing
in the camera options column.
RES: This setting selects the resolution at which you would like the
camera to take the pictures. A higher resolution photo requires more
storage. Options are: 1.3MP, 3MP, or 5MP.
To set the RESOLUTION: Use the +or – arrows to scroll down until
the “Res” starts to flash. Press the set button until an arrow flashes
at one of the Res settings. Use the +or – arrows to select the desired
Res setting. Press the set button again to lock in that setting and exit
Res. You will see “Res” flashing again in the camera options column.
DE AY: This setting selects the trigger delay at which you want to
run your camera. This is the amount of time between each burst.
Options are: 10 seconds, 30 seconds, 1 minute or 5 minutes.
To set the DELAY: Use the +or – arrows to scroll down until “Delay”
starts to flash. Press the set button until an arrow flashes at one of the
Delay settings. Use the +or – arrows to select the desired Delay setting.
Press the set button again to lock in that setting and exit Delay. You
will see “Delay” flashing again in the camera options column.

QUIKSHOT MOUNTING & FIELD SETU
The QuikShot comes with a 6 ft nylon mounting strap which allows
for quick and easy mounting. The camera back is unique in that it
has 12 vertical large bark biters and 5 different adjustment slots. This
allows for several strap placement options or another strap can be added
depending on your application. Either way, you can be guaranteed
that the QuikShot will mount to just about anything.
a. The ideal mounting height for deer or big game should be waist
high or around 36 to 40 inches from the ground. For shorter game
like bear or turkeys knee high will work better.
b. The motion detection angle of your QuikShot is about 50 degrees
which also matches the camera (FOV) Field of View. The motion
detection distance in ideal conditions is between 60–70 ft. This can
be greatly affected by weather conditions, animal body size, and
speed at which an animal passes through the detection zone.
ARMING THE CAMERA: There are two different ways your
QuikShot can be armed. The camera will automatically arm itself
after 30 seconds if the user does not press any of the camera buttons.
Or it can be force armed by pressing the +and – arrows at the same
time until the screen goes blank.
To wake the camera up simply touch the power on button, do NOT
hold the button down or the camera will shut off. NOTE: if the camera
is in the process of taking still photos or videos it must first complete
the process before it will wake up.
12
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.

CAMERA IGHTS: The red walk test light on your QuikShot
is used to help determine that your camera is set at the proper height
and is pointed in the right direction. The red walk test light can
only be activated by a combination of heat and motion. After either
20 photos or videos the red walk test light becomes inactive and will
not be seen until the user wakes the camera up again. The green light
will remain active during camera set up and indicates that everything
is working and ready to go. After either 20 photos or videos it will
turn off as well and remain off until the user wakes the camera up.
13
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.

14
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
CAMERA CARE
Moisture, vibration, and extreme temperature can cause severe damage
to your trail camera and should be avoided. Keeping your camera free from
moisture and vibration and using in the correct temperatures will
assure you many years of maintenance free service and operation.
MOISTURE: Although all Eyecon™ Trail Cameras have a very
durable plastic composite case which also makes them water resistant
even under the most extreme weather conditions, care must be taken
to prevent water damage.
• NEVER mount your trail camera upside down or leave the case open
for an extended period of time.
• NEVER change batteries, camera settings or SD cards in heavy rain.
•If your camera would happen to get water inside, remove the batteries
immediately and allow the camera to dry out for several days before
activating it.
VIBRATION: ike any electronic device your Eyecon™ Trail Camera
is designed with many small electronic components that are very
sensitive to vibration. Failure to follow careful handling & transport
may cause extreme and irreparable damage to your camera.
• NEVER drop the camera on a hard surface
• A WAYS transport your camera in a method to avoid bouncing
around or vibration.
TEMPERATURE: Recommended storage and operating
temperature: -10
°F to 120 °F.
• NEVER store your camera in a vehicle or other contained environment
with extremely high temperatures for an extended period of time!

TROUBLE SHOOTING
CAMERA NOT RES ONDING: If your camera at anytime does not respond
when the buttons are pushed or you cannot turn it off, your camera
maybe locked up. The best way to resolve this problem is to open one
of the battery doors for a period of 10 seconds. This will cut the main
power supply to the camera and will take care of the problem. If you
are using both the external TVA100 Extenda- ife litium battery pack
and internal Alkaline supply, you will need to do the same for both.
BAD SDHC CARD: Over time a SDHC or any storage device could
become corrupt. If your camera fails to acknowledge the SD card we
recommend that you replace the card with a new SD card or one from
a different EYECON™ Trail Camera that you know works. This will
help determine whether the problem is the SD card or the camera.
We do NOT recommend using cards that have been used in cameras
from different companies and/or different styles of cameras.
IMAGE QUALITY: Your QuikShot Trail Camera is designed to give you
optimum trigger speed along with great night photo clarity. There
may be some instances where an animal is moving extremely fast or
the light may be bad causing a smearing/blurry object within your
image. This is a natural part of photo taking and may occur from
time to time.
15
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.

WARRANTY AND REGISTRATION
Eyecon Trail Camera's 1 Year imited Warranty: For a period of 365
days after purchase, Big Game® Treestands will, at its discretion, repair
or replace this product for any reason of any defect or malfunction.
This warranty is only valid if the product is used for the purpose
intended and has not been tampered with and/or physically damaged
in any way. Products that have been damaged due to negligence or
misuse do not qualify for warranty replacement.
TO ACTIVATE WARRANTY:
•You MUST register your QuikShot Eyecon Trail Camera within
30 days of purchase to receive any warranty protection!
•You MUST keep a copy of your receipt as Proof of Purchase for
any warranty protection!
TO OBTAIN A WARRANTY C AIM:
1. You MUST call our customer service department at 800-268-5077
or 507-831-4350 and follow all troubleshooting requests first.
2. If Warranty Claim is approved, a RA Number will be given to you;
keep this for your records.
3. Remove your SD card and batteries (any items other than original
camera casing will be destroyed and not returned with new item)
4. Include a copy of your original receipt, your RA#, and a check
or credit card number for $20.00 shipping/handling in the box.
5. Ship the box prepaid to: Big Game Treestands, Camera Returns,
1820 N. Redding Ave. Windom, MN 56101. Make sure to put the
RA# in bold letters on the outside of the box.
16
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.

17
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
RODUCT REGISTRATION
Product Purchased
Model Number
Serial Number
Owner’s Name
Street Address
City State Zip Code
Email Address Phone
Owners Age (optional) Sex (optional) M F
Date Purchased
Purchased From (Dealer Name)
How did you hear about us: Catalog Webpage Friend
Magazine Other, Please Explain:
Are you a: Bow Hunter Gun Hunter Both
Treestand Pref: Fixed Position Climbing adderstand
To activate your product’s warranty, please mail in this completed
registration card or submit it online at www.biggametreestands.com
#

18
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
Remember to activate your product’s warranty?
See warranty information and registrtion
instructions on page 16 and then complete and
mail in the registration card on page 17
or submit it online at:
www.biggametreestands.com

19
LEASE REGISTER TO ACTIVATE YOUR RODUCT'S WARRANTY.
Big Game®Tree tand
PO Box 382 • 1820 North Redding Ave • Windom, MN 56101
800-268-5077 • 507-831-4350
OWNER’S RECORD
Product Name __________________________________________________
Model Number _________________________________________________
Serial Number__________________________________________________
Purchased From ________________________________________________
Purchased Date _________________________________________________
YOU MUST RETURN THE COMP ETED REGISTRATION CARD ON
PAGE 17 WITHIN (30) DAYS OF THE PURCHASE IN ORDER TO
ACTIVATE THE IMITED WARRANTY COVERAGE. (Make sure
to include date purchased when registaring!)
NOTES:

BGTTV10010112A
PO Box 382 • 1820 North Redding Ave • Windom, MN 56101
800-268-5077 • 507-831-4350
www.BigGameTreestands.com