Bikefit 7050112 User manual

Bike Fitting Tool
Project a perfectly vertical line quickly and easily with our
new extra bright SELF-LEVELING LASER. Assess front
view, side view and save time.
Use to easily and quickly
assess alignment. A multi-
purpose BikeFit device.
Part# 7050112
Form# 0010157
Front View:
The goal is to decrease side to side knee movement. Be aware that not all cyclists will have the Knee Dot in alignment with the Toe Dot.
a.While cyclist is safely on a Stationary Trainer, place velcro Knee Dot Strap
(BikeFit Part# 7040200) around each leg with
dot just below knee cap and covering the
tibial tuberosity (the large oblong portion
below knee).
Self-leveling Laser
LASER RADIATION
DO NOT STARE INTO BEAM OR VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS
CLASS 2M LASER PRODUCT
b.Place a Toe Dot Sticker (BikeFit Part# 7011201) on each shoe in front
over the second toe.
c.
Place laser
in front of
bike. Laser needs
to be in line with
one leg (toe dot).
Turn on Laser to
show a vertical line.
Adjust laser to stay
in alignment with
the toe dot. Have
the cyclist start
pedaling.
d.Watch Knee
Dot relative the
Toe Dot line.
Does knee track
toward the
insider or the
outside the toe
dot line? This will
help guide any
adjustments.
e.
Laser will
provide
you with a straight
line to work as
a reference
for making
adjustments to
cleats to improve
pedaling motion
alignment.
Side View:
The goal for this observation is to
determine Saddle fore/aft adjustment.
a.Position the Laser to the side of the bicycle. Project line to bisect the
pedal axles when either is in 3 o’clock spot. b.
Rotate each crank to the 3 o’clock
position and recheck to make sure
the laser is in line with both pedal spindles.
c.
Knee over Pedal Spindle (KOPS) is a
good starting point for most. Some
road and mtn cyclists who spend much time
climbing may opt for further back position.

425-821-7237
12518 130th Lane NE • Kirkland, WA 98034 • USA
www.BikeFit.com
LIMITED WARRANTY
BikeFit warrants this laser by providing a limited 60-day warranty
from purchase date. Should this product fail due to defects in
material or workmanship under normal use within this period,
BikeFit will at its own discretion, repair or replace the defective
part. This warranty is not transferable.
This warranty does not cover products which are misused,
abused, mishandled, improperly installed, improperly stored,
changed, modified, or are subjected to extreme temperatures or
extreme moisture levels. This warranty is not valid for products
used for any purpose other that the purpose for which they were
originally intended.
The repair(s) or replacement(s) of our products are contingent
on availability of the items. If a warranty claim is filed after the
product has been discontinued or modified, BikeFit reserves the
right to honor the warranty in the following fashions.
1. To repair or replace the affected component with a new
component of the same style.
2. To repair or replace the affected component with similar and
comparable product.
This warranty is the exclusive warranty of BikeFit and is in lieu of
all other warranties, express or implied. In no event shall BikeFit
be liable for the consequential, indirect or incidental damages
resulting from the installation, use, or failure of its product.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions
may not apply to you. This limited warranty gives you specific
legal rights. You may also have other rights that vary from state-
to-state.
To submit a claim under this warranty, contact the nearest
BikeFit dealer, or send a letter explaining the defect, with a dated
sales receipt as proof of purchase to (do not send merchandise
unless requested by the Claims Department):
12518 130th Lane NE
Kirkland, WA 98034
SAFETY INSTRUCTIONS
WARNING: Never shine a laser directly into eyes, doing
so can cause serious eye injury. Laser level is a precision
tool, handle with care. Avoid water, shock, vibrations, and
extreme temperatures.
• Follow the these safety instructions.
• Avoid exposure, laser radiation is emitted from this tool.
• Keep the laser ‘on’ only when necessary.
• Do not disassemble Laser.
• Do not aim laser at reflective surfaces.
• Restrict unauthorised use.
• Do not remove warning labels.
Made in China.
DANGER
LASER RADIATION -- DO NOT STARE
INTO BEAM OR VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS
Max output power : <1mw@635nm
Class 2M Laser Product
REPLACING
THE BATTERIES
Unhinge side door
latch to expose
battery cavity.
Requires (3)three AA
1.5V Alkaline or Nicad
batteries.
OFF
ON
pendulum
Unlocked pendulum
Locked
OPERATION
For transport keep
in ‘Off /Locked’
position to prevent
damage to laser.
If moved, allow
4-6 seconds of
stabilization for
lines to be visible.
Laser lines may
swing slightly due
to vibration from
surroundings.