Billi Alpine Sparkling User manual

User guide
Billi Alpine Sparkling

User guide
Billi Alpine Sparkling.
Thank you for choosing to install a
Billi Alpine Sparkling Instant Chilled
Filtered Water System. Your Alpine Sparkling
is manufactured to exacting standards
using high quality materials and with proper
maintenance and care, should function for
many years. The Billi service representative
to contact for any service requirements or
to supply replacement filter cartridges is:
Filter cartridges are also available
online at www.billi.com.au
Should any problems arise and our
representative is unavailable or unable
to help, please use our FREECALL
phone number: 1800 812 321.
Insert agent details
2

User guide
Billi Alpine Sparkling.
3
Warnings
– For continued safety of this appliance
it must be installed, operated and
maintained in accordance with the
manufacturer's instructions.
– Your appliance should be installed
by a suitably qualified tradesperson.
– For correct operation of this appliance
it is essential to observe the instructions
as outlined in this booklet.
– Do not use this appliance with water
that is microbiologically unsafe or with
water of unknown quality without adequate
disinfection before the system. Systems
certified for cyst reduction may be used
on disinfected water that may contain
filterable cysts.
– Filter replacement must be performed
at intervals of not more than 12 months.
– Use this appliance only as directed
in these instructions and only for its
designed purpose.
– This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
– Children should be supervised to ensure
that they do not play with the appliance.
– If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order
to avoid creation of a hazard.
– New hose sets supplied with the appliance
are to be used. Old hose sets should not
be re-used.

User guide
Billi Alpine Sparkling.
Cupboard space requirements
Do not store kitchen products next to vents.
Refer to install guide for space requirements.
General maintenance
Your Billi Alpine Sparkling has been designed
to require minimal maintenance other than
replacement of filter cartridges. During each
filter change, check all water connection
fittings for signs of leakage. Check all tubing
for any signs of damage. Check the cupboard
area around the base of unit for any signs of
moisture.
Cleaning the dispenser
Your Alpine Sparkling dispenser is fabricated
from robust metal with a tough protective
chrome plating. Care of dispenser is as with
any chrome plated tap ware. Avoid using
abrasive cleaners. Wipe clean using a damp
cloth. Use of a non-solvent, non-smearing
cleaner such as Windex is recommended.
Do not pour water over dispenser.
Normal operation
—Slimline dispenser
To dispense filtered water, the appropriate
dispenser tap lever will need to be rotated.
The sparkling lever will automatically return
to the o position. The chilled water lever will
stay open to allow carae filling. The spout
can be swivelled to suit your installation.
—Adjusting chilled water temperature
The chilled water temperature can be adjusted
to suit your preference. The grey control knob,
located on the front panel of the unit, can be
adjusted if a cooler or warmer temperature
is required.
4

User guide
Billi Alpine Sparkling.
—Billi filter cartridges
The Alpine Sparkling features the unique
Billi filtration system, incorporating sediment
and chemical removal elements. All Alpine
Sparkling filters are manufactured using
bacteria and biofilm resistant materials for
improved water quality.
Premium filters provide a better tasting
water due to the high quality, carbon
chemical removal filter. Sub micron rated,
these filters have excellent chemical
absorption, removing or reducing chlorine,
volatile organic compounds (VOCs), chemicals,
tastes and odours. Use only genuine filters as
designed for this system. All drinking water
filtration systems should be flushed after
a period of non-use.
—Replacement of filter cartridges
Periodic replacement of your Alpine Sparkling
filter cartridge is necessary to maintain
the cleanliness of your drinking water.
Billi recommends a filter replacement
every 12 months. A replacement filter
change installation service is available.
If you wish to install the replacement filter
cartridges yourself, your Billi representative
will provide genuine Billi replacement filter
cartridge sets.
—Filter options
— 994001 5.0 Nominal micron rating
— 994002 0.2 Nominal micron rating
Use only genuine Billi filter cartridges
as designed for this system.
If the system has not been used for a period
of 48 hours or more, lift the dispenser lever
and flush the system for at least 1 minute.
5

User guide
Billi Alpine Sparkling.
User service
—Replacing Filter Cartridge
1. Turn o blue tap under bench.
2. Operate dispenser lever to release pressure.
3. Hold filter and swing towards you slowly.
The top of the filter is in a hinged cradle
assembly. It should stop after approximately
30 degrees of travel.
4. The filter can now be released from the
holding cradle by pulling down on the filter.
5. Take care not to spill water in the base of the
tray. If so wipe gently with absorbent paper.
6. Install new filter into the same location
by pushing all the way up into the cradle.
7. Push filter back into the unit until it locks
into place.
8. Turn on blue tap under bench and check
for water leaks.
9. Operate dispenser lever and run water for 3
minutes to flush and condition the new filter.
6

User guide
Billi Alpine Sparkling.
Removing the CO2cylinder
1. Isolate the water supply and turn o
the power.
– This will prevent the internal pump
from pressurizing the system.
2. Turn o the CO2regulator by turning the
black knob anti-clockwise.
3. Drain any remaining pressure by activating
the sparkling water option on the dispenser
installed.
Ensure the pressure gauge shows near to
zero pressure – if the pressure is less than
one bar, and the dial is fully anti-clockwise,
then the cylinder can be removed with only
a small amount of CO2escaping
4. Hold the regulator and rotate the Cylinder
clockwise to remove.
– If the bottle is not empty, CO2may escape
while you are turning the bottle. The bottle
will self-seal prior to the thread being free
from the regulator.
– Avoid breathing air containing CO2or
contact with the cold escaping gas as
per the Safety Data Sheet.
7

User guide
Billi Alpine Sparkling.
Installing the CO2cylinder
1. Ensure all connections between the
regulator and unit are secure.
Position the regulator on top of the CO2
cylinder.
2. Tighten the bottle by rotating anti-clockwise.
– CO2will escape while you are turning the
bottle. Continue to turn the bottle to form
a seal with the regulator.
3. Open the pressure regulator by turning the
black knob clockwise.
– Set the initial pressure to around 2.5 Bar.
– Turn on the unit power and water supply.
– Wait for the unit to come back to
temperature.
4. Check bottle and connections for leaks with
soap or commercial leak indicator.
NOTE: the ¼" tube and pushfit fittings may
settle when the pressure is turned on.
5. Increase the pressure to set your level of
carbonation.
Initial set point may vary once the unit is
running, you may need to reset the pressure
once the system has stabilised.
WARNING:do not set the pressure above 5 bar.
8

Warranty
Subject to the warranty exclusions set
out below, if a defect in a new product
supplied by Billi Pty Ltd (ACN 124 066 717)
("Billi") and purchased by you ("customer") from
a reseller authorised by Billi occurs within 24
months of the date of purchase of the product
as a result of defective materials or defective
manufacture by Billi, and Billi receives a written
claim (containing details of the product defect
together with a receipt from the reseller of the
products showing the date of purchase of the
products, or such other proof of purchase and
the date of purchase as Billi may accept) within
25 months of the date of purchase, Billi shall, at
its discretion:
a) direct an accredited service provider
to attend the customer's premises
(provided that the premises are located
within Australia) and repair the defect free
of charge; but if the customer's premises
are located more than 25 kilometres from
one of Billi's authorised service agent's
locations then the customer will be liable for
any increased freight costs, fees, charges or
levies Billi may incur as a result of fulfilling
its obligations under this paragraph a) of this
Product Warranty; or
b) direct the customer to return the product to
Billi so that Billi may provide a replacement
product free of charge. If Billi elects to do
this, Billi will also pay the necessary freight
charges, and the customer will pay for the
removal of the product and the costs of
reinstalling the replacement product.
Any product replaced or repaired under
this Product Warranty will be covered by the
product's remaining warranty period, or three
months, whichever is greater. If the product
or any part thereof is replaced by Billi under
this Product Warranty, all of the right, title and
interest in and to the replaced product or part
shall vest in Billi upon it being replaced.
—Warranty exclusions
1. Billi shall not be liable under this
Product Warranty:
a) unless the product was installed
correctly and as per the installation
instructions supplied with the product;
b) if the defect is contributed to or caused
by any improper usage of the product
or usage of the product for purposes
other than that for which the product
was designed or intended;
c) if the defect occurs wholly or partially
as a result of any act or omission by the
customer, or any person other than Billi;
d) if the product is subject to misuse,
neglect, accident or abuse or the
customer continues to use the product
after the defect becomes apparent;
e) if the product is damaged as a result
of poor water quality;
f) if the product is repaired, or any attempt
to repair the product is made, by anyone
other than an authorised repairer of the
products acting at Billi's direction; or
g) if the product is altered or modified
in any way unless such modification
has been approved in writing by Billi.
2. Notwithstanding anything to the contrary,
filters are not covered by this (or any other)
Product Warranty.
User guide
Billi Alpine Sparkling.
9

—Limitation of liability
3. Except for the Product Warranty set
out above, and except for any liability
in connection with the supply of goods
imposed on Billi by the Trade Practices
Act 1974 (Cth) and other similar state
and territory legislation (including for
breach of implied conditions and warranties)
which cannot, or which can only to a limited
extent, be lawfully excluded, all liability of,
and conditions and warranties relating
to the supply of the products by, Billi are
hereby expressly excluded. Any such
liability which cannot be lawfully excluded
is limited, at Billi's option, to any one or
more of the following:
a) the replacement of the goods or the
supply of equivalent goods;
b) the repair of the goods;
c) the payment of the cost of replacing the
goods or of acquiring equivalent goods; or
d) the payment of the cost of having the
goods repaired.
User guide
Billi Alpine Sparkling.
10

Billi Pty Ltd
42 Lucknow Crescent, Thomastown
Victoria 3074 Australia
Telephone [phone]
Facsimile [phone]
www.billi.com.au
Designed and manufactured in Australia.
As Billi Pty Ltd has a policy of continual
improvement, all details are subject
to change without notice. All goods
are sold subject to our published terms
and conditions. Billi is a registered
trademark. 0914