Billi B-6000 User manual

B–6000
Boiling and Chilled
Filtered Water System
User guide

User guide
B–6000.
2
Thank you for choosing to install a
Billi B-6000 Drinking Water Appliance.
Your B-6000 is manufactured to
exacting standards using high
quality materials and with proper
maintenance and care, should
function for many years.
The Billi service representatives to
contact for any service requirements
or to supply replacement filter
cartridges is:
Filter cartridges are also available
online at www.billihome.com.au
Should any problems arise and our
representative is unavailable or unable
to help, please use our FREECALL
phone number: 1800 812 321.
Insert agent details

User guide
B–6000.
Product warranty
Subject to the warranty exclusions set out
below, if a defect in a new product supplied
by Billi Pty Ltd (ACN 124 066 717) ("Billi")
and purchased by you ("customer") from
a reseller authorised by Billi occurs within
24 months of the date of purchase of the
product as a result of defective materials
or defective manufacture by Billi, and Billi
receives a written claim (containing details
of the product defect together with a receipt
from the reseller of the products showing the
date of purchase of the products, or such other
proof of purchase and the date of purchase as
Billi may accept) within 25 months of the date
of purchase, Billi shall, at its discretion:
a) direct an accredited service provider
to attend the customer's premises
(provided that the premises are located
within Australia) and repair the defect
free of charge; but if the customer's
premises are located more than
25 kilometres from one of Billi's
authorised service agent's locations
then the customer will be liable for
any increased freight costs, fees,
charges or levies Billi may incur
as a result of fulfilling its obligations
under this paragraph a) of this
Product Warranty; or
b) direct the customer to return the
product to Billi so that Billi may provide
a replacement product free of charge.
If Billi elects to do this, Billi will also pay
the necessary freight charges, and the
customer will pay for the removal of the
product and the costs of reinstalling
the replacement product.
Any product replaced or repaired under
this Product Warranty will be covered by
the product's remaining warranty period,
or three months, whichever is greater.
If the product or any part thereof is
replaced by Billi under this Product Warranty,
all of the right, title and interest in and to the
replaced product or part shall vest in Billi
upon it being replaced.
—Warranty exclusions
1. Billi shall not be liable under this Product
Warranty:
a) unless the product was installed correctly
and as per the installation instructions
supplied with the product;
b) if the defect is contributed to or caused
by any improper usage of the product or
usage of the product for purposes other
than that for which the product was
designed or intended;
c) if the defect occurs wholly or partially
as a result of any act or omission by the
customer, or any person other than Billi;
d) if the product is subject to misuse,
neglect, accident or abuse or the
customer continues to use the product
after the defect becomes apparent;
e) if the product is damaged as a result
of poor water quality;
f) if the product is repaired, or any attempt
to repair the product is made, by anyone
other than an authorised repairer of the
products acting at Billi's direction; or
g) if the product is altered or modified
in any way unless such modification
has been approved in writing by Billi.
g) if the product is altered or modified in
any way unless such modification has
been approved in writing by Billi.
2. Notwithstanding anything to the contrary,
filters are not covered by this (or any other)
Product Warranty.
3

User guide
B–6000.
—Limitation of liability
3. Except for the Product Warranty set
out above, and except for any liability
in connection with the supply of goods
imposed on Billi by the Trade Practices
Act 1974 (Cth) and other similar state
and territory legislation (including for
breach of implied conditions and warranties)
which cannot, or which can only to a limited
extent, be lawfully excluded, all liability
of, and conditions and warranties relating
to the supply of the products by, Billi are
hereby expressly excluded. Any such
liability which cannot be lawfully excluded
is limited, at Billi's option, to any one or
more of the following:
a) the replacement of the goods or
the supply of equivalent goods;
b) the repair of the goods;
c) the payment of the cost of replacing the
goods or of acquiring equivalent goods; or
d) the payment of the cost of having the
goods repaired.
General Maintenance
Your Billi B-6000 has been designed to require
minimal maintenance other than replacement
of filter cartridges. During each filter change,
check all water connection fittings for signs
of leakage. Check all tubing for any signs of
damage. Check the cupboard area around
the base of unit for any signs of moisture.
For air cooled units, ensure side vents of
the under bench module are kept clear
and airflow is not obstructed. Restricted
airflow will cause inecient operation
of the refrigeration system.
Warnings
– For continued safety of this appliance
it must be installed, operated and
maintained in accordance with the
manufacturer's instructions.
– Your appliance should be installed
by a suitably qualified tradesperson.
– For correct operation of this appliance
it is essential to observe the instructions
as outlined in this booklet.
– Do not use this appliance with water
that is microbiologically unsafe or with
water of unknown quality without adequate
disinfection before or after the system.
Systems certified for cyst reduction may
be used on disinfected water that may
contain filterable cysts.
– Filter replacement must be performed
at intervals of not more than 12 months.
– Use this appliance only as directed
in these instructions and only for its
designed purpose.
4

5
User guide
B–6000.
– This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
– Children should be supervised to ensure
that they do not play with the appliance.
– DANGER: The operation of the thermal
cut-out indicates a possibly dangerous
situation. Do not reset the thermal cut-out
until the water heater has been serviced
by a suitably qualified person.
– WARNING: Do not connect any restrictor or
pressure relief device to the vent pipe of this
water heater if installed.
– If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order
to avoid creation of a hazard.
– New hose sets supplied with the appliance
are to be used. Old hose sets should not
be re-used.
Caution and Safety
Boiling water is dangerous and can cause
severe burns, particularly with young children.
Boiling water must always be handled with
caution. Use this appliance only as directed in
these instructions and only for the purpose for
which it has been designed. Your Billi B-6000
is designed to be safe and practical.
The following safety features have
been included
– Ergonomic levers control water flow.
– Levers located safely above water outlet.
– Smooth electronically controlled boiling
water flow rate. Flow is briefly reduced as
water first enters cup to prevent splashing.
– Dispenser remains cool to touch.
– Childproof safety switch.
– Boiling water Safety Isolation mode.

Normal operation
—Dual action levers
To dispense drinking water from your
Billi B-6000, the hot or cold levers may be
depressed or lifted. When lifted, the levers
will latch for continuous delivery until
released with a light press. The B-6000
will not dispense hot and cold water
simultaneously. Water will not flow
if both levers are pressed together.
—Dispenser swivel
The B-6000 dispenser incorporates a swivel
function, allowing the dispenser to be swung
out of the way if more sink space is required.
A central position stop provides positive
location during normal usage.
—Safety timeout
Your Billi B-6000 incorporates a water delivery
safety timeout to prevent an uncontrolled flow
of water. Water flow stops automatically after
a set time interval. Flow can be started again
by releasing and pressing the dispenser lever.
Boiling water timeout – 20 secs;
Chilled water – 1 minute.
—Dispenser indicator icons
The boiling water cup icon flashes red
while water is heating and remains steady
when boiling water temperature is reached.
The chilled water drinking glass icon flashes
blue when cold water is not yet suciently
chilled and remains steady once the
selected temperature is reached.
—Time switch
Your Billi B-6000 incorporates an energy
saving time switch. This function allows
the B-6000 to automatically turn ON and OFF
at selected times. Individual days can be
set to be active or non-active.
Refer to Setting Instructions, page 9.
User guide
B–6000.
6

User guide
B–6000.
—Childproof safety switch
Your Billi B-6000 is fitted with a childproof
safety lock-out feature to protect against
accidental dispensing of boiling water and
the risk of burns. When this mode is activated,
the safety switch button located on the rear
of the dispenser must be pressed and the
hot lever lifted or pressed within 8 seconds
to dispense boiling water. To activate, refer
to Options, page 10. During this mode,
the red hot cup icon is on, and then gives
2 rapid flashes every 2 seconds.
—Water delivery temperatures
The boiling water and chilled water
temperatures can be adjusted to suit
individual preferences.
– Hot water temperature range: 80°C - 98.9°C.
– Cold water temperature range: 6°C - 20°C.
To alter, refer to Options, page 10.
—Standby mode
An energy saving Standby mode can
be selected to activate after a period of
non-use. Once activated, the boiling water
temperature can drop to 80°C and the chilled
water temperature can rise to 15°C. A touch
of either dispenser lever cancels the standby
and the B-6000 resumes its normal operating
mode to deliver boiling or chilled water.
The time needed to elapse before the B-6000
enters this mode can be varied. Refer to
Options, page 10. During Standby mode,
the red and blue dispenser icons briefly
turn o for 0.5 seconds every 3 seconds.
—Boiling water disabled mode
Your Billi B-6000 features an additional
boiling water Safety Isolation feature.
Once activated, delivery of boiling water
becomes totally disabled. Chilled water
can be dispensed normally.
– To activate: Press the safety button located
on the rear of the dispenser 3 times in
rapid succession, i.e. within 1.5 seconds.
– To cancel: Repeat the activation procedure.
During this mode, the hot cup icon gives
a brief red flash every 3 seconds.
7

8
User guide
B–6000.
Dispenser icon codes
Normal Operation
Operating temperatures of hot
and cold water not yet reached
Childproof Safety Lock activated
Boiling water disabled
System Locked/Override O
Filter change due
Unit in Fault Mode
Red
Blue
Red
Blue
Red
Blue
Red
Blue
Yellow
Yellow
Red
Yellow
Blue
Yellow
Yellow

9
User guide
B–6000.
Setting instructions
—Normal display
Current status may be displayed as follows.
Timeswitch ON/OFF Indicates the B-6000 has been switched ON or OFF by the inbuilt
time switch control. During OFF mode, the dispenser icons are
o and give a brief orange flash once every 10 seconds.
Override ON/OFF The B-6000 can be manually turned ON or OFF by pressing the
ON/OFF button. The status remains as selected for a period
of 2 hours, after which it returns to automatic ON/OFF control.
Locked ON/OFF The ON/OFF status can be permanently locked ON or OFF.
Use ON if 24 hour, 7 days a week service is required; or OFF if
user is going away for an extended period. To activate or deactivate:
press the ON/OFF button and hold down until the required status
is displayed.
Safety switch The child proof safety Switch mode has been activated.
To set, refer to Options, page 10.
Boiling disabled The boiling water disabled mode is activated.
See Normal Operation, page 6.
Standby A period of non-use has elapsed and the B-6000 has switched
to the energy saving standby mode.
Billi B-6000
Instant Boiling and Chilled Filtered Water System
Back Finish Start Select Help On/O
Daylight
Saving
Model 4100 G06670134
SW: 2.40 09:51 AM
Tue 07 NOV 2010
TIMESWITCH ON
Normal display
Model
Software
version
Day and date
Serial number
Time
Current status

10
User guide
B–6000.
—Daylight saving
Time adjustment for daylight saving
is made by pressing either the START
or FINISH buttons at the beginning
or end of daylight saving.
—Menu
To access the menu, press the
SELECT button. The menu functions are:
– To move the highlighted cursor,
press the or buttons.
– To activate the highlighted cursor,
press SELECT.
– To return to previous screen,
press BACK.
—Setting time and date
Screen shows currently set time, day and date.
– Press or buttons to move the highlighted
cursor.
– Press SELECT to activate. The highlighted
item flashes.
– When flashing, press or to change
setting.
– Press SELECT. Highlighted cursor stops
flashing. Cursor automatically advances
to next setting. Repeat above activation
procedure.
– Press BACK once to return to previous
screen or twice to return to normal display.
—Setting time switch
Screen shows active and non-active days.
Turn-on and Turn-o times for active
days are displayed.
– Press or buttons to move the
highlighted cursor.
– Press SELECT to activate.
The highlighted item flashes.
– When flashing, press or
to change setting.
– Press SELECT to confirm and
advance to next setting. Repeat above
activation procedure.
– Press BACK twice to return
to normal display.
Billi B-6000
Instant Boiling and Chilled Filtered Water System
Back Finish Start Select Help On/O
Daylight
Saving

11
User guide
B–6000.
—Options
The screen displays the following options and
settings. Press and buttons to select and
activate or alter the required setting.
– Safety Switch: Childproof safety switch
is activated by selecting ON.
– Hot Temp Set: Hot water temperature
can be set between 80°C and 98.9°C.
– Cold Temp Set: Cold water temperature
can be set between 6°C and 20°C.
– Standby Mode: Activated by selecting ON.
– Standby Time Set: Period of non-use
before standby mode is activated.
Range 0.5 to 4.0 hours.
– Filter Change Help: Step-by-step graphic
instructions showing filter change procedure.
– Filter Flush: Automatic flush cycle to clean
filters after 2 days of non-use.
—Statistics
Screen displays information only.
– Hot, Cold: Temperature of boiling
and chilled water.
– Hot Cups: Total number of boiling water
cups dispensed.
– Cold Cups: Total number of cold water
cups dispensed.
– Filter Life Remaining: No. of cups or days
to go before change filter warning flashes.
– Cups this filter: Cups current filter has
dispensed.
– Start: Date unit began to be used.
– S/W: Software version installed.
—Initial setup
For use only by the installer when setting
initial operating parameters.

User guide
B–6000.
User Service
—Billi filter cartridges
The B-6000 is fitted with single dual stage
filter incorporating sediment and chemical
removal elements. All B-6000 filters are
manufactured using bacteria and biofilm
resistant materials for improved water quality.
Standard filters are certified to remove
sediment particles greater than 0.7 microns,
as well as chemicals, tastes and odours
present in the water supply. Premium
filters provide a sweeter tasting water
due to the high quality, coconut shell-
derived carbon chemical removal filter.
Rated to remove sediment particles
greater than 1 micron, these filters
have excellent chemical absorption,
removing or reducing chlorine, volatile
organic compounds (VOCs), chemicals,
tastes and odours. Special purpose filters
designed for cyst reduction and heavy
metal removal are available.
Contact Billi Pty Ltd.
Use only genuine filters as designed
for this system. All drinking water filtration
systems should be flushed after a period
of non-use. Your Billi B-6000 has an automatic
flushing cycle which can be activated.
Refer to Options, page 10. After a period
of non-use of more than two days, e.g. o
Saturday and Sunday, the cold water will
flow for 90 seconds when the time switch
first turns the unit on. Alternatively, before
use, lift the cold lever and run until water
flow stops, then release the lever.
—Filter change due monitor
The B-6000 filter change due monitor
operates by counting the number of cups
dispensed and the number of days elapsed
until a pre-set level is reached. Once reached,
the dispenser icons will briefly change to
orange once every five seconds. The B-6000
will continue to operate while the filter
indicator is flashing. Water filters installed
in areas with higher levels of turbidity
(cloudiness/sediment) will experience
a reduced service life. The flow from
the cold water outlet will decrease as the
filters become blocked. It may be necessary
to change filters before the change filter
indicator flashes. The filter monitor can be
reprogrammed to an appropriate service
interval if required. Contact Billi Pty Ltd.
Standard sub micron-rated filters
generally have a longer service life than
Premium sub micron-rated filters.
If particularly dirty water is noticed coming
through the water supply, e.g. from other tap
ware, as sometimes occurs following repairs
to local water mains, immediately turn your
Billi B-6000 o using the ON/OFF button.
This will help prevent premature blocking
of the filter cartridges.
12

13
User guide
B–6000.
—Replacement of filter cartridges
Periodic replacement of your Billi B-6000’s
Water Filter Cartridges is necessary to
maintain the sparkling cleanliness and
purity of your drinking water.
When a filter change is due, the dispenser
icons will briefly change and flash orange
once every five seconds. A ‘Filter Change Due’
message also shows in the B-6000 display.
A replacement filter change installation
service is available. To arrange, contact
your Billi representative using the phone
number showing in the display, or on page
1 of this booklet. If you wish to install the
replacement filter cartridges yourself,
your Billi representative will provide genuine
Billi replacement filter cartridge sets.
To assist with the replacement of your
B-6000 filter cartridges, a series of moving
graphic instruction screens will guide you
through the required steps. Press HELP
if display indicates ‘Filter Change Due’
or refer to Options, page 10 mode to
select ‘Filter Change Help’.
Once new filter(s) have been installed
and the filter flush cycle is complete, check
for any water leakage around the filter system.
Take particular care to ensure the area around
the water leakage sensor, located on the
lower left hand side of the bulkhead behind
the filters, is dry.
—Billi B-6000 Replacement Filters
Specifications 5 Micron Sub Micron
(standard with all systems)
Premium Sub Micron
Part number 990402 990355 990356
Suitable for: All Billi Home Systems All Billi Home Systems All Billi Home Systems
Micron Rating 5 0.7 0.2
Capacity – Litres 8,700 8,450 8,350
Unit Flow Rate – Lpm 2.5 2.5 2.5
NSF42 certified Yes Yes Yes
Retains fluoride Yes Yes No

14
User guide
B–6000.
—Filter removal and replacement instructions
1. Press or hold the “ON/OFF” Button until
the lights in the tap turn OFF.
2. Hold filter and pull towards you slowly.
The top of the filter is in a hinged cradle
assembly. It should stop after approximately
30 degrees of travel.
3. The filter can now be released from the
holding cradle by pulling down on the filter.
4. Take care not to spill water in the base of
the tray. If so wipe gently with absorbent
paper towel.
5. Install new filter(s) into the same location
by pushing all the way up into the cradle.
6. Push filter(s) forward until perpendicular
to the base and locked in place.
7. Unit will now begin an automatic flush cycle.
Tap lights will flash orange and water will
dispense from the cold side of the tap.
8. When the flush cycles finishes, the unit
will automatically reset and return to the
previous operating mode. It is normal to
see the tap lights displaying a solid red light
and a flashing blue light. This indicates that
the chilled water is currently being chilled
and should return to a solid blue light
within 5 minutes.
9. Check for any leaks from around
the filter, hosing or pipeworks.
10. Replace the front cover.
Service Codes
Your Billi B-6000 incorporates a fault detection
and diagnosis system. Should a fault occur,
a message will be displayed describing the
fault. Pressing the HELP button will advise
you of any checks that can be performed and
the phone number of your Billi service agent.
If a service call needs to be logged, note the
message displayed and report this when
booking the call. This will assist the technician
in coming prepared to rectify the problem.

15
User guide
B–6000.
Cleaning
Your B-6000 dispenser is fabricated from
robust metal with tough protective chrome
plating. Care for the dispenser as with any
chrome plated tap ware. Avoid using abrasive
cleaners. Wipe clean using a damp cloth.
Use of a non solvent, non smearing cleaner
such as Windex is recommended. Do not
pour water over the dispenser.

Billi Pty Ltd
42 Lucknow Crescent, Thomastown
Victoria 3074 Australia
Telephone [phone]
Facsimile [phone]
www.billihome.com.au
Designed and manufactured in Australia.
As Billi Pty Ltd has a policy of continual
improvement, all details are subject
to change without notice. All goods
are sold subject to our published terms
and conditions. Billi is a registered
trademark. 1211