Billi B-3000 User manual

B–3000
Instant Chilled Filtered
Water System
Installation guide

—B-3000 system components
1. Chilled water module
2. Slimline dispenser tap
3. Filter cartridge (installed)
4. Installation hardware
5. Drain connections
6. Billi B-3000 user guide
7. Warranty certificate
—Water supply
A single cold water supply is required.
Supply pressure: 200 – 1000 Kpa
Supply temperature: 5°C – 30°C
Do not install with water that is
microbiologically unsafe or with water
of unknown quality without adequate
disinfection before the system. Systems
certified for cyst reduction may
be used on disinfected water that may
contain filterable cysts.
—Power requirements
A single 10 amp standard power outlet
is required. Chiller module is supplied
with 1 metre of flex cord and plug.
—Drainage
A drainage point, such as a dishwasher
nipple or a tundish, is required. An air gap
is provided within the tap assembly.
Installation
requirements.
Diagram 1
Diagram 2
water tubing
deleted for clarity
power outlet 15mm stop-tap
(installed by plumber)
800mm
maximum
tube length
150mm
minimum
clearance
180mm
340mm
225mm
bench thicknes
s
1mm-48mm
63mm
billi mini chilled rounded dispenser dimension
s

6
mm
black
to
chille
r
d
r
ai
n
ou
t
let
22mm h
o
l
e
c
oun
t
er
t
op
o
r
si
n
k
tap s
h
a
f
t
metal
s
p
acer bus
h
b
rass
l
oc
ki
n
g
nut
1/
4”
b
l
ue
t
ube
1
0
mm
b
l
ack
t
o
d
ra
i
na
g
e po
i
nt
e
.
g
.
di
s
h
was
h
er
nippl
e
power cord
a
dapto
r
fitting
1
0
mm black
i
n
s
t
all
w
i
t
h
co
nt
i
n
uous
fall
t
o drainage point
e.g. dishwasher nipple
1
/
4” blue tube
6
mm blac
k
1/2
” stop-ta
p
(installed by
p
lumber
)
—IMPORTANT
The Billi system is recommended to be
installed on a safe tray in accordance with
AS 3500.4 Clause 4.4.
—Determine component location
A stop tap (not supplied) is to be installed
in an easily accessible position for later
service. Determine the location of each
of the components, taking into account
the tube lengths and space available.
Refer to Diagrams 1 and 2.
—Flush lines
It is important to flush lines before fitting.
Install outlet fitting to combined valve. Refer
to Diagram 4 on the following page.
—Install dispenser tap assembly
—IMPORTANT
Dispenser must not be installed below the
spill level of the receiving fixture.
A 22mm hole is required either in the
benchtop or flat surface of sink adjacent
to bowl of sink. Mount the dispenser tap.
Refer to Diagram 3.
—Install chiller module
Connect all plastic tubing as shown.
Refer to Diagram 4.
All connections are made using push-fit
connectors. Trim tubes to correct lengths.
Tubes should be cleanly cut square using
a sharp knife or plastic tube cutter.
Ensure that tube ends are round and
not flattened or kinked, then push into
connectors firmly until properly seated (to
release, press the outer ring in while pulling
gently on the tube).
—Install drain connection
The Billi dispenser tap incorporates an air
break above the spill level of the sink and
therefore a tundish is not required.
Connect a 3/8” drain tube to dishwasher
nipple, or alternative drainage point, using
fittings supplied.
—IMPORTANT
Ensure drain tube has a continual fall.
—Turn on water supply
Lift dispenser tap lever and then turn on
water supply. After water flows from outlet,
release lever and ensure that there are no
leaks. Lift lever again and run for at least 5
minutes.
—Turn on electricity supply
—Set chilled water temperature
Set the desired water temperature using
blue temperature control knob.
Refer to B–3000 User Guide.
—Re-check connections for leaks
—Explain operation to user
Installing
procedure.
Diagram 3
Diagram 4

For continued safety of this appliance
it must be installed, operated and
maintained in accordance with the
manufacturer’s instructions.
—Your appliance should be installed
by a suitably qualified tradesperson.
—For correct operation of this appliance
it is essential to observe the instructions
as outlined in this booklet.
—Filter replacement must be performed
at intervals of not more than 6 months.
—Use this appliance only as directed
in these instructions and only for its
designed purpose.
—This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
—Children should be supervised to ensure
that they do not play with the appliance.
—If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in
order to avoid a hazard.
—New hose-sets supplied with the appliance
are to be used and old hose-sets should
not be re-used.
WARNINGS.
Billi Pty Ltd
42 Lucknow Crescent, Thomastown
Victoria 3074 Australia
Telephone [phone]
Facsimile [phone]
www.billihome.com.au
Designed and manufactured in Australia.
As Billi Pty Ltd has a policy of continual
improvement, all details are subject
to change without notice. All goods
are sold subject to our published terms
and conditions. Billi is a registered
trademark. 0610