Billion BiPAC 5200 User manual

BiPAC 5200 Series
(802.11g) ADSL2+ Modem/Router
Quick Start Guide

Billion BiPAC 5200 Series ADSL2+ Modem/Router
For more detailed instructions on configuring and using
the (802.11g) ADSL2+ Modem/Router, please refer to the
on-line manual.
Package Contents
BiPAC 5200 series ADSL2+ Modem/Router
CD-ROM containing the on-line manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
AC-DC power adapter (12VDC, 1A) for BiPAC 5200 / 5200G
AC-AC power adapter (12VAC, 1A) for BiPAC 5200S
This Quick Start Guide
Warning
 Do not use the BiPAC 5200 Series in high humidity or high
temperatures.
 Do not use the same power source for the BiPAC 5200 Series as
other equipment.
 Do not open or repair the case yourself. If the BiPAC 5200
Series is too hot, turn off the power immediately and have it
repaired at a qualified service center.
 Avoid using this product and all accessories outdoors.
A
ttention
 Place the BiPAC 5200 Series on a stable surface.
 Only use the power adapter that comes with the package. Using
a different voltage rating power adaptor may damage the router.
1

Quick Start Guide
The Front LEDs
BiPAC 5200
BiPAC 5200S
BiPAC 5200G
LED Meaning
1 PPP : Lit steady when there is a PPPoA / PPPoE connection.
2 ADSL: Lit when successfully connected to an ADSL DSLAM (“linesync”).
3 LAN Port: Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps.
Blinking when data is Transmitted / Received.
4 WLAN :
(5200G
only)
Lit green when the wireless connection is established.
Flashes when sending/receiving data.
5 SYS : Lit when the system is ready.
6 PWR : Lit when power is ON.
2

Billion BiPAC 5200 Series ADSL2+ Modem/Router
The Rear Ports
BiPAC 5200
3
2 4 5
3
BiPAC 5200S
5432
BiPAC 5200G
5 4
2
1
3
Port Meaning
1 Power Switch Power ON/OFF switch
2 PWR Connect the supplied power adapter to this jack.
3 RESET
After the device is powered on, press it to reset the device or
restore to factory default settings.
0-3 seconds: reset the device
6 seconds above: restore to factory default settings (this is used
when you can not login to the router, e.g. forgot the password)
4 LAN
(RJ-45
connector)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four
LAN ports when connecting to a PC or an office/home network of
10Mbps or 100Mbps.
5 ADSL(LINE) Connect the supplied RJ-11 (“telephone”) cable to this port when
connecting to the ADSL/telephone network.

Quick Start Guide
Connecting BiPAC 5200
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR and SYS LEDs are lit steadily and that the relevant LAN LED is lit.
4

Billion BiPAC 5200 Series ADSL2+ Modem/Router
Connecting BiPAC 5200S
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR and SYS LEDs are lit steadily and that the relevant LAN LED is lit.
5

Quick Start Guide
Connecting BiPAC 5200G
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR, SYS, and WLAN LEDs are lit steadily and that the relevant LAN LED is
lit.
6

Billion BiPAC 5200 Series ADSL2+ Modem/Router
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
7

Quick Start Guide
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the Control
Panel, double-click on Network and Dial-up
Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
8