Billion BiPAC 7820NZ User manual

BiPAC 7820NZ
3G/4G LTE Embedded with
Dual- IM lots AD L2+
Wireless-N VPN Firewall Router
Quick tart Guide

Billion BiPAC 7820NZ 3G/4G LTE Embedded with Dual- IM lots AD L2+ Wireless-N VPN Firewall Router
-1-
Attention
Package Contents
BiPAC 7820NZ 3G/4G LTE Embedded with Dual- IM lots AD L2+ Wireless-N Router
CD containing the on-line manual
RJ-11 AD L/ telephone cable
Ethernet (RJ-45) cable
Two detachable antennas for 3G/4G LTE mode / one detachable antenna for 3G mode
Power adapter
Quick tart Guide
plitter/ Micro-filter (Optional)
Warning
PLEA E READ THE QUICK TART GUIDE AND FOLLOW THE
TEP CAREFULLY. THI QUICK TART GUIDE WILL HELP YOU
IN TALL THE DEVICE PROPERLY AND AVOID IMPROPER U AGE.
IF YOU NEED MORE INFORMATION ON THI OFTWARE
CONFIGURATION, PLEA E REFER TO THE U ER MANUAL ON
CD-ROM.
 Do not use the router in high humidity or high temperatures.
 Do not use the same power source for the router as other equipment.
 Do not open or repair the case yourself. If the router is too hot, turn off
the power immediately and have it repaired at a qualified service center.
 Avoid using this product and all accessories outdoors.
 Place the router on a stable surface.
 Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.

Quick tart Guide
-2-
Hardware Overview
The Front LEDs
LED STATUS DESCRIPTION
Red
Boot failure or in emergency mode.
Power
reen
System is up and ready.
reen
Transmission speed is at 10/100Mbps.
Ethernet
1- 4
Blinking
Data being transmitted/ received.
U B
reen
Connecting to a USB dongle or a hard drive.
reen
Wireless connection established.
Wireless
reen Blinking
Data being transmitted/ received.
reen blinking
WPS configuration is in progress.
WP
Off
WPS process completed or WPS is off.
reen
3 / 4 LTE service is up.
Slow Orange blinking
Weak 3 / 4 LTE signal.
Quick Orange blinking
Moderate 3 / 4 LTE signal.
3G/ 4G LTE
Solid Orange
Strong 3 /4 LTE signal.
reen blinking
DSL synchronizing or waiting for DSL synchronizing.
reen
Successfully connected to an ADSL DSLAM (Line Sync).
D L
Off
DSL cable unplugged.
reen
Having obtained an IP address successfully.
Internet
Off
Router in bridge mode or DSL connection not present.

Billion BiPAC 7820NZ 3G/4G LTE Embedded with Dual- IM lots AD L2+ Wireless-N VPN Firewall Router
-3-
Rear Panel Connectors
4G LTE mode:
3G mode:
PORT MEANIN
1
Power
Connect the supplied Power Adapter to this jack.
2
Power witch
Power ON / OFF switch.
3
Reset
After the device is powered on, press it 5 seconds or above: to restore to factory
default settings (this is used when you cannot login to the router, e.g. forgot the
password)
4
WP
By controlling the pressing time, user can achieve two different effects:
(1) WP : Press & hold the button for less than 2 seconds to trigger WPS function.
(2) Wireless ON/OFF button : Press & hold the button for more than 5 seconds to
On/Off the wireless.
Note: For WP configuration, please refer to the WP section in the User Manual.
5
IM card slots
BiPAC 7820NZ provides dual-SIM failover mobile connection with two embedded
SIM slots. Please plug SIM card into the slot.
6
U B
Connect an external USB dongle or a hard drive.
7
Ethernet
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when
connecting to a PC or an office/ home network of 10Mbps /100Mbps.
Note: Port #4 can be configured as a WAN Interface for Broadband connectivity.
8
D L
Connect this port to the DSL network with the RJ-11 cable (telephone) provided.
9
10
Antenna
(MAIN; AUX)
MAIN Jack: For 3 mode and 4 LTE mode, screw the supplied antenna onto the
MAIN antenna connector.
AUX Jack: Only for 4 LTE mode, screw the supplied antenna onto the AUX
antenna connector.
Note: 3G model comes with 1 antenna (MAIN) and 4G LTE model comes with 2
antennas (MAIN & AUX).
2
8
1
3
5
7
4
6
9
1
0

Quick tart Guide
-4-
Hardware Connection
BiPAC 7820NZ offers four modes to connect to the internet. Besides using ADSL, users can set
EWAN (Ethernet port # 4) or 3 /4 LTE for internet connection. BiPAC 7820NZ also allows
Dual WAN connection: ADSL fail-over to 3 /4 LTE, EWAN fail-over to 3 /4 LTE, ADSL
fail-over to EWAN, 3 /4 LTE fail-over to the 3 /4 LTE, and counter likewise.
AD L fail-over to 3G/4G LTE
Broadband (EWAN) fail-over to 3G/4G LTE

Billion BiPAC 7820NZ 3G/4G LTE Embedded with Dual- IM lots AD L2+ Wireless-N VPN Firewall Router
-5-
AD L fail-over to EWAN
3G/4G LTE fail-over to the 3G/4G LTE

Quick tart Guide
-6-
Hardware Installation
1. 3G/ 4G LTE Connection
Slide the SIM card into the card slot of the device with the gold contact facing down
.
Make sure that the SIM card has been slid into the bottom of the slot
with a click. When
removing the SIM card, press the SIM card again it will be ejected from the card slot.
Dual-
SIM card slots enable users to enjoy constant and seamless Internet experience by
simply plugging 3 /4 LTE SIM cards into its built-
in SIM slots without the needs of
additional 3 /4 LTE USB modems. One SIM card is active and the other is backup.
2. Power Connection
Plug in the supplied power adapter to the wall jack, the other side to the router
then
power it by pressing the Power On/Off button
. Please note that the plug type may differ
according to country. Please make sure when press Powe
r Switch the front LEDs will be
lit or off.
Warning
Please power off the device before inserting or removing
the IM card.
Attention
Connect the detachable 3G or 4G LTE antennas to the
jack (MAIN or MAIN and AUX) on the back of device as it
shows as above. Making sure they are firmly screwed in.

Billion BiPAC 7820NZ 3G/4G LTE Embedded with Dual- IM lots AD L2+ Wireless-N VPN Firewall Router
-7-
3. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the other
side to the PC’s Ethernet interface.
4. EWAN Connection
Connect RJ-45 Ethernet cable to the Ethernet port # 4 (EWAN), and connect the other
side to another alternative broadband device, such as Cable Modem, VDSL, Fibre
Modem or PON optic lines. < Please refer to User Manual for detailed instruction. >
5. AD L Connection
Connect the supplied RJ-11 phone cable to the router’s DSL port, and the other side to
the phone jack on the wall.

Quick tart Guide
-8-
6. U B Connection
FTP or Samba Server attached to the USB port. Simply plug in an external USB HD
and do a setup in the UI. <Please refer to User Manual for detailed instruction.>
7. plitter/ Micro-filter Connection
Splitter/Micro-filters are important for ADSL installation, they help ensure that
high-frequency signals are directed to the ADSL modem, and low-frequency signals
are directed to the telephone or other analog voice-channel device to prevent
inter-modulation distortion and get good speeds and stable ADSL sync rate.
a) Splitter connection
If the installation has only a single telephone and a single ADSL modem, then a splitter
can be employed.
b) Micro-filter connection
If the installation has several telephones or other analog devices then an internal
micro-filter can be employed at each analog device.

Billion BiPAC 7820NZ 3G/4G LTE Embedded with Dual- IM lots AD L2+ Wireless-N VPN Firewall Router
-9-
Connecting to the Router
1. Open the web browser and type http://192.168.1.254 in the browser's address box. This
number is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin”, and
password is “admin”. Press OK to proceed.
3. You will get a status report web page and main menu screen.
Please see the relevant sections of user manual for detailed instructions on how to
configure your router.
Troubleshooting
1. None of the LEDs are on when you turn on the router.
Check the connection between the adaptor and the router. If the error persists, you may have
a hardware problem. In this case you should contact technical support.
2. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC
connected. If it is off, check the cables between your router and the PC. Make sure you have
uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet
mask are consistent between the router and the workstations.
3. Frequent loss of AD L line sync (disconnections).
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected between them and
the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified
and licensed electrician), and ensure that all line filters are correctly installed and the right
way around. Missing line filters or line filters installed the wrong way around can cause
problems with your ADSL connection, including causing frequent disconnections. If you have
a back-to-base alarm system you should contact your security provider for a technician to
make any necessary changes.
4. Either 3G/4G LTE or wireless performance is limited.
Make sure you install the right antennas on the right jacks as mentioned in the package
contents, hardware overview and hardware installation. If it remains occur, please refer to
User manual or consult your service provider.
Product upport and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User Manual. If
you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer
where you purchased this product.
Contact Billion
WORLDWIDE
http://www.billion.com
BiPAC 7820NZ: V1.00EN