Bilt Better Homes & Gardens BHF1025004003 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2021-06-25 Rev. 0001-A
Wheaton Media Console
Stock # BHF1025004003
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
1. Please read the Assembly Instructions prior to assembling this product.
2. Remove all hardware from the box and sort by size.
3. Check to see that all hardware and parts are present BEFORE assembling.
4. Ask a friend to assist you with the assembly of this furniture.
5. To avoid damage, assemble the product on a sturdy, level and protective surface.
6. Please wait until all steps are completed before fully tightening bolts.
7. Make sure all screws and bolts are tightly fastened before the unit is used.
How to adjust the European adjustable hinges on doors
Shipping may cause doors to go out of alignment. If you find that the doors need to be adjusted slightly,
turn the appropriate screw as illustrated.
1. TO ADJUST DOOR FORWARD OR BACKWARD.
2. TO ADJUST DOOR TO RIGHT OR TO LEFT.
3. TO ADJUST DOOR UP OR DOWN.
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging material
before discarding carton. Remove any remaining staples from the carton before discarding.
Remove all parts from carton and separate into groups as indicated on part list. Please ensure all
parts are included prior to assembly. Use of power tools to complete assembly is not
recommended.
2
1
3
This product is sold with two sets of Tipping Restraint Hardware Kit. You must install the Tipping Rest
raint
Hardware between the wall and the console
to prevent any accidents or damages. When properly installed, this
restraint can provide protection against the unexpected tipping of the unit due to small tremors, bumps or
climbing. The restraint is only a deterrent and is not a substitute for proper adult supervision. Use of tip-
over
restraints may only reduce, but not eliminate, the risk of tip-over.
GE NE RAL I NF OR MA TIO N, TIP S AN D TR IC KS

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-abrasive
surface. You will need the parts identified on page 4 and 5 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH THE DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH A DAMP CLOTH.
Insert Dowel at least half-way by tapping lightly with a rubber mallet (not included), IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the pre-drilled small holes on the panel. Connect both panels together; making sure
the Cam Bolt goes into the pre-drilled hole at the end of the panel with the Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole in the panel. Make sure the arrow on the Cam Lock is
pointed towards the Cam Bolt.
3. Once the Cam Bolt is connected inside the Cam Lock, take a Phillips screwdriver (not included) and tighten
the Cam Lock clockwise.
4. Plug the Cam Lock Cover into the cross slot of the Cam Locks to conceal the cam.
You are now ready to assemble the KD unit.
XX
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Media Shelf (Qty. 1) C- Bottom Panel (Qty. 1)
D- Left Side Frame (Qty. 1) E- Right Side Frame (Qty. 1) F- Upper Partition Panel (Qty. 1)
G- Upper Partition Molding (Qty. 1) H- Lower Left Partition Panel (Qty. 1) I- Lower Right Partition Panel (Qty. 1)
J- Top Reinforced Rail (Qty. 1) K- Stretcher (Qty. 2) L- Small Adjustable Shelf (Qty. 2)
M- Large Adjustable Shelf (Qty. 1) N- Door (Qty. 2) O- Back Panel (Qty. 1)
P- Support Leg with Floor Leveler (Qty. 1) Q- Stop Rail (Qty. 1)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 32+1 extra) (Qty. 32+1 extra) (Qty. 30+1 extra)
(4) M3.5 x 15 mm Washer Head Screw (5) M4 x 38 mm Screw (6) M4 x 50 mm Screw
(Qty. 34+1 extra) (Qty. 4+1 extra) (Qty. 4+1 extra)
(7) Knob (8) 5/32” x 32 mm Knob Bolt (9) Shelf Support
(Qty. 2) (Qty. 2) (Qty. 12+1 extra)
(10) Cam Lock Cover (11) Rubber Bumper Glue
(Qty. 26+1 extra) (Qty. 4+1 extra) (Qty. 1)
Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (Qty. 2)
(Included in plastic bag)
Tools required: Phillips screwdriver and rubber mallet (not provided).