Bilt Better Homes & Gardens BHF1025004002 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2021-06-29 Rev. 0001-A
Jace Media Console
Stock # BHF1025004002
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: /
/

2
1. Please read the Assembly Instructions prior to assembling this product.
2. Remove all hardware from the box and sort by size.
3. Check to see that all hardware and parts are present BEFORE assembling.
4. Ask a friend to assist you with the assembly of this furniture.
5. To avoid damage, assemble the product on a sturdy, level and protective surface.
6. Please wait until all steps are completed before fully tightening bolts.
7. Make sure all screws and bolts are tightly fastened before the unit is used.
How to adjust the European adjustable hinges on doors
Shipping may cause doors to go out of alignment. If you find that the doors need to be adjusted slightly,
turn the appropriate screw as illustrated.
1. TO ADJUST DOOR FORWARD OR BACKWARD.
2. TO ADJUST DOOR TO RIGHT OR TO LEFT.
3. TO ADJUST DOOR UP OR DOWN.
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging material
before discarding carton. Remove any remaining staples from the carton before discarding.
Remove all parts from carton and separate into groups as indicated on part list. Please ensure all
parts are included prior to assembly. Use of power tools to complete assembly is not
recommended.
2
1
3
This product is sold with two sets of Tipping Restraint Hardware Kit. You must install the Tipping Rest
raint
Hardware between the wall and the console
to prevent any accidents or damages. When properly installed, this
restraint can provide protection against the unexpected tipping of the unit due to small tremors, bumps or
climbing. The restraint is only a deterrent and is not a substitute for proper adult supervision. Use of tip-
over
restraints may only reduce, but not eliminate, the risk of tip-over.
GE NE R AL I NFO RM AT ION , TI P S A ND TR IC KS

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-abrasive
surface. You will need the parts identified on page 4 and 5 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH THE DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH A DAMP CLOTH.
Insert Dowel at least half-way by tapping lightly with a rubber mallet (not included), IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the pre-drilled small holes on the panel. Connect both panels together; making sure
the Cam Bolt goes into the pre-drilled hole at the end of the panel with the Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole in the panel. Make sure the arrow on the Cam Lock is
pointed towards the Cam Bolt.
3. Once the Cam Bolt is connected inside the Cam Lock, take a Phillips screwdriver (not included) and tighten
the Cam Lock clockwise.
4. Plug the Cam Lock Cover into the cross slot of the Cam Locks to conceal the cam.
You are now ready to assemble the KD unit.
XX
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Media Shelf (Qty. 1) C- Bottom Panel (Qty. 1)
D- Left Side Panel (Qty. 1) E- Right Side Panel (Qty. 1) F- Left Partition Panel (Qty. 1)
G- Right Partition Panel (Qty. 1) H- Door (Qty. 2) I- Adjustable Shelf (Qty. 1)
J- Back Panel (Qty. 1) K- Left Side Frame (Qty. 1) L- Right Side Frame (Qty. 1)
M- Center Stretcher (Qty. 1) N- Support Rail (Qty. 2)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 8+1 extra) (Qty. 8+1 extra) (Qty. 16+1 extra)
(4) M4 x 50 mm Screw (5) M3.5 x 15 mm Washer Head Screw (6) 1/4” x 15 mm Bolt
(Qty. 20+1 extra) (Qty. 24+1 extra) (Qty. 12+1 extra)
(7) 1/4” x 20 mm Bolt (8) Lock Washer (9) Flat Washer
(Qty. 4+1 extra) (Qty. 12+1 extra) (Qty. 12+1 extra)
(10) 5/32” x 20 mm Handle Bolt (11) Handle (12) Shelf Support
(Qty. 4) (Qty. 2) (Qty. 4+1 extra)
(13) Cam Lock Cover (14) Rubber Bumper Glue
(Qty. 8+1 extra) (Qty. 4+1 extra) (Qty. 1)
Touch-up Pen (Qty. 1) Hex Wrench (Qty. 1) Tipping Restraint Hardware Kit (Qty. 2)
(Included in plastic bag)
Tools required: Phillips screwdriver and rubber mallet (not provided).

6
Assembly Instructions
NOTE: Please do not fully tighten all bolts/screws until you finish assembling all parts. Once assembled,
go back and fully tighten all bolts. This will make it easier during assembly of unit.
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (2) into the designated small holes on the Media Shelf (B) using a Phillips
screwdriver. DO NOT over-tighten the cam bolts.
② x 8

7
Assembly Instructions
3. Glue the Wood Dowels (3) into the inner side holes of the Side Panels (D and E) and the Partition
Panels (F and G) at both ends. Tap in with a rubber mallet, if necessary.
NOTE: It is very important to use a small amount of glue on both ends of all dowels.
③ x 16

8
Assembly Instructions
4. Align and attach both Side Panels (D and E) and Partition Panels (F and G) to the Media Shelf (B) as
shown. Tighten 8 Cam Locks (1) to secure them into place (Refer to page 3 on Cam Lock system operation
supplement).
① x 8

9
Assembly Instructions
5. Using assistance, place the Bottom Panel (C) onto the wood dowels on the vertical panels. Make sure
that the pilot holes for back panel face in the same direction.
6. Secure the Bottom Panel (C) into place by inserting eight 50 mm Screws (4) and tightening them with a
Phillips screwdriver.
④ x 8

10
Assembly Instructions
7. Ask for assistance to flip the assembled unit around at its front edges.
8. Using the pilot holes as a guide, attach the Back Panel (J) onto the back edges of the assembly. Make sure
that the overlaps on the panels are even all the way around. Secure the Back Panel (J) in place with the
15 mm Washer Head Screws (5).
NOTE: We recommend attaching back panel with the screws at the corners first.
⑤ x 24

11
Assembly Instructions
9. Fit the Support Rails (N) onto the U-shaped brackets on the Right Side Frame (L) and fasten them into
place with two 15 mm Bolts (6), two Lock Washers (8) and two Flat Washers (9).
⑥ x 2
⑧ x 2
⑨ x 2

12
Assembly Instructions
10. Attach the Center Stretcher (M) to the bottom rail of the Right Side Frame (L) with two 15 mm Bolts (6),
two Lock Washers (8) and two Flat Washers (9).
⑥ x 2
⑧ x 2
⑨ x 2

13
Assembly Instructions
11. Using assistance, flip the assembled unit around on its back edges.
12. Align and place the Right Side Frame (L) to the Right Side Panel (E).

14
Assembly Instructions
13. Repeat the same procedure to attach the Left Side Frame (K) at the opposite end. DO NOT fully tighten
the bolts.
⑥ x 4
⑧ x 4
⑨ x 4

15
Assembly Instructions
14. Orient and fit the Top Panel (A) onto the previous assembly. Make sure that the metal brackets mount
holes overlap the threaded sockets on the Side Frames (K and L) properly.

16
Assembly Instructions
15. Insert four 15 mm Bolts (6) with the Washers (8 and 9) through the metal brackets welded on the top
metal frame and screw into the Side Frames (K and L). Make sure that the offsets between the Top Panel
(A) and Side Frames (K and L) are even all the way around.
⑥ x 4
⑧ x 4
⑨ x 4

17
Assembly Instructions
16. Press and fasten Top Panel (A) to the Side Frames (K and L) with four 50 mm Screws (4).
④ x 4

18
Assembly Instructions
17. Fasten the Left Side Panel (D) to the Left Side Frame (K) using two 20 mm Bolts.
18. Repeat the same procedure to fasten the Right Side Panel at the opposite end.
⑦ x 4

19
Assembly Instructions
19. Insert eight 50 mm Screws (4) through the Support Rails (N) and securely screw into the Bottom Panel
(C).
20. Now, go back and tighten all the bolts and screws.
④ x 8

20
Assembly Instructions
21. Stand the unit upright. Pick up one Door (H) and attach the extended hinge arms to the hinge bases
installed on the Left Side Panel (D). Loosen the bolt on the back of hinge base for an easy fit. Align and
insert the “U” slot on hinge arm under the bolt head on the back of hinge base. Make sure that both door
hinges engage and function properly. Tighten the bolt on the hinge base to lock the hinges in place.
22. Repeat the same procedure to install the other Door (H) to the Right Side Panel (E).
23. Open and close the doors to make sure they are aligned and shut correctly. If necessary, adjust the screws
for a good fit. Refer to the hinge sticker on door for adjustment.