Bio Spectra 24 User manual

Radiant Heat Panel

Spectra 18, 24 and 32

User Manual

[Revision 1.0 June 2018]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY

DAMAGE AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by

this manual may vary in appearance, assembly, inclusions, specifications, description and packaging.

Radiant Heat Panel – Spectra 18, 24 and 32

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you

do not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you

do not follow instructions.

You CAN be INJURED if you

do not follow instructions or

equipment damage may occur.

It is vital that you read and understand

this user manual before using the product,

including safety warnings, and any

assembly and operating instructions.

Keep the manual for future reference.

Safety precautions and recommendations

detailed here must be fully understood

and followed to reduce the risk of injury,

fire, explosion, electrical hazard, and/or

property damage.

Safety information presented here is

generic in nature – some advice may not

be applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered

or combustion engine powered.

•Before Use - If you are not familiar with

the safe operation/handling of the

equipment, or are in any way unsure of

any aspect of suitability or correct use

for your application, you should

complete training conducted by a

person or organization qualified in safe

use and operation of this equipment,

including fuel/electrical handling and

safety.

•Do NOT operate the equipment in

flammable or explosive environments,

such as in the presence of flammable

liquids, gases or dust. The equipment

may create sparks or heat that may

ignite flammable substances.

•Keep clear of moving parts.

•Equipment may be a potential source of

electric shock or injury if misused.

•Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

•Do NOT allow others to use the

equipment unless they have read this

manual and are adequately trained.

•Keep packaging away from children -

risk of suffocation! Operators must use

the equipment correctly. When using

the equipment, consider conditions and

pay due care to persons and property.

General Work Area Safety

•Work areas should be clean and well it.

•Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

•If devices are provided for connecting

dust extraction / collection facilities,

ensure these are connected and used

properly. Dust collection can reduce

dust-related hazards.

General Personal Safety

•Wear appropriate protective equipment

when operating, servicing, or when in

the operating area of the equipment to

help protect from eye and ear injury,

poisoning, burns, cutting and crush

injuries. Protective equipment such as

safety goggles, respirators, non-slip

safety footwear, hard hat, hearing

protection etc should be used for

appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective

equipment. Do not wear loose clothing

or jewellery, which can be caught in

moving parts. Keep hair and clothing

away from the equipment.

•Stay alert and use common sense

when operating the equipment. Do not

over-reach. Always maintain secure

footing and balance.

•Do not use the equipment if tired or

under the influence of drugs, alcohol or

medication.

•This equipment is not intended for use

by persons with reduced physical,

sensory or mental capabilities.

General Fuel Safety

•Petrol/fuel/gasoline is extremely

flammable – keep clear of naked

flames or other ignition sources.

•Do not spill fuel. If you spill fuel, wipe it

off the equipment immediately – if fuel

gets on your clothing, change clothing.

•Do NOT smoke near fuel or when

refuelling.

•Always shut off the engine before

refuelling.

•Do NOT refuel a hot engine.

•Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

•Always refuel in well ventilated areas.

•Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•Using a combustion engine indoors

CAN KILL IN MINUTES. Engine

exhaust contains carbon-monoxide – a

poison you cannot smell or see.

•Use combustion engines OUTSIDE

only, and far away from windows, doors

and vents.

General Equipment Use and Care

•The equipment is designed for

domestic use only.

•Handle the equipment safely and

carefully.

•Before use, inspect the equipment for

misalignment or binding of moving

parts, loose components, damage or

any other condition that may affect its

operation. If damaged, have the

equipment repaired by an authorised

service centre or technician before use.

•Prevent unintentional starting of the

equipment - ensure equipment and

power switches are in the OFF position

before connecting or moving

equipment. Do not carry equipment

with hands or fingers touching any

controls. Remove any tools or other

items that are not a part of the

equipment from it before starting or

switching on.

•Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be

safer when used within its design and

usage parameters.

•Use the equipment and accessories

etc. in accordance with these

instructions, considering working

conditions and the work to be

performed. Using the equipment for

operations different from those

intended could result in hazardous

situations.

•Always keep equipment components

(engines, hoses, handles, controls,

frames, housings, guards etc) and

accessories (cutting tools, nozzles, bits

etc) properly maintained. Keep the

equipment clean and, where applicable,

properly lubricated.

•Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the

equipment near flammable materials,

combustible gases or liquids etc.

•The equipment is not weather-proof,

and should not be stored in direct

sunlight, at high ambient temperatures

or locations that are damp or humid.

•Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

•For specific equipment safety use and

care, see Equipment Safety.

Radiant Heat Panel – Spectra 18, 24 and 32

General Electrical Safety

•Inspect electrical equipment, extension

cords, power bars, and electrical fittings

for damage or wear before each use.

Repair or replace damaged equipment

immediately.

•Ensure all power sources conform to

equipment voltage requirements and

are disconnected before connecting or

disconnecting equipment.

•When wiring electrically powered

equipment, follow all electrical and

safety codes.

•Wherever possible, use a residual

current device (RCD).

•High voltage / high current power lines

may be present. Use extreme caution

to avoid contact or interference with

power lines. Electrical shock can be

fatal.

General Electrical Safety

•Electrically grounded equipment must

have an approved cord and plug and

be connected to a grounded electrical

outlet.

•Do NOT bypass the ON/OFF switch

and operate equipment by connecting

and disconnecting the electrical cord.

•Do NOT use equipment that has

exposed wiring, damaged switches,

covers or guards.

•Do NOT use electrical equipment in wet

conditions or in damp locations.

•Do NOT use electrical cords to lift,

move or carry equipment.

•Do NOT coil or knot electrical cords,

and ensure electrical cords are not trip

hazards.

General Service Information

•The equipment must be serviced or

repaired at authorised service centres

by qualified personnel only.

•Replacement parts must be original

equipment manufacturer (OEM) to

ensure equipment safety is maintained.

•Do NOT attempt any maintenance or

repair work not described in this

manual.

•After use, the equipment and

components may still be hot – allow the

equipment to cool and disconnect spark

plugs and/or electrical power sources

and/or batteries from it before making

adjustments, changing accessories or

performing repair or maintenance.

•Do NOT make adjustments while the

equipment is running.

•Perform service related activities in

suitable conditions, such as a

workshop.

•Replace worn, damaged or missing

warning/safety labels immediately.

Beware of Children and Pets

•Children should not be allowed to touch

or operate heaters or touch extension

cords, if used. All heaters should be

kept out of reach of children, preferably

stored or locked in a secure cabinet or

room when not in use.

Do Not Abuse the Power Cord

•Never yank or pull on the power cord to

disconnect it from the mains supply

socket. Never carry your heater by its’

power cord. Keep the power cord away

from heat, oil, solvents and sharp

edges. Check the power cord regularly

for any damage and if the power cord

becomes damaged have it replaced by

an authorised service facility.

Extension Cords and Reels

•This heater is NOT designed to run off

an extension cord. If you require an

additional power point, please have one

installed by a qualified electrician.

•The use of extension cords may cause

power voltage loss which will result in

damage to the appliance this will NOT

be covered under warranty.

Installation

•Always ensure you select the correct

fixing accessories which suit the

wall/ceiling material you are attaching

to, if in doubt please discuss with your

local retailer or local hardware store.

This heater is not designed for use

within 1m or above a water source. All

installations must meet the

requirements of Australia Standard

AS/NZS 3000:2007.

•Ensure that the heater is not positioned

directly above, below or in front of a

power point or switch.

•This heater is not designed to be used

with 3rd party timer or programmable

system.

FOR YOUR SAFETY

•WARNING: Fire risk exists if this heater

is covered by or positioned close to

curtains or other combustible materials.

•NOTE: If using this heater outside

ensure that it is connected directly to an

outdoor power point.

•The electrical system of this heater

must be connected with an automatic

30mA circuit breaker and/or residual

current device (RCD).

•If uncertain, have a qualified electrician

check your electrical system before

installation and/or use.

•All electrical connections are made in a

dry area.

•Outdoor power points must be

weatherproof and installed by a

qualified electrician.

•We are not responsible for incorrectly

chosen fixing accessories or any

damage which may be caused by an

incorrectly fitted wall heater.

•If required 15AMP power points must

be installed by a qualified electrician.

Radiant Heat Panel – Spectra 18, 24 and 32

Specific Safety Instructions

Do not use the heater in areas where there is a risk of explosion or fire from flammable

gases. Ensure that the heating area is kept clear of combustible materials. Do not use the

heater in damp areas, without suitable ventilation. This heater is not designed for use within 1m or above a

water source. Do not place within one metre (1m) of any water source. Do not place directly in front of, below

or above any power points or switches. Fire risk exists if this heater is covered by or positioned close to

curtains or other combustible materials.

•This heater is intended for domestic/household use only.

•Always ensure that this heater is installed as per the requirements noted in Australian Standard AS/NZS

3000:2007.

•Always keep heater at least one metre (1m) from combustible materials.

•DO NOT locate this heater directly below, above or in front of the power supply socket or switch.

•DO NOT use this heater within 1 metre or above any water source.

•DO NOT use this heater in either the bathroom or ensuite without suitable ventilation.

•DO NOT use a 3rd party timer, or programmable system with this heater.

•DO NOT clean the heater while the heater is on or plugged into the mains power supply.

•DO NOT touch any part of the heater while on, hot surfaces may burn.

•DO NOT use the wall heater as a dryer.

•DO NOT attempt to modify the heater, power cord, power plug or the supplied accessories in any way.

•DO NOT expose the heater to rain, water, or use in damp wet conditions.

•NEVER cover this heater.

•NEVER carry the heater by its power supply cord.

•NEVER use with the power cord coiled, bundled up or tied up. Always extend fully before use.

•NEVER use the heater if any part of it is damaged.

•Ensure that the heater is disconnected from the mains supply when installing, cleaning or

removing/installing.

•Ensure this heater is not left on when unattended.

•Ensure the heater is not used in areas where flammable gases are present, e.g. paint, petrol etc.

•Always turn the heater OFF at the unit switch and the power point switch when not in use for extended

periods of time.

•Always allow the heater to cool, about one (1) hour after the heater has been turned off, before cleaning

the heater.

•Always ensure that the power cord is fully extended and NOT in contact with any part of the heater.

•Always ensure that the heater is kept clean and free from dust.

•Only use this heater when securely attached to the wall/ceiling.

Electrical Data

This product is fitted with a sealed electrical connection plug that is compatible with the heater, the

mains supply for Australia and meets the requirements of international standards. This heater must

be connected to a supply voltage that is equal to that stated on the rating label. If the mains connection plug

or power cord becomes damaged it must be replaced with a complete assembly that is identical to the

original, and this must be replaced by an authorised service centre. Always follow the Australian

requirements for connection to the mains supply. If in doubt always consult a qualified electrician. Note:

(3200W) requires installation of a 15AMP socket by a qualified electrician before use.

Radiant Heat Panel – Spectra 18, 24 and 32

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on

your product and their meanings. If any stickers become unreadable, unattached etc, replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and

open flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc

before using the product.

Use Hand Protection

Wear appropriate hand

protection and take due care

as the product or use of the

product may present hand

hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be

fatal.

Electrocution / Electrical

Shock Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling

electrical products, cables,

plugs and leads. Electrical

shock can be fatal.

Toxic Fumes / Dust Hazard

Using the product or by-

products from use may

produce fumes, smoke or

particles that could be harmful

if inhaled. Wear appropriate

breathing protection and have

adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be

present. Avoid ignition sources

and open flames. Danger of

explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices

that can cause severe cut

injury to fingers, limbs etc.

Take due care when handling

and using the product.

Crush Hazard

The product may have blades,

edges or mechanical devices

that can cause severe crush

injury to fingers, limbs etc.

Take due care when handling

and using the product.

Single Operator Only

The product must be operated

by a single person only. More

than one person operating the

product may introduce

additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care

as the product or use of the

product may present face and

eye hazards.

Use Foot Protection

Wear appropriate foot

protection and take due care

as the product or use of the

product may present foot

hazards.

Use Eye / Ear / Head

Protection

Wear appropriate eye and / or

ear and / or head protection

and take due care as the

product or use of the product

may present eye, hearing and

head hazards.

Running Hazard

Do not run on or near the

product as doing so may

present a fall hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or

objects that can cause severe

injury to fingers, limbs, blood

etc. Take due care when

handling and using the

product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures

and hot surfaces that can

cause burn injuries.

Flying Debris Hazard

Be aware that the product or

use of the product may

present hazards produced by

flying debris. Wear appropriate

clothing and protectiove

devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts

to stop fully before handling

the product, adjusting,

maintenence etc.

Radiant Heat Panel – Spectra 18, 24 and 32

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be

fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due

care when handling and using

the product.

Slope / Fall Injury Hazard

Be aware that using the

product on sloping surfaces or

in slippery conditions may

present additional dangers

from falls and contact with

blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

maneouvres as this may result

in severe injury due to falling,

product breakage or collapse

etc.

Electrocution / Electrical

Shock Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do

NOT use in rain, damp or wet

conditions. Electrical shock

can be fatal.

Electrocution / Electrical

Shock Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product.

Always disconnect the product

from the electrical supply

before handling the product,

adjusting, maintenence etc.

Power Line Electrocution

Hazard

High voltage / high current

power lines may be present.

Use extreme caution to avoid

contact or interference with

power lines. Electrical shock

can be fatal.

"Kick-Back" Hazard

High level of "kick-back"

hazard that can cause the

machine to suddenly rotate

towards operator. Kick-back

injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch

to move people.

Winch Lift Hazard

Do NOT LIFT load vertically.

Use machine to PULL only.

Cable Hazard

Ensure that load bearing cable

is not kinked or knotted.

Winch Cable Hazard

Ensure that there is a

minimum number of cable

coils on winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye

protection for welding. Dorect

exposure to weld arcs may

cause permanent eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser, or allow

others to.

Radiant Heat Panel – Spectra 18, 24 and 32

Table of Contents

Safety...................................................................................................................................................2

Specific Safety Instructions........................................................................................................................4

Electrical Data............................................................................................................................................4

Safety Symbols ..........................................................................................................................................5

Assembly ............................................................................................................................................8

Heater Head...............................................................................................................................................8

Mounting Heater ........................................................................................................................................8

General Mounting Suggestions ...........................................................................................................8

Wall/Ceiling Bracket Assembly ............................................................................................................8

Adjusting the Bracket Position ...................................................................................................................9

Tilting the Head.......................................................................................................................................... 9

Heater Positioning.................................................................................................................................... 10

Operation ..........................................................................................................................................11

Maintenance .....................................................................................................................................11

Specifications...................................................................................................................................12

Spectra 18................................................................................................................................................12

Spectra 24................................................................................................................................................12

Spectra 32................................................................................................................................................12

Radiant Heat Panel – Spectra 18, 24 and 32

Assembly

Heater Head

Attach the heater rear bracket (B) to the heater body (A) using bolts, washers and nuts. You can either

mount side or lengthways depending on the mounting surface.

Mounting Heater

General Mounting Suggestions

If unsure, please discuss with your local hardware store.

•Ensure the fixing screws are at least suitable for 10Kg each.

•If fitting to a stud wall or ceiling, ensure all fixing screws are into timber. Plasterboard IS NOT suitable by

itself.

•If no timber stud/joists are available we would suggest installing a timber batten to attach to.

Wall/Ceiling Bracket Assembly

1. The bottom of the heater body should be 1.8m above the floor, see Heater Positioning.

2. Do not position the heater directly above or below a power point or switch. Do not position heater in front

of a power point.

3. Mark and drill 2 mounting holes for bracket (C).

4. Using 2 suitable screws (not supplied) attach the bracket to the wall or ceiling.

Note: If unsure what screws to use, please discuss with your local hardware store.

5. Using the nuts and bolts join the bracket (C) to the heater bracket (B) and tighten fully.

6. Heater is now mounted and ready for use. Check the safety distance between the heater body and

flammable surface when wall or corner mounted. Do not mount the heater in the ceiling, always mount to

the ceiling, see Heater Positioning.

BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO

Radiant Heat Panel – Spectra 18, 24 and 32

Adjusting the Bracket Position

Tilting the Head

Always ensure that the heater is

switched off, disconnected from the

mains power supply and is cold to touch. If

heater has been recently used, please leave the

wall heater one (1) hour to cool before tilting

head.

1. Loosen the locking bolt and remove.

2. Loosen the head tilt bolt, do not remove.

3. Head can be tilted through 30°.

4. Tighten the head tilt bolt when the desired

angle is achieved.

5. Insert and tighten the locking bolt if possible

to stop any unintentional movement of the

heater.

Note: If locking bolt cannot be fitted, ensure

the head tilt bolt is very tight.

BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO

Radiant Heat Panel – Spectra 18, 24 and 32

Heater Positioning

1. Position heater at least 200mm from the eave lining or ceiling or wall at 90° to heater.

2. Position heater at least 1.8m above the floor.

3. Never position in front, above or below a power point.

4. If heater is facing another vertical surface, e.g. a wall, the gap must be at least 1 metre.

5. Never mount heater within 1 metre of a water source, e.g. a tap.

Never mount heater into the wall or ceiling. Only mount to the surface.

BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO

Radiant Heat Panel – Spectra 18, 24 and 32

Operation

1. Plug into a 240V AC wall socket.

2. To turn ON – switch the wall socket on.

3. Turn OFF – switch the wall socket off.

4. Unplug lead from wall socket when not in use.

The heater (3200W) is a 15AMP electric heater. This requires a special 15AMP power socket to be

installed by a qualified electrician before being able to use.

Maintenance

Always ensure that the wall heater has been left for one (1) hour to cool before cleaning.

1. Turn off and disconnect from mains power, allow to cool.

2. Wipe unit over with a damp, clean, soft lint-free cloth.

3. For stubborn marks, you can use a mild dish washing solution on a damp, clean, soft, lint-free cloth.

NEVER allow water or a mild dish washing solution to enter or drip onto the wall heater.

NEVER use solvents, e.g. Petrol, Toluene, Methylated Spirits etc. to clean the floor heater, as these

will damage the surface finish and may cause a fire when unit is next used.

BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO

Radiant Heat Panel – Spectra 18, 24 and 32

Specifications

Spectra 18

Power 1800W

Material Anodised Aluminium

Input Voltage 240V AC

IPx4 rated Splash Resistant

Cord Length 1.5m

Plug Standard 3 pin 15 Amp

Power Plug Australian Standard

Spectra 24

Power 2400W

Material Anodised Aluminium

Input Voltage 240V AC

IPx4 rated Splash Resistant

Cord Length 1.5m

Plug Standard 3 pin 15 Amp

Power Plug Australian Standard

Spectra 32

Power 3200W

Material Anodised Aluminium

Input Voltage 240V AC

IPx4 rated Splash Resistant

Cord Length 1.5m

Plug Standard 3 pin 15 Amp

Power Plug Australian Standard

NOTE: The 3200W Bio Electric Radiant Strip Heater requires installation by a licensed electrician to a 15A

circuit

BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO BIO

Radiant Heat Panel – Spectra 18, 24 and 32

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety

Consult all documentation, packaging

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.

Before each use, check the product for

loose/broken/damaged/missing parts,

wear or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear or leaks.

Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.

Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.

The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.

This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business

or employee, or financially affect the user, business or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement or service by a technician

may cause financial loss, loss of employee time or an

inconvenience requiring compensation.

If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

Bio Spectra 24 User manual

Popular Electric Heater manuals by other brands