Biocare VTRUST 701DH User manual

Quick Start Guide
Press the “Start/Stop/Stat” button to start a measurement.
The monitor might take second measurement when detect
an unexpected motion signal during the first measurement
period.
Press the “Start/Stop/Stat” button for 3 seconds to activate
the “Stat” measurement mode. VTRUST 701DH will continue
measure the blood pressure within 5 minutes during
“Stat measurement mode”.
Measurement Mode
LCD Drawing
Stat Measurement Mode
Monitor Front View
2
3
4
5
6
7
Power on/off key
Warning silence key
Cycle time key
Review key
Monitor Front View Key Function
○ Press briefly to turn power on.
○ Press and hold for 3 seconds to turn power off.
○ Press this key for silence.
Press this key to review stored data.
Press this key momentarily to activate the NIBP cycle time menu.
Press key again, a second time, to step through cycle time selctions.
○Red light : Indicates when approximately one hundred NIBP
measurements remain. If battery power falls below a level consistent
with reliable operation, the device will automatically turn off.
The battery must then be recharged.
○ Orange light : Connecting the battery charger with the device and
the batteries are charging.
○ Green light : The batteries are fully charged.
Systolic pressure
Mean arterial pressure
Battery status indicator
8
9
10
11
12
13
14
LCD display
Diastolic pressure
Heart Rate
NIBP Start/
Stop/Stat
Up key
Setup key
Down key
Monitor Front View Key Function
Press this key to setup the functions or parameters.
Press this key to scroll up through sub selections.
Press this key to scroll down through sub selections.
○ NIBP measurement start key.
○ Press the key again to cancel a NIBP measurement.
○ Press and hold the key for 3 secs the monitor in STAT mode.
Systolic pressure measurement
Mean arterial pressure measurement
LCD display
Diastolic pressure measurement
Heart Rate measurement
Handheld Non-Invasive Blood
Pressure (NIBP) Monitor
701DH
start
Date
Time
Review Data
Warning Silence
USB Connecting
Measurement Mode
BP Unit
Pulse Rate Unit
Measure/Memory Sequence
Pulse Rate Symbol
Warning Linit Range
Cycle Time

18~26cm10~19cm 25~35cm 33~47cm
Cycle Time Function Recommend Cuff Site
4F, No. 12, Lane 5, Sec. 2, Nanshan Rd., Lujhu
Township, Taoyuan County 33852, Taiwan
TEL: [phone]
FAX: [phone]
www.biocare.com.tw
Press the “Cycle time” function button to select the desire
measurement period. And press the “Start/Stop/Stat”
button to start the cycle time measurements.
Cuff Size Selection
Wrap Cuff Correctly
◎Infant blood pressure cuff (10-19cm)
◎Small adult blood pressure cuff (18-26cm)
※Adult blood pressure cuff (25-35cm)
◎Adult extra long blood pressure cuff (25-35cm)
◎Large adult blood pressure cuff (33-47cm)
The end of the cuff (marked by an index line) should fall
inside the range marked clearly on the inside of the cuff.
If not, use a different size cuff. If the cuff is in the upper
limit of the cuff range, the next larger size cuff can be
used to ensure accurate measurements.
VTRUST 701DH Provides 5 sizes of cuffs. In order to get
the correct blood pressure reading, It is very importand to
select the appropriate cuff.(※Standard Accessory).
Cuff Size
For measurement accuracy, the patient should
keep the cuffed part of the arm at the same level as the
heart. NIBP measurement points above the level of the
heart gives reduced pressure values. Measurement points
below the heart level gives increased values. These errors
are due to the weight of the blood.
The cuff shown below on the left is too small for the arm,
therefore,full cuff pressure is never applied to the artery.
This causes an erroneously high blood pressure reading.
The cuff shown on the right is of adequate width for the
arm, and full cuff pressure is applied to the brachial artery.
Cuffs for thighs are available for large patients or those
where neither arm is available for cuff placement. Blood
pressure measured at the thigh is typically 20-30 mmHg
higher (when the patient is standing, not prone) than blood
pressure measured at the upper arm.
9010123