BIOS DVT12S2 User manual

Quick Installation Guide
−SAS6G model −
Quick Installation Guide
−SAS6G model −
DVT12S2
DVT12S2
This Quick Installation Guide(QIG) describes the packing content and
installation guide line for DVT12S2 model.
BIOS and its resellers are not liable for any
data or information lost or possible software
issue to use the product. We do not take any
responsibility of damage and/or systemmalfunc-
tion due to our product / storage device failure
or for any of the problems caused as a result It
is recommended to always backup your data.
◆Introduction
Attention
Compact and Large Capacity Desktop SAS JBOD
Up to 12 Hot-swappable 3.5” SAS or SATA Drives
DVT12S2 Quick Installation Guide – SAS 6G model-
DVT12S2model
Dec 2013 Printing No:DVT12S2_QIG01
Producer Yonezawa Shigeru
Publisher BIOS AP Inc.
)$1R6HF1HZ7DLSHL%OYG;LQ]KXDQJ'LVW
1HZ7DLSHL&LW\7DLZDQ
TEL: [phone] FAX: [phone]
Email: [email protected] Website: www.biosap.com.tw
Warranty Information
VT12S2 d l

◆Packing List
The box should contain the DVT12S2 and below accessories:
DVT12S2 Body DVT12S2
Quick Installation Guide
Power cable
◇Packing List
Ɣ'976%RG\
ƔPower cable
ƔPLQL6$6FDEOH0HWHU
Ɣ4XLFN,QVWDOODWLRQ*XLGH7KLVGRFXPHQW
◆Name and Function of each part
＜DVT12S2Front ＞
①POWERButton
 PowerON/OFFSwitch
②POWERLED
 BLUE:On,powerupindication

③
HDDAccess/Fail*
LED
BLUE:On,diskdriveinserted
BLUEFlash:DriveActivity
AmberON:DriveFail,Locate,orRebuild
AmberLEDdependsonRAIDorHBAimplementation
④SystemFailLED
 AmberON:Indicateanysystemfailsuch
asovertemperature,fanfailorexpanderfail
⑤FanFailLED
 InternalFan1orFan2Fail.RefertoHBA,RAIDGUI
⑥MuteButton
 Turnoffthebuzzeralarm


⑦miniSASHost
 SFF8088connectorforHostconnection
⑧miniSASExpansion
 SFF8088connectorforExpansion

⑨PowerInlet
 ACPowerInlet,FullrangeAC90-260V
Begin to use
1.Find the miniSAS cable inside the package connecting it to miniSAS
RI+RVW+%$RU5$,'+%$5HIHUWRQH[WSDJHUHDUYLHZRIWKHHQFORVXUH
2.Connect power cord to the AC inlet
3.Push power button at front side of the chassis
4.Power on your host computer and start to configure your RAID HBA
5.If you had more than one DVT12S2 to cascade,
connect the expansion port to the host of next DVT12S2.

For Disk drive installation if needed,
Follow the below instruction to install or replace a disk drive.
Step 1.
Loosen the left side rear screws
UHDUYLHZDQGRSHQWKHVLGHSDQHO
Step 2.
Use hand or screw driver to loosen
the thumb screw of disk drive tray.
Step 3.
Prepare a flat operating table for following operation.
Put the disk drive perpendiculous to the flat table with the drive connector
WRZDUGERWWRPGULYHFRQQHFWRUVLGHIDFLQJ\RX
With thumb screw of drive tray on left hand side, slide down the tray carefully
till it touches down the flat table.
Step 4.
Get four screws from the screw bag
and tightly screw them all
◆Installation Guide
③
④
⑤
⑥
①
②
＜DVT12S2Rear
＞
⑧⑦
⑨
Drive numeration label is attached
on side panel as below.
PLQL6$6FDEOH0HWHU
Quick Installation Guide
−SAS6G model −
DVT12S2
This Quick Installation Guide(QIG) describes the packing content and
installation guide line for DVT12S2 model.
BIOS and its resellers are not liable for any
data or information lost or possible software
issue to use the product. We do not take any
responsibility of damage and/or systemmalfun c-
tion due to our product / storage device failure
or for any of the problems caused as a result It
is recommended to always backup your data.
◆Introduction
Attention
Compact and Large Capacity Desktop SAS JBOD
Up to 12 Hot-swappable 3.5” SAS or SATA Drives
DVT12S2 Quick Installation Guide – SAS 6G model-
DVT12S2model
Quick Installation Guide
DriveFaultLEDscanalsobefoundonbackplaneforeachdrivewhenchassisisopenedfordrivereplacement