Biostar P4VMA-M Operating and installation instructions

11
11
1EnglishEnglish
EnglishEnglish
English
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
Any changes or modification made to this equipment void the user’s authority
to operate this equipment.
This equipment generates, uses, and radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
* All external cables connecting to this basic unit must be shielded.
C. D. C. Statement
ThisdigitalapparatusdoesnotexceedtheClassBlimitsforradionoiseemissions
from digital apparatus as set out in the radio interference regulations or the Canadian
Department of Communications.
CE Mark
This equipment is in conformity with the EMC directive.

22
22
2
EnglishEnglish
EnglishEnglish
English
Overview
The information in this document is subject to change without notice and
should not be construed as a commitment by the manufacturer.
The manufacturer assumes no responsibility for any errors that might appear
in this document.
The software described in this document is furnished under a license and may
be used or copied only in accordance with the terms of such license. No responsibility
is assumed for the use or reliability of software or equipment that is not supplied by the
manufacturer or its affiliated companies.
Copyright Notice
No part of this manual may be reproduced or transmitted in any form or by any
means, electronic or mechanical, photocopying, recording or otherwise, stored in any
retrieval system of any nature without the prior written permission of the manufacturer.
Trademark
Other product and company names mentioned herein may be trademarks and/
or service marks of their respective owners.
Intel and Pentium are registered trademarks of Intel Corporation.
Nvidia and nforce is registered trademark of Nvidia.
Sis is registered trademark of Silicon Integrated Systems Corporation.
PS/2 is registered trademark of International Business Machines Corporation.
VIA is registered trademark of VIA Technologies, Inc.
ATI is registered trademark of ATI Technologies, Inc.
AMD is registered trademark of Advanced Micro Devices, Inc.

33
33
3EnglishEnglish
EnglishEnglish
English
Important Safety Information
1. Please read these safety instructions carefully.
2. Please keep this User’s Manual for later reference.
3. Please disconnect this equipment from AC outlet before cleaning. Don’t use
liquid or sprayed detergent for cleaning. Use moisture sheet or clothe for
cleaning.
4. For pluggable equipment, the socket-outlet shall be installed near the equipment
and shall be easily accessible.
5. Please keep this equipment from humidity.
6. Lay this equipment on a reliable surface when install. A drop or fall could cause
injury.
7. Do not leave this equipment in an environment unconditioned, storage
temperature above 40°C, it may damage the equipment.
8. The openings on the enclosure are for air convection hence protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
9. Make sure the voltage of the power source when connect the equipment to the
power outlet.
10. Place the power cord such a way that people can not step on it. Do not place
anything over the power cord. The power cord must be rated for the product
and for the voltage and current marked on the product’s electrical ratings label.
The voltage and current rating of the cord should be greater than the voltage and
current rating marked on the product.
11. All cautions and warnings on the equipment should be noted.
12. If the equipment is not use for long time, disconnect the equipment from mains
to avoid being damaged by transient over-voltage.
13. Never pour any liquid into ventilation openings, this could cause fire or electrical
shock.
14. Never open the equipment. For safety reason, qualified service personnel
should only open the equipment.
15. If one of the following situations arises, get the equipment checked by service
personnel:
a. The Power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment has not work well or you can not get it work according to
user’s manual.
e. The equipment has dropped and damaged.
f. If the equipment has obvious sign of breakage

44
44
4
EnglishEnglish
EnglishEnglish
English
Table of Contents
FCC Statement....................................................................... 1
C. D. C. Statement ............................................................................... 1
CE Mark .............................................................................................. 1
Overview ................................................................................ 2
Copyright Notice................................................................................. 2
Trademark ........................................................................................... 2
Important Safety Information ............................................ 3
English
Section 1. Layout of P4VMA-M V.2.x ........................................... 5
Section 2. Layout of P4VMA-M V.7.x ........................................... 6
Section 3. P4VMA-M System Structure ........................................ 6
Section 4. P4VMA-M Features ....................................................... 8
A. Hardware ............................................................................... 8
B. BIOS & Software .................................................................... 9
Section 5. Package contents .......................................................... 10
Section 6. Installation and Setup ................................................. 11
Francais
Caracteristiques de P4VMA-M.................................................... 19
Trouble Shooting................................................................ 22
WarpSpeederTM..................................................................................................................... 24
StudioFun!TM (Optional) .................................................... 32

55
55
5EnglishEnglish
EnglishEnglish
English
Section 1. Layout of P4VMA-M V.2.x
NOTE: “ ” represents the first pin.
BIOS
BAT1
IDE1
IDE2
FDD1
DIMM1
JVGA1
JCOM1
JKBMS1
JSPDIFO1
JUSBV3
1
JUSB4
1
JCMOS1
1
JUSBV1
1
JWOM1
1JSFAN1
1JPANEL1
1
24
2
CNR1
PCI1
PCI2
PCI3
CODEC
J1394A1
JCDIN1
JCFAN1
1
1
JAUDIO1
114
1
JKBV1
JDJ1
1JCI1
1
IEEE1394
VIA
VT6307
SuperI/O
IT8705
JCOM2-HEADER
AGP1
PM800
VT8237
JUSBV2
1
11
Socket478 CPU1
12
910
JUSB3
19
923
19
1
16
JGAME1 JWOL1
1
JSATA2
JSATA1
1
1
JNFAN1
1
CODEC
BIOS
J1394_USB1
JUSBLAN1
JAUDIO
1JFM1
1
RTL8100C
1

66
66
6
EnglishEnglish
EnglishEnglish
English
Section 2. Layout of P4VMA-M V.7.x
NOTE: “ ” represents the first pin.
(Optional)
BIOS
BAT1
IDE1 IDE2
FDD1
DIMM1
JVGA1
JCOM1
JUSB1
JUSBLAN1
JKBMS1
JAUDIO
JSPDIFO1
JUSB4
1
JCMOS1
1
JSFAN1
1JPANEL1
124
2
CNR1
PCI1
PCI2
PCI3
CODEC
JCDIN1
JCFAN1
1
1
JAUDIO1
114
JCI1
1
SuperI/O
IT8705
1
AGP1
PM800
VT8237
1
11
Socket 478 CPU1
JUSB3
19
9
23
VT6103
JSATA2
JSATA1
1
1
CODEC

77
77
7EnglishEnglish
EnglishEnglish
English
Section 3. P4VMA-M System Structure
CPU+Socket478
PM800
VT8237
AGP4X/8X
CRT DDR200/266/333/400
8 USB2.0 AC’97
ATA66/100/133
IDE1/IDE2
3 PCI Master ITE I/O
Floopy/Printer/Keyboard/Mouse
BIOS
10Mb/s, 100Mb/s
LAN
VT6103 (for v7.x)/
RTL8100C(for v2.x)

88
88
8
EnglishEnglish
EnglishEnglish
English
Section 4. P4VMA-M Features
In this section, you shall find all the information about the
motherboard in your computer, including its features, various
jumpers, headers, connectors, and also the installation guide to
help you a quick and correct installation of your system.
A. Hardware
CPUCPU
CPUCPU
CPU
* Supports Socket 478.
* Supports the Intel®Pentium 4
Processor.
* Supports the Intel®Pentium 4
478-pin Prescott CPU.
* Front Side Bus at 400/533/800 MHz.
ChipsetChipset
ChipsetChipset
Chipset
* North Bridge: VIA PM800
* South Bridge: VIA VT8237
Super I/OSuper I/O
Super I/OSuper I/O
Super I/O
* Chip: ITE IT8705F
* Provides the most commonly used
legacy Super I/O functionality.
* Environment Control initiatives,
- H/W Monitor
- Fan Speed Controller (optional)
- ITE's “Smart Guardian” function
SlotsSlots
SlotsSlots
Slots
* Three 32-bit PCI bus master slots.
* One AGP 4X/8X compatible slot.
* One CNR slot. (optional)
LAN PHY(optional for v7.x)LAN PHY(optional for v7.x)
LAN PHY(optional for v7.x)LAN PHY(optional for v7.x)
LAN PHY(optional for v7.x)
* Chip: VT6103
* Support 10 Mb/s, 100 Mb/s auto-
negotiation operation.
* Half/Full duplex capability.
* Supports ACPI, PCI power
management.
On Board IDEOn Board IDE
On Board IDEOn Board IDE
On Board IDE
* Supports four IDE disk drives.
* Supports PIO Mode 4, Block Mode
and Ultra DMA 33/66/100/133 Bus
Master Mode.
IEEE 1394 Chip (Optional)IEEE 1394 Chip (Optional)
IEEE 1394 Chip (Optional)IEEE 1394 Chip (Optional)
IEEE 1394 Chip (Optional)
* Chip: VIA VT6307.
* Supports 2 ports with transferrate
up to 400Mb/s.
On Board ACOn Board AC
On Board ACOn Board AC
On Board AC’97 Sound97 Sound
97 Sound97 Sound
97 Sound
CodecCodec
CodecCodec
Codec
* Chip: CMI9739A/9761A.
* Compliant with AC’97
specification.
* AC’97 2.2 interface (for
CMI9739A)/AC’97 2.3 interface
(for CMI9761A)
* Supports S/PDIF-Out.
* Supports 6 channels.
* Supports stereo microphone (for
CMI9761A).
LAN (for v2.x)LAN (for v2.x)
LAN (for v2.x)LAN (for v2.x)
LAN (for v2.x)
* Chip: RTL8100C/RTL8110S
* Support 10 Mb/s, 100 Mb/s
(1000Mb/s for RTL8110S) auto-
negotiation operation.
* Half/Full duplex capability.
* Supports ACPI, PCI power
management.

99
99
9EnglishEnglish
EnglishEnglish
English
Main MemoryMain Memory
Main MemoryMain Memory
Main Memory
* Supports up to two DDR devices.
* Supports 266/333/400 MHz DDR devices.
* Maximum memory size is 2GB.
Total Memory Size with Unbuffered DIMMs
On Board PeripheralsOn Board Peripherals
On Board PeripheralsOn Board Peripherals
On Board Peripherals
a. Rear side
- 1 x serial port.
- 1 x Parallel Port, 1 x VGA Port
- 1 x Audio ports in vertical.
- 1 x RJ-45 LAN jack.
- 1 x PS/2 mouse and PS/2 keyboard.
- 4 x USB2.0 ports.
- 1 x IEEE 1394 FirewireTM port
(optional)
DimensionDimension
DimensionDimension
Dimension
* Micro ATX Form Factor: 24.4 cm x 24.4 cm. (W x L) (for version 2.0)
* Micro ATX Form Factor: 19.9 cm x 24.4 cm. (W x L) (for version 7.x)
B. BIOS & Software
BIOSBIOS
BIOSBIOS
BIOS* Award legal BIOS.
* Supports APM1.2, ACPI, USB Function.
* The BIOS configuration manual can be found in the Setup Driver CD.
SoftwareSoftware
SoftwareSoftware
Software
* Supports WarpspeederTM, 9th TouchTM, FLASHERTM, BootblockerTM,
WinFlasherTM and StudioFun!(Optional)
* Offers the highest performance for Windows 98SE, Windows ME, Windows
2000, Windows XP, Linux, UNIX series, etc.
tekcoSMMID noitacoL eludoMRDD eziSyromeMlatoT )BM(
1AMMID /BM215/BM652/BM821/BM46 1*/BG1 BG2sixaM
1BMMID /BM215/BM652/BM821/BM46 1*/BG1
b. Front Side
- 1 floppy port supports 2 FDDs with
360K, 720K, 1.2M, 1.44M and
2.88Mbytes.
- 4 x USB2.0 ports.
- 1 S/PDIF-Out connector (optional)

1010
1010
10
EnglishEnglish
EnglishEnglish
English
Section 5. Package contents
CheckwhatyouhaveboughtbeforeyoustartyourDIYaction.
If there are anything missing, please contact your dealer
immediately.
* HDD Cable X 1
* FDD Cable X 1
* User's Manual X1
* USB 2.0 Cable X1 (optional)
* Rear I/O Panel for ATX Case X1 (optional)
* Fully Setup Driver CD X1
* StudioFun! Application CD X1 (optional)
* S/PDIF-Out Cable X 1 (optional)
* IEEE 1394 Cable X 1 (optional)
* Serial ATA Cable X 2 (optional)

1111
1111
11 EnglishEnglish
EnglishEnglish
English
Section 6. Installation and Setup
In this section, you will learn how to install the CPU, DDR
Module, and also how to set up jumpers and all the information
about the components on the motherboard. Not only can you find
the installation steps, but also the details and locations of the
components on the motherboard.
1. CPU Installation1. CPU Installation
1. CPU Installation1. CPU Installation
1. CPU Installation
The motherboard supports the Intel Pentium®Socket-478 processor. When
you are installing the CPU, make sure the CPU has a cooling fan attached on the right
to prevent overheating. If you do not find the cooling fan, contact your dealer and make
sure to install them before turning on the computer.
Step1: Pull the lever sideways away from the socket and then raise the
lever up to a 90-degree angle.
Step2: Look for the white dot/cut edge. The white dot/cut edge should
point towards the lever pivot. The CPU will fit only in the cor-
rect orientation.
Step3: Hold the CPU down firmly, and then close the lever.
Step4: Put the CPU fan on the CPU and buckle it. Connect the CPU fan
power cable to the JCFAN1. This completes the installation.
2 Central Processing Unit: CPU2 Central Processing Unit: CPU
2 Central Processing Unit: CPU2 Central Processing Unit: CPU
2 Central Processing Unit: CPU
These fan headers support cooling fans built in the computer. The fan wiring and
plug may be different according to the fan manufacturer. Connect the fan cable to the
connector while matching the black wire to the pin 1.
(1) CPU Fan Headers: JCFAN1 Pin Assignment
1 Ground
2 +12V
3 FAN RPM Rate Sense
1

1212
1212
12
EnglishEnglish
EnglishEnglish
English
(2) System Fan Headers/North Bridge Fan Header: JSFAN1/(JNFAN1: optional)
Pin Assignment
1 Ground
2 +12V
3 FAN RPM Rate Sense
3. Installing DDR Module3. Installing DDR Module
3. Installing DDR Module3. Installing DDR Module
3. Installing DDR Module
1. Unlock a DIMM slot by
pressing the retaining clips
outward. Align a DIMM to the
slot in the way that the notch
of the DIMM matches the
break of the slot.
2. Insert the DIMM firmly and
vertically into the slot until the
retainingchipsnapback in place
and the Dimm is properly
seated.
4. How to set up Jumpers?4. How to set up Jumpers?
4. How to set up Jumpers?4. How to set up Jumpers?
4. How to set up Jumpers?
The illustration shows how to set up jumpers. When the Jumper cap is placed
on pins, the jumper is “close”. If no jumper cap is placed on the pins, the jumper is
”open”. The illustration shows a 3-pin jumper whose pin 1 and 2 are “close” when
jumper cap is placed on these 2 pins.
Jumper open Jumper close Pin1-2 close
5. Jumpers, Headers, Connectors & Slots:5. Jumpers, Headers, Connectors & Slots:
5. Jumpers, Headers, Connectors & Slots:5. Jumpers, Headers, Connectors & Slots:
5. Jumpers, Headers, Connectors & Slots:
(1) Floppy Disk Connector: FDD1
The motherboard provides a standard floppy disk connector that supports
360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector
supports the provided floppy drive ribbon cables.
1

1313
1313
13 EnglishEnglish
EnglishEnglish
English
(2) Hard Disk Connectors: IDE1/ IDE2
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/ 66/ 100/ 133 functionality. It has
two HDD connectors IDE1 (primary) and IDE2 (secondary).
The IDE connectors can connect a master and a slave drive, so you can connect
up to four hard disk drives. The first hard drive should always be connected to
IDE1.
(3) Peripheral Component Interconnect Slots: PCI1-3
This motherboard is equipped with 3 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designed as 32 bits.
(4) Accelerated Graphics Port Slot: AGP1
Your monitor will attach directly to that video card. This motherboard supports
video cards for PCI slots, but it is also equipped with an Accelerated Graphics
Port (AGP). An AGP card will take advantage of AGP technology to improve
video efficiency and performance, especially with 3D graphics.
(5) Communication Network Riser Slot: CNR1 (optional)
The CNR specification is an open Industry Standard Architecture, and it defines
a hardware scalable riser card interface, which supports modem only.
(6) Clear CMOS Jumper: JCMOS1
This jumper helps you to clear the Real Time Clock (RTC) Ram in CMOS. You
can erase the CMOS RTC Ram data to clear the CMOS memory of date, time,
and system setup parameters.
JCMOS1 Assignment
Pin 1-2 Close Normal Operation (default)
Pin 2-3 Close Clear CMOS Data
* Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to "Pin 2-3 Close".
3. Wait for five seconds.
4. Set the jumper to "Pin 1-2 Close".
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.
(7) Wake On LAN Header: JWOL1/JWOM1 ( optional)
This connector allows you to connect to a LAN card with Wake On LAN
function. You can wake up the computer by remote control through a local area
network. Pin Assignment
1 +3.3V Standby Voltage
2 Ground
3 Wake up
1
1
1

1414
1414
14
EnglishEnglish
EnglishEnglish
English
1
(8) Front USB Header: JUSB3/ JUSB4
The motherboard provides two USB 2.0 Pin Header. USB 2.0 technology
increases Data transfer rate up to a maximum throughput of 480 Mbps, which
is 40 times faster than USB 1.1, and is ideal for connecting high-speed USB
interface peripherals such as USB HDD, digital cameras, MP3 players, printers,
modems, etc.
Pin Assignment Pin Assignment
1 +5V(fused) 2 +5V(fused)
3 USBP-0 4 USBP-1
5 USBP+0 6 USBP+1
7 Ground 8 Ground
9 KEY 10 NC
(9) Power Source Selection for USB: JUSBV1/JUSBV2/JUSBV3 (for version
2.0 only)
JUSBV1/JUSBV2 Assignment Description
JUSBV3
Pin 1-2 close +5V JUSBV1: 5V for USB at the
J1394_USB1 port connector.
JUSBV2: 5V for USB at the
JUSBLAN1port connector.
JUSBV3: 5V for USB at the JUSB3/
JUSB4 port connectors.
Pin 2-3 close +5V Standby Voltage JUSBV1: 5V Standby voltage for USB
at the J1394_USB1 port connector.
JUSBV2: 5V Standby voltage for USB
at the JUSBLAN1 port connector.
JUSBV3: 5V Standby voltage for USB
at the JUSB3/JUSB4 port connectors.
Note: In order to support the function “Power-on the system via USB devices
function,” " JUSBV1/JUSBV2/ JUSBV3" jumper cap should be placed on pin
2-3 respectively.
(10) Serial ATA Connector: JSATA1/JSATA2
The motherboard has a PCI to SATA Controller with 2 channels STAT interface.
It satisfies the SATA 1.0 spec and can transfer data with 1.5GHz speed.
Pin Assignment Pin Assignment
1 Ground 2 TX+
3 TX- 4 Ground
5 RX- 6 RX+
7 Ground
19
1
1

1515
1515
15 EnglishEnglish
EnglishEnglish
English
(11) CD-ROM Audio-In Header: JCDIN1
This header allows you to receive stereo audio input from sound sources, such
as CD-ROM, TV Tuner, MPEG card, etc.
Pin Assignment
1 Left Channel Input
2 Ground
3 Ground
4 Right Channel Input
(12) Front Panel Connector: JPANEL1
The connector is for electrical connection to the front panel switches and
LEDs.
Pin Assignment Function Pin Assignment Function
1 +5V Speaker 2 Sleep Control SleepButton
3 NA Connector 4 Ground
5 NA 6 NA NA
7 Speaker 8 Power LED (+) POWER LED
9 HDD LED (+) Hard DriveLED 10 Power LED (+)
11 HDD LED (-) 12 Power LED (-)
13 Ground Reset Button 14 Power Button Power-on Button
15 Reset Control 16 Ground
17 NA 18 KEY
19 NA IrDA 20 KEY IrDA
21 +5V Connector 22 Ground Connector
23 IRTX 24 IRRX
(13) Power Source Selection for Keyboard/Mouse: JKBV1 (for v2.0 only)
JKBV1 Assignment Description
Pin 1-2 close +5V 5V for keyboard and mouse
Pin 2-3 close +5V_Standby PS/2 Mouse and PS/2 Keyboard
are powered with +5V standby
voltage.
Note: In order to support the function “power-on the system via keyboard and
mouse function, ” “JKBV1” jumper cap should be placed on pin 2-3.
1
SPK
PWR_LED
HLED
SLP
RST
2
24
IR
1
23
IR
ON/OFF
(+) (-)
(+) (-)(+)
1
1

1616
1616
16
EnglishEnglish
EnglishEnglish
English
(14) Power Connector: JATXPWR1/JATXPWR2
The motherboard supports ATX power supply for the power system. Before
installing the power supply connector, please make sure that all components are
installed properly.
PIN Assignment PIN Assignment
1 +3.3V 11 +3.3V
2 +3.3V 12 -12V
3 Ground 13 Ground
4 +5V 14 PS_ON
5 Ground 15 Ground
6 +5V 16 Ground
7 Ground 17 Ground
8 PW_OK 18 -5V
9 +5V_SB 19 +5V
10 +12V 20 +5V
PIN Assignment PIN Assignment
1 +12V 3 Ground
2 +12V 4 Ground
(15) Front 1394 Header: J1394A1 (optional)
Pin Assignment Pin Assignment
1 A1+ 2 A1-
3 Ground 4 Ground
5 B1+ 6 B1-
7 +12V 8 +12V
9 KEY 10 Ground
(16) Digital Audio Connector: JSPDIFO1
The connector is used to connect SPDIF (Sony & Philips Digital Interconnect
Format) interface for digital audio transmission.
Pin Assignment
1 +5V
2 SPDIF_OUT
3 Ground
J1394A1
19
JSPDIFO1
1
1
10
11
20
1
2

1717
1717
17 EnglishEnglish
EnglishEnglish
English
114
JDJ1
1
(18) Front Panel Audio Header: JAUDIO1
The connector allows you to connect to the front panel audio.
Pin Assignment Pin Assignment
1 Mic In/Center 2 Ground
3 Mic Power/Bass 4 Audio Power
5 RT Line Out/Speaker 6 RT Line Out/
Out Right Speaker Out Right
7 Reserved 8 Key
9 LFT Line Out/Speaker 10 LFT Line Out/
Out Left Speaker Out Left
11 RT Line In/Rear 12 RT Line In/Rear
Speaker Right Speaker Right
13 LFT Line In/Rear 14 LFT Line In/
Speaker Left Rear Speaker Left
(19) AUDIO DJ Connector: JDJ1 (optional)
Pin Assignment Pin Assignment
1 SMBDATA 2 SMBCLK
3 INT_B 4 KEY
5 ATX_PWROK
(20) COM2 Header: JCOM2-HEADER (optional)
JCI1
1
(17) Case Open Connector: JCI1 (optional)
Pin Assignment
1 Case Open Signal
2 Ground
Pin Assignment Pin Assignment
1 RIN1 2 RIN3
3 DOUT2 4 DOUT3
5 Ground 6 RIN2
7 DOUT1 8 RIN4
9 -XRI1 10 NA
12
910

1818
1818
18
EnglishEnglish
EnglishEnglish
English
(21) Game Header: JGAME1 (optional)
Pin Assignment Pin Assignment
1 +5V 2 +5V
3 Joystick B Button 1 4 Joystick A Button 1
5 Joystick B Coordinate X 6 Joystick A Coordinate X
7 MIDI Output 8 Ground
9 Joystick B Coordinate Y 10 Ground
11 Joystick B Button 2 12 Joystick A Coordinate Y
13 MIDI Input 14 Joystick A Button 2
15 NA 16 +5V
(22) Back Panel Connectors
1
16
6ChannelSpeakers
SpeakerOut/
Right&Left
LineIn/
RearSpeaker(Left&Right)
MicIn/Center&Bass

1919
1919
19 EnglishEnglish
EnglishEnglish
English
Francais
Caracteristiques de P4VMA-M
CPUCPU
CPUCPU
CPU* Offre les Socket-478.
* Supporte le processeur Intel Pentium 4 jusqu'a 3.2GHz.
* Fonctionnant en Bus Frontal de 400/ 533/ 800MHz.
* Supporte Hyper-Threading.
ChipsetChipset
ChipsetChipset
Chipset
* North Bridge: VIAPM800
* South Bridge: VIA VT8237
Memoire PrincipaleMemoire Principale
Memoire PrincipaleMemoire Principale
Memoire Principale
* Prend en charge un ou deux canaux de donnees DDR de 64 bits de large avec
1 DIMM par canal.
* Bande passant disponible jusqu'a 3.2Go/s (DDR400) pour le mode canal
simple et 6.4Go/s (DDR 400) pour mode canal double.
* Prend en charge les technologies DDR 64Mo, 128 Mo, 256 Mo, 512 Mo, 1Go
* Prend en charge seulement les peripheriques DDR x8, x16. (Ne prend pas en
charge les DIMM et ECC en registres)
* Prend en charge quatre banques de memoire.
* La taille maximum de la memoire est de 2Go.
Super E/SSuper E/S
Super E/SSuper E/S
Super E/S
* Puce: ITE IT8705F.
* Interface de Comptage de Broche Faible.
* Offre la fonctionnalite Super E/S heritee la plus couramment utilisee.
* Initiatives de Controle d'Environnement,
- Moniteur H/W
- Fonction "Smart Guardian" de ITE
SlotsSlots
SlotsSlots
Slots* 3 slots de maitrise de bus PCI 32 bits.
* Un slot CNR. (optionnel)
* Un slot AGP 4X/8X.

2020
2020
20
EnglishEnglish
EnglishEnglish
English
IDE InterneIDE Interne
IDE InterneIDE Interne
IDE Interne
* Supporte quatre disques durs IDE.
* Supporte PIO Mode 4, le Mode Maitre et le Mode de Maitrise de Bus Ultra
DMA 33/66/100/133.
LAN PHY (pour v7.x)LAN PHY (pour v7.x)
LAN PHY (pour v7.x)LAN PHY (pour v7.x)
LAN PHY (pour v7.x)
* PHY : VIA VT6103
* Double Vitesse: 10/100Mbps Negociation automatique .
* Full/Half Duplex.
LAN (pour v2.x)LAN (pour v2.x)
LAN (pour v2.x)LAN (pour v2.x)
LAN (pour v2.x)
* PHY : RTL8100C/RTL8110S
* Double Vitesse: 10/100Mbps(/1000Mbps pour RTL8100C) Negociation
automatique.
* Full/Half Duplex.
IEEE 1394 Puce (optionnel)IEEE 1394 Puce (optionnel)
IEEE 1394 Puce (optionnel)IEEE 1394 Puce (optionnel)
IEEE 1394 Puce (optionnel)
* Puce : VIA VT6307
* Prise 2 ports IEEE 1394.
Codec Son AC'97 InterneCodec Son AC'97 Interne
Codec Son AC'97 InterneCodec Son AC'97 Interne
Codec Son AC'97 Interne
* CMI9739A/9761A
* Conforme aux specifications du codec AC'97.
* Supporte 6 canaux.
* Interface AC’97 2.2 (pour CMI9739A)/ Interface AC’97 2.3 (pour 9761A).
* Supporte S/PDIF-Out.
Peripheriques InternesPeripheriques Internes
Peripheriques InternesPeripheriques Internes
Peripheriques Internes
a. Cote arriere
- 1 port serie, 1 port VGA
- 1 port parallele (mode SPP/EPP/ECP)
- Ports audio en position vertical
- 1 RJ-45 LAN jack.
- Souris PS/2 et clavier PS/2.
- 4 ports USB2.0
- 1 port IEEE1394 (optionnel)
b. Cote frontal :
- 1 port disquette prenant en charge 2 FDD avec 360K, 720K, 1.2M, 1.44M